Printing and paper feeding ESC J n | CBM America CBM-262 specification

Input Data Format

(24)Specifying/Clearing double strike characters (ESC G n)

Code: [1B] h + [47] h + n

* (0 ≤ n ≤ FF) Data are expressed in Hex code.

This command specifies and clears double strike characters.

•The least significant bit (n0) in n is valid.

•Control by the least significant bit (n0) is as follows.

n0 = 0: Clears double strike characters.

n0 = 1: Specifies double strike characters.

•In this printer, the effects of double strike printing are the same as those of bold printing.

(25)Printing and paper feeding (ESC J n)

Code: [1B] h + [4A] h + n

* (0 ≤ n ≤ FF) Data are expressed in Hex code.

This command prints the data in the print buffer and feeds the paper [n x basic calcu- lation pitch] inches.

•After execution, the top of the line becomes the next print position.

•This has no influence on the line feed amount set by ESC 2 or ESC 3.

•The basic calculation pitch is set by GS P.

•If there is a fraction as a result of calculations, interpolation is carried out at the mechanism's minimum pitch. Remainders are cut off.

•In the Standard mode, the basic calculation pitch (y) for the vertical direction is used.

•If used in the Page mode, movement from the starting point is as follows.

(1)If the starting point is specified as “top left” or “bottom right” by ESC T, the printing position is moved in the paper feed direction (the vertical direction of the characters). At this time, the vertical basic calculation pitch (y) is used.

(2)If the starting point is specified as “top right” or “bottom left” by ESC T, the printing position is moved in the direction perpendicular to the paper feed direction (the vertical direction of the characters). At this time, the horizontal basic calculation pitch (x) is used.

•If [n x basic calculation pitch] exceeds 40 inches, the 40 inch portion of the paper feed is executed.

7

67

Image 77

CBM America CBM-262 user manual Specifying/Clearing double strike characters ESC G n, Printing and paper feeding ESC J n

Contents

UsersManual Declaration of Conformity FCC Compliance Statement For America Users EMI Compliance Statement for Canadian Users Important Safety Instructions Page Page Daily Maintenance Contents Print Control Codes Outline Features Accessories Names and Functions of Parts Accessories FeaturesStandard Specifications without Journal Protection Key Optional Specifications with Journal Protection Key Rear Cover Names and Functions of PartsPrinter Unit Error Indicator Orange Power Indicator GreenOperation Panel Receipt Key Bottom View Connectors DIP Switch Above switches are shown in the OFF position Factory DIP Switch Settings Getting Started Insert the cables connector into the interface connector Connecting the Interface CableConnecting the Cable to the Computer Terminal Fastening the Cable Terminals Connect the drawer kick cable to the drawer kick con- nector Connecting the Drawer Kick Cable Connecting the Power Supply Paper Handling Press the I side of the power switch to turn the power on Setting the Receipt Roll Paper Setting the Receipt Roll Paper Open the rear cover Setting the Journal Roll Paper About 30 cm Lower the head up lever in the arrow direction Spool Partner Setting the Journal Roll Paper Replacing the Roll Paper Replace the cover Set a new roll of roll paper Printing Area Specified Paper and Printing AreaSpecified Paper Using Printer Print Density Level Paper Condition Operation Panel Keys Turn the power off, then turn it on again Entering Configuration Mode Test Printing DIP Switch DIP SwitchesContent SW1-5 SW1-6 SW1-7 SW1-8 International Character Set SW2-4 SW2-3 Parity Setting SW2-2 SW2-1 Baud Rate Setting Sensors Error Indications Sensors Error Indications Printer Cover Open Sensor Sensors Sensor Lever Setting MethodAdjustment Scale Power LED Error LED Error Indications Interfaces Serial Interface Parallel Interface Drawer Kick Connector Pin No SpecificationsSerial Interface Input/Output Circuits Explanation of Signal Names Reset by Init Reset by DSR Protocols Parallel Interface Timing Chart When Receiving the Init Signal Init Function Signal Lines and Pin Arrangement Chapter Interfaces Electrical Characteristics Drawer Kick ConnectorDrawer Kick Drive Signal Signal Name Function Connector Connection Diagram Drive Circuit Interfaces List of Control Codes Input Data Format Print Control Codes List of Control Codes Character Command List of Control Codes Print Control Codes Input Data Format Print command CRHorizontal tab HT Line feed LF Canceling of print data in the page mode Printing in the page mode and return FFJournal tab RS Sending the status in real time DLE EOT n Distinguishing the Sending Status Command and Function Status Bit Function Value Bit Function Error Factor Status when n = 3 is specified Real time enquiry to printer DLE ENQ n Printing of data in the page mode ESC FF Setting the space between characters ESC SP n Specifying the print mode all at once ESC ! n Specifying/Clearing the download character set ESC % n Specifying the absolute print position ESC $ n1 n2 Defining download characters ESC & s n m a D1 D2~Dn Example Case of Font B Specifying a bit image ESC * m n1 n2 D1~Dn MHex Mode Vertical Direction Horizontal Direction Relationship between bit image data and printed dots Specifying the 1/6 inch line feed amount ESC Specifying/Clearing underline ESC n Specifying the line feed amount ESC 3 n Erasing download characters ESC ? n Controlling data input ESC = n Specifying/Clearing bold characters ESC E n Setting the horizontal tab position ESC D n NULPrinter initialization ESC @ Printing and paper feeding ESC J n Specifying/Clearing double strike characters ESC G n ESC SP, FS S Selecting the page mode ESC L NHex Character Set Selecting international characters ESC R n Selecting the standard mode ESC S Starting Point → → → → Left to Right Top Left Setting the printing area in the page mode ESC W Input Data Format Specifying the relative printing position ESC \ n1 n2 Selecting the printing sheet ESC c 0 n Arranging the printing position ESC a n Selecting the setting sheet ESC c 1 n Enabling/Disabling the panel switch ESC c 5 n Print and feed paper n lines ESC d n Generates a specification pulse ESC p m n1 n2Full cut ESC l Partial cut ESC m Character Type Selecting the character code table ESC t n Peripheral sevice status signal ESC u n Sending the printer status ESC Specifying/Clearing inverted characters ESC n Bits Value Specifying the character size GS ! n Print Control Codes Defining a downloaded bit image GS * n1 n2 Dn Printing a downloaded bit image GS / m Mode Name Vertical Dot Density Starting and ending a macro definition GS Hex Print Position Specifying/Clearing Black/White reverse printing GS B nSelecting the HRI character print position GS H n Printable Range Left Margin Width of Print Area Setting the left margin GS L n1 n2 Specifying/Clearing reduced character printing GS M n Setting the basic calculation pitch GS P x y Cutting of paper GS V m, GS V m n Printable Area Left Margin Print Area Width Setting the print area width GS W n1 n2 Is erased Print area width Printable Area Left Margin Left margin Input Data Format Execution of a macro GS n1 n2 n3 Bit Status that is Object of ASB Value Enabling/Disabling automatic sending of the status GS a n LOW High Bit Status Value Third Byte Paper Sensor Information Selecting the bar code height GS h n Selecting the font of HRI characters GS f nNHex Font 100 101 Printing bar codes. GS kn 1 Dn NULDefinition Range 102 103 Sending of the status GS r nBit Printer Status Value 104 105 Selecting the horizontal size of a bar code GS w n 106 107 Code Japanese Code Table International Character Code Table 108 Code 109 110 111 Japanese Code Table 112 International Character Code Table 113 Appendices 114 Journal Protection Key 115 Maintenance, CautionsRemoving Paper Jams Operating Temperature and Humidity 117 SpecificationsModel Classification 118 Basic Specifications Specified Paper 119 120 External View PC74903-10