Carrier 48/50PD05 manual Appendix B - Vfd Information Cont, FAULT CODES cont

48/50PD

		APPENDIX B - VFD INFORMATION (CONT)
		Table 41 — FAULT CODES (cont)
FAULT	FAULT NAME IN PANEL	DESCRIPTION AND RECOMMENDED CORRECTIVE ACTION
CODE
1000		Parameter values are inconsistent. Check for any of the following:
		2001 MINIMUM SPEED > 2002 MAXIMUM SPEED
		2007 MINIMUM FREQ > 2008 MAXIMUM FREQ
	PAR HZRPM	2001 MINIMUM SPEED / 9908 MOTOR NOM SPEED is outside of the range: ---128/+128
		2002 MAXIMUM SPEED / 9908 MOTOR NOM SPEED is outside of the range: ---128/+128
		2007 MINIMUM FREQ / 9907 MOTOR NOM FREQ is outside of the range: --- 128/+128
		2008 MAXIMUM FREQ / 9907 MOTOR NOM FREQ is outside of the range: --- 128/+128
1001	PAR PFA REFNG	Parameter values are inconsistent. Check that 2007 MINIMUM FREQ is negative, when 8123 PFA ENABLE is active.
1002		Parameter values are inconsistent. The number of programmed PFA relays does not match with Interlock
	PAR PFA IOCNF	configuration, when 8123 PFA ENABLE is active. Check consistency of RELAY OUTPUT parameters 1401 through
		1403, and 1410 through 1412. Check 8117 NR OF AUX MOTORS, 8118 AUTOCHANGE INTERV, and 8120
		INTERLOCKS.
1003	PAR AI SCALE	Parameter values are inconsistent. Check that parameter 1301 AI 1 MIN > 1302 AI 1 MAX and that parameter 1304 AI
		2 MIN > 1305 AI 2 MAX.
1004	PAR AO SCALE	Parameter values are inconsistent. Check that parameter 1504 AO 1 MIN > 1505 AO 1 MAX and that parameter 1510
		AO 2 MIN > 1511 AO 2 MAX.
1005		Parameter values for power control are inconsistent: Improper motor nominal kVA or motor nominal power. Check the
		following parameters:
	PAR PCU 2	1.1 < (9906 MOTOR NOM CURR * 9905 MOTOR NOM VOLT * 1.73 / PN) < 2.6
		Where: PN = 1000 * 9909 MOTOR NOM POWER (if units are kW) or PN = 746
		* 9909 MOTOR NOM POWER (if units are HP, e.g., in US)
1006	PAR EXT RO	Parameter values are inconsistent. Check the extension relay module for connection and 1410 through 1412 RELAY
		OUTPUTS 4 through 6 have non---zero values.
1007	PAR FBUS	Parameter values are inconsistent. Check that a parameter is set for field bus control (e.g., 1001 EXT1 COMMANDS =
		10 (COMM)), but 9802 COMM PROT SEL = 0.
1008	PAR PFA MODE	Parameter values are inconsistent. The 9904 MOTOR CTRL MODE must = 3 (SCALAR SPEED) when 8123 PFA
		ENABLE activated.
1009		Parameter values for power control are inconsistent or improper motor nominal frequency or speed. Check for both
	PAR PCU 1	of the following:
		1 < (60 * 9907 MOTOR NOM FREQ / 9908 MOTOR NOM SPEED < 16
		0.8 < 9908 MOTOR NOM SPEED / (120 * 9907 MOTOR NOM FREQ / Motor poles) < 0.992
1010	OVERRIDE/PFA	Override mode is enabled and PFA is activated at the same time. This cannot be done because PFA interlocks cannot
	CONFLICT	be observed in the override mode.

88