Manuals / Black Box / Computer Equipment / Network Hardware

Black Box EncrypTight Enforcement Point (ETEP), ET1000A, ET0100A Connecting the Cables ET0010A

Models: ET10000A ET0100A ET0010A ET1000A

1 88

Download 88 pages 24.35 Kb

Page 34

Image 34

Installation

Figure 21 ET0010A rear panel connector for external power supply.

Connecting the Cables: ET0010A

Follow the instructions below to connect the ET0010A to the appropriate network devices (see Figure 22).

To cable the ET0010A:

1For initial setup, connect the RS-232 serial port directly to a PC or workstation. Using the null modem cable supplied by Black Box, insert the RJ-45 connector in the RS-232 port and connect the DB-9 female connector to your PC. This cable can be removed after initial setup is complete.

2Connect the Ethernet management port to a LAN using a Category 5 cable with an RJ-45 connector.

3Connect the remote port to the untrusted network, typically via a router port, using a Category 5 cable with an RJ-45 connector.

4Connect the local port to the local device, such as a server or switch, using a Category 5 cable with an RJ-45 connector.

34	ETEP Installation Guide

Page 34

Image 34

Black Box EncrypTight Enforcement Point (ETEP), ET1000A, ET0100A manual Connecting the Cables ET0010A, To cable the ET0010A

Contents

ET0010A ET0100A ET1000A ET10000A EncrypTight Enforcement Point ETEP Installation GuideCustomer Support Information Page Product Overview InstallationAbout This Document Table of ContentsInitial Setup Maintenance TroubleshootingIndex Purpose About This DocumentContacting Black Box Technical Support Intended audienceETEP Installation Guide About This DocumentETEP Introduction 1 Product OverviewFigure 1 Multipoint Ethernet Encryption using EncrypTight Manager ET0010A Physical Description Front Panel ConnectorsFigure 2 ET0010A Front Panel Connectors Figure 3 ET0010A Status Indicators Status IndicatorsRear Panel Table 1 ET0010A Status IndicatorsET0100A Physical Description Front Panel ConnectorsLED Indicators Figure 4 ET0010A Rear Panel and External Power SupplyElements of Figure 1 Diagnostic display 2 Alarm LED 3 Link indicators Rear PanelFigure 6 ET0100A LED Indicators 4 Power indictorFigure 8 ET1000A Front Panel Connectors ET1000A Physical DescriptionFront Panel Connectors Figure 7 ET0100A Rear PanelElements of Figure 1 Power LED 2 Alarm LED 3 Diagnostic display LED IndicatorsFigure 9 ET1000A LED Indicators 4 Link indicators 10/100 Ethernet management portPower Supply # ET1000A Front Panel LED IndicatorsPower Supply # Rear PanelLED Indicators ET10000A Physical DescriptionFront Panel Connectors Figure 11 ET10000A Front Panel Connectors4 Link indicators 10/100 Ethernet management port Figure 12 ET10000A LED IndicatorsElements of Figure 1 Alarm LED 2 Power LED 3 Diagnostic display 5 Link indicators Gigabit management portPower Supply # ET10000A Front Panel LED IndicatorsPower Supply # Rear PanelETEP Hardware Comparison FeaturesTable 6 ETEP Feature Summary ET0010AETEP Feature Summary SpecificationsTable 7 ET0010A Mechanical and Environmental Specifications See “ET0010A Regulatory Information” on page Table 7 ET0010A Mechanical and Environmental SpecificationsET0100A Mechanical and Environmental Specifications See “ET0100A Regulatory Information” on pageSee “ET1000A Regulatory Information” on page 81 and “ET1000A Table 9 ET1000A Mechanical and Environmental SpecificationsRegulatory Information” on page MIB Support Table 10 ET10000A Mechanical and Environmental SpecificationsModule Table 11 ETEP MIBsFilename ETEP Installation Guide Product OverviewSafety Guidelines 2 InstallationSoftware Requirements Ambient temperature ETEP Site PreparationTable 12 Third party management station software Air flowMaintenance Installation Instructions ET0010AFirewall Ports GroundingTo install the ETEP in a rack Rack Mount InstallationFigure 14 Bottom rear view of the ET0010A, with rack mount brackets 4 Connect the power supply cable to the rear panel connector Figure 18 Front view of ET0010A mounting brackets and power supply Solid Surface InstallationTo install the ETEP on a solid surface Figure 19 Screw holes for rubber feet installation on bottom of unit Figure 20 Rubber feet installedFigure 21 ET0010A rear panel connector for external power supply Connecting the Cables ET0010ATo cable the ET0010A To power on the ETEP Powering On the ET0010AFigure 23 Attaching the power cables on the ET0010A-402 Figure 22 ET0010A CablingET0100A Installation Steps Installing the ET0100ACabling Requirements ET0100A ET0100A Standard CablesUnpacking the Shipping Carton ET0100A Rack-Mount Installation ET0100AET0100A Standard Cables Figure 24 Rack Mounted ETEP, Front Panel View Connecting the Cables ET0100ATo install the ETEP in a rack To cable the ET0100AFigure 26 Properly seated ET0100A power cable Powering on the ET0100ATo power on the ET0100A Figure 25 ET0100A CablingFigure 27 Improperly seated ET0100A power cable Installing the ET1000AFigure 28 ET0100A Front Panel Status Indicators ET1000A Standard Cables Cabling Requirements ET1000AET1000A Installation Steps on pageRack Mount Installation ET1000A Unpacking the Shipping Carton ET1000AFigure 29 Mounting bracket orientation To install the ET1000A in a rackFigure 31 Front view of mounting brackets For DC Power Supply Only Grounding of DC Power Supply ET1000AConnecting the Cables ET1000A For Earth ConnectionPowering on the ET1000A Figure 32 ET1000A Cabling3 Power receptacle for power supply Figure 33 Dual power supplies on the ET1000A rear panelElements of Figure 1 Power cord clips 2 Status LED for power supply 4 Power receptacle for power supply 5 Status LED for power supplyFigure 35 ET1000A Front Panel Status Indicators Installing the ET10000AET10000A Installation Steps Cabling Requirements ET10000A ET10000A Standard CablesUnpacking the Shipping Carton ET10000A To install the ET10000A in a rack Rack Mount Installation ET10000AFigure 36 Mounting bracket orientation Figure 38 Front view of mounting brackets Connecting the Cables ET10000ATo cable the ET10000A Safety Guidelines Powering on the ET10000AFigure 39 ET10000A Cabling Figure 40 Dual power supplies on the ET10000A rear panel Power-Up ProcedureTo power on the ET10000A Shutdown operational codes Shutting Down the ETEPFigure 41 ET10000A Front Panel Status Indicators To shut down the ETEP from the CLIExample pep login admin PasswordETEP Installation Guide Shutting Down the ETEPInstallation ETEP Installation GuideLogging In Through a Serial Link 3 Initial SetupOverview To log in to the CLI via a serial linkConfiguring the Management Port About the management port IP address, mask and gatewayAbout auto-negotiation Figure 42 Management Port Default GatewayTo configure the management port Table 21 Link speeds on the management portip address Management port autoneg command descriptionip ip address subnet mask gateway subnet maskadmin configure config management-interface Setting the Date and Timeadmin configure config management-interface admin configure config management-interfaceTo add a license from the command line Entering a Throughput Licenseadmin configure houradmin configure config management-interface Configuration ExampleManaging the ETEP config date 2008 10 15 12 30 00 config exitSee the user guide for your management software for details Initial SetupETEP Installation Guide ETEP CLI User Guide EncrypTight Manager User GuidePreventative Maintenance 4 MaintenanceWhat To Do If an Appliance Fails Replacing the ET1000A Power Supply Obtaining a License for Replacement UnitsReplacing a Power Supply To replace a power supply in the ET1000AFigure 44 Release lever on power supply # Replacing the ET10000A Power SupplyTo replace a power supply in the ET10000A Figure 46 The power supply bracket is secured with two screws Figure 48 Remove the power supply from the chassisTamper Switch and Zeroization To recover the ETEP following zeroization Cable PinoutsRS-232 Serial Cable ET0010A and ET10000A Figure 50 ET0010A Null Modem Serial CableFigure 51 ETEP100x Null Modem Serial Cable RS-232 Serial Cable ET0100A, ET1000A ModelsETEP Installation Guide Table 25 ETEP100x Null Modem Pin ConnectionMaintenance ETEP Installation GuideLED Indicators 5 TroubleshootingSymptoms and Solutions LED IndicatorsTemperature Threshold and Discarded Traffic Error StateError State Symptoms and Solutions Status Codes ET0010A Diagnostic Code DisplayTable 28 ET0010A Self-Tests ETEP Self-Tests Diagnostic Codes ET0100A, ET1000A and ET10000ATable 29 ET0010A Operational Codes Table 30 ETEP Operational CodesRoHS Directive Appendix A Environmental and Regulatory InformationWEEE Directive Regulatory InformationET0010A Regulatory Information SafetyInterference-Causing Equipment Standard Compliance Notice Canada ImmunitySafety ET0100A Regulatory InformationEuropean Notice Interference-Causing Equipment Standard Compliance Notice CanadaSafety ET1000A Regulatory InformationET0100A Cabling European NoticeSafety EMI/EMCInterference-Causing Equipment Standard Compliance Notice Canada ET1000A Regulatory InformationINSTRUCCIONES DE SEGURIDAD Normas Oficiales Mexicanas NOM Electrical Safety StatementET10000A Regulatory Information Interference-Causing Equipment Standard Compliance Notice Canada13 Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados sobre o contra ellos, poniendo particular atención a los contactos y receptáculos donde salen del aparato ETEP Installation Guide Environmental and Regulatory InformationIndex LEDs See also license Tech support the way it should be Black Box Tech Support FREE! Live. 24/7About Black Box