Manuals / CBM America / Computer Equipment / Printer

CBM America CBM-262 user manual Enabling/Disabling automatic sending of the status GS a n

Models: CBM-262

1 131

Download 131 pages 23.34 Kb

Page 107

Input Data Format

(62)Enabling/Disabling automatic sending of the status (GS a n)

Code: [1D] h + [61] h + n

*(0 ≤ n ≤ FF) Data are expressed in Hex code.

This command selects the status that is the object of automatic status sending (ASB: Automatic Status Back).

Bit	Status that is Object of ASB	Value

		0		1
		0		1

0	Status of drawer kick connector pin No. 3.	Disable		Enable

1	On-line	Disable		Enable

2	Error status	Disable		Enable

3	Paper sensor	Disable		Enable

4	Not defined	—		—

5	Not defined	—		—

6	Not defined	—		—

7	Not defined	—		—

•If even one of the status items is enabled, the printer sends the status when this command is executed. After that, each time a status that is enabled changes, that status is sent. At that time, each status expresses the current status, so it is possible that a status that is not enabled for ASB will change.

•If every status is disabled, the auto status sending function (ASB function) is dis- abled.

•If the ASB function in the initial state is enabled, the status at the point when communications were first enabled after the power was switched on is sent.

•The 4-byte status shown below is sent without confirm whether the host is ready to receive or not. Except for the XOFF code, the 4-byte status is always continuous.

•This command is executed when the receiving buffer is developed, so there is a possibility of delay between the reception of the command and sending of the status due to the status of the receiving buffer.

•Even at times when the printer specification is disabled due to peripheral device selection (ESC =), if the status changes, the 4-byte status is sent.

7

97

Image 107

CBM America CBM-262 Enabling/Disabling automatic sending of the status GS a n, Bit Status that is Object of ASB Value

Contents

UsersManual Declaration of Conformity FCC Compliance Statement For America Users EMI Compliance Statement for Canadian Users Important Safety Instructions Page Page Daily Maintenance Contents Print Control Codes Outline Features Accessories Names and Functions of PartsOptional Specifications with Journal Protection Key FeaturesAccessories Standard Specifications without Journal Protection KeyRear Cover Names and Functions of PartsPrinter Unit Receipt Key Power Indicator GreenError Indicator Orange Operation PanelBottom View ConnectorsDIP Switch Above switches are shown in the OFF position Factory DIP Switch SettingsGetting Started Fastening the Cable Terminals Connecting the Interface CableInsert the cables connector into the interface connector Connecting the Cable to the Computer TerminalConnect the drawer kick cable to the drawer kick con- nector Connecting the Drawer Kick CableConnecting the Power Supply Paper Handling Press the I side of the power switch to turn the power on Setting the Receipt Roll PaperSetting the Receipt Roll Paper Open the rear cover Setting the Journal Roll PaperAbout 30 cm Lower the head up lever in the arrow directionSpool Partner Setting the Journal Roll Paper Replacing the Roll Paper Replace the cover Set a new roll of roll paperPrinting Area Specified Paper and Printing AreaSpecified Paper Using Printer Print Density Level Paper Condition Operation Panel KeysTurn the power off, then turn it on again Entering Configuration ModeTest Printing SW1-5 SW1-6 SW1-7 SW1-8 International Character Set DIP SwitchesDIP Switch ContentSW2-4 SW2-3 Parity Setting SW2-2 SW2-1 Baud Rate SettingSensors Error Indications Sensors Error IndicationsPrinter Cover Open Sensor SensorsSensor Lever Setting MethodAdjustment Scale Power LED Error LED Error IndicationsInterfaces Serial Interface Parallel Interface Drawer Kick ConnectorPin No SpecificationsSerial Interface Input/Output Circuits Explanation of Signal NamesReset by Init Reset by DSRProtocols Parallel Interface Timing ChartWhen Receiving the Init Signal Init Function Signal Lines and Pin ArrangementChapter Interfaces Electrical Characteristics Drawer Kick ConnectorDrawer Kick Drive Signal Signal Name Function Connector Connection DiagramDrive Circuit Interfaces List of Control Codes Input Data Format Print Control CodesList of Control Codes Character CommandList of Control Codes Print Control Codes Line feed LF Print command CRInput Data Format Horizontal tab HTSending the status in real time DLE EOT n Printing in the page mode and return FFCanceling of print data in the page mode Journal tab RSDistinguishing the Sending Status Command and Function StatusBit Function Value Bit FunctionError Factor Status when n = 3 is specified Real time enquiry to printer DLE ENQ n Printing of data in the page mode ESC FFSetting the space between characters ESC SP n Specifying the print mode all at once ESC ! n Specifying/Clearing the download character set ESC % n Specifying the absolute print position ESC $ n1 n2Defining download characters ESC & s n m a D1 D2~Dn Example Case of Font B Specifying a bit image ESC * m n1 n2 D1~Dn MHex Mode Vertical Direction Horizontal DirectionRelationship between bit image data and printed dots Specifying the 1/6 inch line feed amount ESC Specifying/Clearing underline ESC nSpecifying the line feed amount ESC 3 n Erasing download characters ESC ? n Controlling data input ESC = nSpecifying/Clearing bold characters ESC E n Setting the horizontal tab position ESC D n NULPrinter initialization ESC @ Printing and paper feeding ESC J n Specifying/Clearing double strike characters ESC G nESC SP, FS S Selecting the page mode ESC LNHex Character Set Selecting international characters ESC R nSelecting the standard mode ESC S Starting Point → → → → Left to Right Top Left Setting the printing area in the page mode ESC W Input Data Format Specifying the relative printing position ESC \ n1 n2 Selecting the printing sheet ESC c 0 n Arranging the printing position ESC a nSelecting the setting sheet ESC c 1 n Enabling/Disabling the panel switch ESC c 5 n Partial cut ESC m Generates a specification pulse ESC p m n1 n2Print and feed paper n lines ESC d n Full cut ESC lCharacter Type Selecting the character code table ESC t nPeripheral sevice status signal ESC u n Sending the printer status ESC Specifying/Clearing inverted characters ESC n Bits Value Specifying the character size GS ! nPrint Control Codes Defining a downloaded bit image GS * n1 n2 Dn Printing a downloaded bit image GS / m Mode Name Vertical Dot DensityStarting and ending a macro definition GS Hex Print Position Specifying/Clearing Black/White reverse printing GS B nSelecting the HRI character print position GS H n Printable Range Left Margin Width of Print Area Setting the left margin GS L n1 n2Specifying/Clearing reduced character printing GS M n Setting the basic calculation pitch GS P x y Cutting of paper GS V m, GS V m n Printable Area Left Margin Print Area Width Setting the print area width GS W n1 n2Is erased Print area width Printable Area Left Margin Left marginInput Data Format Execution of a macro GS n1 n2 n3 Bit Status that is Object of ASB Value Enabling/Disabling automatic sending of the status GS a nLOW High Bit Status ValueThird Byte Paper Sensor Information 100 Selecting the font of HRI characters GS f nSelecting the bar code height GS h n NHex Font101 Printing bar codes. GS kn 1 Dn NULDefinition Range 102 103 Sending of the status GS r nBit Printer Status Value 104 105 Selecting the horizontal size of a bar code GS w n106 107 Code Japanese Code Table International Character Code Table108 Code109 110 111 Japanese Code Table112 International Character Code Table113 Appendices114 Journal Protection Key115 Maintenance, CautionsRemoving Paper Jams Operating Temperature and Humidity 117 SpecificationsModel Classification 118 Basic SpecificationsSpecified Paper 119120 External ViewPC74903-10