CBM America CBM-262 Entering Configuration Mode, Turn the power off, then turn it on again

Operation Panel Keys

Entering Configuration Mode

Select YES (R) or NO (J) to the printed question and set it.

If YES: Press the RECEIPT key.

If NO: Press the JOURNAL key.

• Perform the operation with the front cover removed.

1.With roll paper set, switch the power on while pressing both the RECEIPT key and the JOURNAL key.

This causes the printer to enter the printer configuration setting mode, and the printer will print the following text in accordance with the selected menu for each item.

PRINTER SETTING MODE

YES:Push (R)eceipt Key

NO :Push (J)ournal Key

ROM(Even):AW32-0A0A

ROM(Odd) :AW33-0A0A

ROM Date :MAY-28-1996

Reset Current Settings
To Factory Settungs?	YES (R) NO (J)
Print Current Settings?	YES (R) NO (J)
Current Settings
<HARDWARE SETTINGS>
:RECEIPT DENSITY	1/2/3/4
:JOURNAL DENSITY	1/2/3/4
:COVER OPEN SENSOR	VALID/INVALID
:AUTO CUTTER	VALID/INVAILD
:AUTO LOADING	VALID/INVALID
:R PAPER NEAR END	VALID/INVAILD
:J PAPER NEAR END	VALID/INVAILD
:CR CONTROL	CR+KF/LF/IGNORE
:KANJI MODE	VALID/INVALID
:RESET BY INIT	VALID/INVALID
:RESET BY DSR	VALID/INVALID
:ERROR HANDSHAKE	BUSY/INVALID
:INPUT BUFFER	8KB/1LINE
<CHARACTER SETTINGS>
:CHARACTER TABLE	PC473/PC850
:COUNTRY	JAPAN/U.S.A
	FRANCE/GERMANY
	U.K./DENMARK
	SWEDEN/ITALY
	SPAIN/NORWAY
	DENMARK2/SPAIN2
	LATIN/KOREA
	LEGAL
<SERIAL SETTINGS>
:DATA BIT	8BITS/7BITS
:PARITY	NONE/ODD/EVEN
:PROTOCOL	DTR:DSR
	XON:XOFF
:BUADRATE	9600/4800
	2400/19200
Change Current Setting?	YES(R) NO(J)
:RECEIPT DENSITY	1
	YES(R) NO(J)
:JOURNAL DENSITY	1
	YES(R) NO(J)
:COUVER OPEN SENSOR VALID
	YES(R) NO(J)
:AUTO CUTTER	VALID
	YES(R) NO(J)
:AUTO LOADING	VALID
	YES(R) NO(J)
:R PAPER NEAR END	INVALID
	YES(R) NO(J)
:J PAPER NEAR END	INVALID
	YES(R) NO(J)
:CR CONTROL	CR+LF
	YES(R) NO(J)
:KANJI MODE	INVALID
	YES(R) NO(J)
:RESET BY INIT	VALID
	YES(R) NO(J)
:RESET BY DSR	VALID
	YES(R) NO(J)
:ERROR HANDSHAKE	BUSY
	YES(R) NO(J)
Current Settings
:RECEIPT DENSITY	T1/2/3/4
:JOURNAL DENSITY	1/2/3/4
:COVER OPEN SENSOR	VALID/INVALID
:AUTO CUTTER	VALID/INVALID
:AUTO LOADING	VALID/INVALID
:R PAPER NEAR END	VALID/INVALID
:J PAPER NEAR END	VALID/INVALID
:CR CONTROL	CR+LF/LF/IGNORE
:KANJI MODE	VALID/INVALID
:RESET BY INIT	VALID/INVALID
:RESET BY DSR	VALID/INVALID
:ERROR HANDSHAKE	BUSY/INVALID

SETTING MODE END!!

1

2

3

4

5

6

7

8

1.Prints the ROM version and the date.

2.If YES is selected, it resets the factory default settings, then moves to the following line. If NO is selected, the following line is printed.

3.If YES is selected, the currently set menues are printed.

If NO is selected, the line in 5 is printed.

4.The input buffer, character settings (Interna- tional character code) and serial protocol set- tings are as set by the DIP switches.

5.If YES is selected, after the line in 6, printing of the settings for each item is begun.

If NO is selected, the printing of 8 is done, and setting of the printer ends.

6.Select NO until the menu of all the setting items is set as desired. When the content is correct, select YES. If YES is selected, the setting contents are recorded in non-volatile memory and the printer prints the next item. When Error handshake setting item is ended, the set contents (7) and 8 are printed, then printer set up is ended.

4

2.Turn the power off, then turn it on again.

The set contents become enabled.

23