Manuals / CBM America / Computer Equipment / Printer

CBM America CBM-262 user manual Serial Interface, Specifications, Pin No

Models: CBM-262

1 131

Download 131 pages 23.34 Kb

Page 42

6

Chapter 6 Interfaces

Serial Interface

Specifications

Transmission Method Start-Stop Synchronous Full Duplex Communications

		Signal Level			RS-232C

		Baud Rate			2400, 4800, 9600, 19200

		Data Length			7 or 8 bits

		Start Bit			1 bit

		Stop Bit			Receiving 1 bit; Transmitting			2 bits or more

		Parity			Even, Odd, No Parity

		Connector			Printer Side Compatible with DDK 17LE-13250-27

Signal Lines and Pin Arrangement

	13							1
	25							14

	Pin No.		Signal Name		Direction	X-ON/X-OFF		DTR/DSR
	1			F.GND		Connects the Host CPU
	1			F.GND		and printer.
						and printer.
						Sends transmission data
	2			TXD	OUT	and X-ON/X-OFF		Not used.
	2			TXD	OUT	signals to the Host CPU		Not used.
						signals to the Host CPU
						from the printer.

						Transmission data from
	3			RXD	IN	the Host CPU to the
						printer.
	4			RTS	OUT	Pulls up the signal to
						+10V at 3.3k ohms.

								Data are sent when the
	6			DSR	IN	Not used.		status information send
								signal is “HIGH.”
	7			S.GND
	20			DTR	OUT	Always HIGH.		LOW when Busy.
	20			DTR	OUT	Always HIGH.		HIGH when Ready.
								HIGH when Ready.

	25			INIT	IN(*1)	Printer's Reset signal.

•IN indicates a signal from the Host to the printer. OUT indicates a signal from the printer to the Host.

*1 25pin, INIT is HIGH or the TTL-HIGH level of input (+2V~+15V) .

32

Image 42

CBM America CBM-262 user manual Serial Interface, Specifications, Pin No

Contents

UsersManual Declaration of Conformity FCC Compliance Statement For America Users EMI Compliance Statement for Canadian Users Important Safety Instructions Page Page Daily Maintenance Contents Print Control Codes Features Accessories Names and Functions of Parts OutlineStandard Specifications without Journal Protection Key FeaturesAccessories Optional Specifications with Journal Protection KeyNames and Functions of Parts Printer UnitRear Cover Operation Panel Power Indicator GreenError Indicator Orange Receipt KeyConnectors Bottom ViewFactory DIP Switch Settings DIP Switch Above switches are shown in the OFF positionGetting Started Connecting the Cable to the Computer Terminal Connecting the Interface CableInsert the cables connector into the interface connector Fastening the Cable TerminalsConnecting the Drawer Kick Cable Connect the drawer kick cable to the drawer kick con- nectorConnecting the Power Supply Paper Handling Setting the Receipt Roll Paper Press the I side of the power switch to turn the power onSetting the Receipt Roll Paper Setting the Journal Roll Paper Open the rear coverLower the head up lever in the arrow direction About 30 cmSpool Partner Setting the Journal Roll Paper Replacing the Roll Paper Set a new roll of roll paper Replace the coverSpecified Paper and Printing Area Specified PaperPrinting Area Using Printer Operation Panel Keys Print Density Level Paper ConditionEntering Configuration Mode Turn the power off, then turn it on againTest Printing Content DIP SwitchesDIP Switch SW1-5 SW1-6 SW1-7 SW1-8 International Character SetSW2-2 SW2-1 Baud Rate Setting SW2-4 SW2-3 Parity SettingSensors Error Indications Sensors Error IndicationsSensors Printer Cover Open SensorSetting Method Adjustment ScaleSensor Lever Error Indications Power LED Error LEDSerial Interface Parallel Interface Drawer Kick Connector InterfacesSpecifications Serial InterfacePin No Explanation of Signal Names Input/Output CircuitsReset by DSR Reset by InitProtocols Timing Chart Parallel InterfaceWhen Receiving the Init Signal Init Signal Lines and Pin Arrangement FunctionChapter Interfaces Drawer Kick Connector Drawer Kick Drive SignalElectrical Characteristics Connector Connection Diagram Signal Name FunctionDrive Circuit Interfaces Print Control Codes List of Control Codes Input Data FormatCharacter Command List of Control CodesList of Control Codes Print Control Codes Horizontal tab HT Print command CRInput Data Format Line feed LFJournal tab RS Printing in the page mode and return FFCanceling of print data in the page mode Sending the status in real time DLE EOT nCommand and Function Status Distinguishing the Sending StatusBit Function Bit Function ValueError Factor Status when n = 3 is specified Printing of data in the page mode ESC FF Real time enquiry to printer DLE ENQ nSetting the space between characters ESC SP n Specifying the print mode all at once ESC ! n Specifying the absolute print position ESC $ n1 n2 Specifying/Clearing the download character set ESC % nDefining download characters ESC & s n m a D1 D2~Dn Example Case of Font B MHex Mode Vertical Direction Horizontal Direction Specifying a bit image ESC * m n1 n2 D1~DnRelationship between bit image data and printed dots Specifying/Clearing underline ESC n Specifying the 1/6 inch line feed amount ESCSpecifying the line feed amount ESC 3 n Controlling data input ESC = n Erasing download characters ESC ? nSetting the horizontal tab position ESC D n NUL Printer initialization ESC @Specifying/Clearing bold characters ESC E n Specifying/Clearing double strike characters ESC G n Printing and paper feeding ESC J nSelecting the page mode ESC L ESC SP, FS SSelecting international characters ESC R n NHex Character SetSelecting the standard mode ESC S Starting Point → → → → Left to Right Top Left Setting the printing area in the page mode ESC W Input Data Format Specifying the relative printing position ESC \ n1 n2 Arranging the printing position ESC a n Selecting the printing sheet ESC c 0 nSelecting the setting sheet ESC c 1 n Enabling/Disabling the panel switch ESC c 5 n Full cut ESC l Generates a specification pulse ESC p m n1 n2Print and feed paper n lines ESC d n Partial cut ESC mSelecting the character code table ESC t n Character TypePeripheral sevice status signal ESC u n Sending the printer status ESC Specifying/Clearing inverted characters ESC n Specifying the character size GS ! n Bits ValuePrint Control Codes Defining a downloaded bit image GS * n1 n2 Dn Mode Name Vertical Dot Density Printing a downloaded bit image GS / mStarting and ending a macro definition GS Specifying/Clearing Black/White reverse printing GS B n Selecting the HRI character print position GS H nHex Print Position Setting the left margin GS L n1 n2 Printable Range Left Margin Width of Print AreaSpecifying/Clearing reduced character printing GS M n Setting the basic calculation pitch GS P x y Cutting of paper GS V m, GS V m n Setting the print area width GS W n1 n2 Printable Area Left Margin Print Area WidthPrintable Area Left Margin Left margin Is erased Print area widthInput Data Format Execution of a macro GS n1 n2 n3 Enabling/Disabling automatic sending of the status GS a n Bit Status that is Object of ASB ValueBit Status Value LOW HighThird Byte Paper Sensor Information NHex Font Selecting the font of HRI characters GS f nSelecting the bar code height GS h n 100Printing bar codes. GS kn 1 Dn NUL Definition Range101 102 Sending of the status GS r n Bit Printer Status Value103 104 Selecting the horizontal size of a bar code GS w n 105106 Code Japanese Code Table International Character Code Table 107Code 108109 110 Japanese Code Table 111International Character Code Table 112Appendices 113Journal Protection Key 114Maintenance, Cautions Removing Paper Jams115 Operating Temperature and Humidity Specifications Model Classification117 Basic Specifications 118119 Specified PaperExternal View 120PC74903-10