Insert NIP400 cards optional | Carrier Access 770-0125-AB specification

Installation

Installing the NIP400 Line Interface Card

Installing the NIP400 Line Interface Card

BROADway supports up to eight NIP400 quad T1/E1 line interface cards installed in slots NIP-1 through NIP-8. To support NIP400 redundant operation, you must install a NIP400 card in slot NIP-8.

Insert NIP400 cards (optional)

NIP RX1	RX2	RX1	RX2	RX3	RX4	CKIN-1 CKIN-2 ETH-1	ETH-2	SCP-1
NIP TX1	NIP TX2	TX1	TX2	TX3	TX4	ALARMS	ACO	SCP-2
	NIP-4			NIP-8
	NIP-3			NIP-7
	NIP-2			NIP-6
	NIP-1			NIP-5

To install the NIP400, open the ejector tab and slide the card into its proper slot until you feel resistance, then push to close the ejector tab into its locking position against the metal rail (the NIP400 has a single ejector only). Check that the card is firmly in place by applying pressure to the ejector tab and the edge of the circuit board to seat the card fully into the chassis. If you are replacing a NIP400 card, wait at least three seconds after removing a NIP400 card before inserting a new one.

WARNING! WHEN INSTALLING OR REPLACING BROADWAY HARDWARE, ALWAYS ADHERE TO GOOD PRACTICE WITH RESPECT TO ESD PROCEDURES—USE A REGULARLY AND PROPERLY TESTED GROUNDING STRAP.

2-16	BROADway - Release 4.00

Image 32

Carrier Access 770-0125-AB installation manual Installing the NIP400 Line Interface Card, Insert NIP400 cards optional

Contents

BROADway Page FCC Requirements, Part Safety of Information Technology EquipmentCompliance Card Service Framing Coding NetworkType Jack Industry Canada ICES-003 Industry Canada CS-03English French Safety Information Electrostatic Discharge ESD Precautions Warranty Product Returns WarrantyLimitation of Warranty & Limitation of Remedies Third-Party Software Notices Sun Microsystems, Inc., Software Notice Preface Table of Contents Configuration Table of Contents Ports and Cables Index Xiv BROADway Release Chapter Overview Installation Chassis Overview Top I/O Panel Front View of the Bits Chassis Top I/O Panel Front View of the ITU Chassis Mounting the Chassis in a Rack Mounting the Chassis in a Rack Side View of the Chassis Cabling Power and Ground Extension Plate Connect to +24VDC or -48VDC power source Ground at power source 48 VDCBROADway Chassis Rear Panel View Connect to Earth ground +24 VDC Ground at power source +24 VDC Feed Cabling the Serial Craft Port Cabling the Ethernet PortConnect to the serial port of a PC Connect an Ethernet cable from a PC to ETH-1 Connect a second clock source Connect a clock source Cabling the Network Synchronization PortCabling the Clock Ports on the Bits Chassis Cabling the Alarm Ports Cabling the Clock Ports on the ITU Chassis Alarm Input Sensing Pin Name Installing the NSP101 Control Card Alarm Output ReportingAlarm Cut Off ACO Insert one or two NSP101 cards Module Red LED Module Green LED Status Top Bottom Active Green LED Status ETH Yellow LED Status Top #1 Bottom Alarm SUM Red LED StatusPWR Red LED #2 PWR Red LED #1 Status Top Bottom Installing the NIP400 Line Interface Card Insert NIP400 cards optional Connect to DSX panels or punch down blocks Cabling the NIP400Clip NIP400 LED Indicators Port LED Port State Grommets Insert NHP160 cards optional Installing the NHP160 Line Interface CardCabling and Inserting the NHP160 Line Interface Card NHP160 LED Indicators A y Installing the BSP200 Line Interface Card BSP200 line terminations Connect BNC coaxial cables BSP200 LED IndicatorsCabling the BSP200 Interface Red LED Interface Green Status Bottom LED Top Grommets Installing OSP155/ESP155/BCP155 Line Interface CardsInsert OSP155, ESP155, or BCP155 cards optional Cabling the OSP155 and BCP155 Installation OSP155, BCP155, and ESP155 LED Indicators Cabling the ESP155 Attaching the Front Panel Applying Power to the Chassis W a y Installing New Cards Maintaining BROADway Hardware Installing Additional OSP155, ESP155 or BCP155 Cards Replacing Failed Cards Maintaining the Fan Tray Fan Board Configuration Configuration Default BROADway IP Address Assigning an IP Address to the BROADway System Assigning a Different IP Address ACT-USERNSP1234CUSTOMER,BROADWAY PS#configure PS#configure PSNSP-config#no interface bvi PS#show BVI status bridge-group number PS#show bvi status Management Access to the BROADway System Viewing Serial Craft Port Settings With the GUILocal SCP-1 Serial Craft Port Access Remote Modem SCP-1 Serial Craft Port Access Ethernet Port Command Line Access Ethernet Port Web Browser GUI Access Logging In With the Web Browser Interface GUI Enter Configuration Configuration Click here to minimize this window This window must remain running in the background Logging In With the Command Line Interface CLI ACT-USERNSP1234username,passwordACT-USERNSP1234 CANC-USERNSP1234 Setting Up User Accounts User Account Management Using the GUI User Account Management Using TL1 RTRV-USERNSP1234ALLRTRV-USERNSP1234ACTIVE RTRV-USERNSP1234ME ENT-USERNSP1234joetech,mypassword,ADMIN,TL1 DLT-USERNSP1234username Changing Your Password Changing Your Password Using the GUIChanging Your Password Using TL1 Current Password field, type your current password Setting the System Date and Time Setting the Date and Time Using the GUISetting the Date and Time Using TL1 ED-DATNSP1234YY-MM-DD,HH-MM-SS Setting System Node Parameters Setting System Node Parameters Using the GUI Setting System Node Parameters Using TL1 RTRV-UDATANSP1234Examples ED-UDATANSP1234US ED-EQPTNSP1234DIS RTRV-EQPTNSP-x.PWR-11234ED-EQPTNSP1234ENA Managing the BROADway Configuration Database Managing the Database Using the GUI Managing the Database Using TL1 RTRV-DBNSP1CPY-DBNSP1RUNNING,SAVED,newdbname CPY-DBNSP1SAVED,offlinename Exporting the BROADway Database to a TL1 Script Re-Starting the BROADway System Using TL1 Copying Files Between NSP101 Controllers Using FTP with the BROADway System INIT-SYSNSP1234ALL NSP1 rtrv-sw-vernsp1234all Upgrading System SoftwareRtrv-sw-vernsp1234all Ftp put c\temp\bw308.zip \ftpFtp cd /FLASH NSP1 set-upgradensp1234bw308,all Set-upgrade command NSP1 set-upgradensp1234bw308 Rolling Back a Software Update Upgrading the Boot ROM NSP1 exec-sysnsp1234bootUpdate NSP1 init-sysnsp1234FORCE TL1 Software Upgrade Commands RTRV-SW-VERNSP1234ALL Appendix a SCP-1 and SCP-2 Connector Pinouts SCP-1 SCP-2 future use Pin Signal Name ETH-1 and ETH-2 Connector Pinouts ETH-1 ETH-2 Pin Signal CKIN-1 and CKIN-2 Connector Pinouts Bits Only Pin Signal NIP400 Connector Pinouts NIP TX1-RX1, NIP TX2-RX2 T1/E1 NIP400 TX tip TX ring RX tip RX ring Circuit Card Ports and Cables Alarms Connector Pinouts Pin Color Name Signal NHP160 Connector Pinouts Scsi Pin Color Signal Ports and Cables Ports and Cables Index Index BROADway Release Index Index