100, Decay Decay Adjust, Delay Delay Adjust | ClearOne comm PSR1212

100	Appendices ~ Appendix E: Serial Commands

DECAY - Decay Adjust

This command selects/reports the setting of the decay rate for a specified input. Command form: DEVICE DECAY <Channel> [Value]

Argument details

Name	Description
Device	0–7 or * to select all units
DECAY	Command form
Channel	Range 1–8 (selects mic input)
Value	1 = Slow, 2 = Medium, 3 = Fast, Null to return current state

Example: #43 DECAY 1 3 On PSR1212 unit 3 (#43), the decay rate (DECAY) for mic channel 1 is set to fast (3).

DELAY - Delay Adjust

This command selects/reports the delay time of each assignable processing channel. Command form: DEVICE DELAY <Channel> [Value]

Argument details

Name	Description	Units
Device	0–7 or * to select all units
DELAY	Command form
Channel	A–H (select processing channel)
Value	0.00 to 500 (selects delay)	ms
	Null to return current state

Example: #46 DELAY A 200 On PSR1212 unit 6 (#46) the delay (DELAY) for processing channel A is set to 200ms.

DELAYSEL - Delay Select

This command selects/reports the delay activation of an assignable processing channel.

Command form: DEVICE DELAYSEL <Channel> [Value]

Argument details

Name	Description
Device	0–7 or * to select all units
DELAYSEL	Command form
Channel	A–H (select processing channel)
Value	0 = Off, 1 = On, 2 = Toggle, Null to return current state

Example: #44 DELAYSEL A 1 On PSR1212 unit 4 (#44) the delay (DELAYSEL) within processing channel A is enabled (1).

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 106

ClearOne comm PSR1212 operation manual 100, Decay Decay Adjust, Delay Delay Adjust, Delaysel Delay Select

Contents

PSR1212 Digital Matrix Mixer PSR1212 Installation ClearOne Part No Jan 2007Rev Table of Contents System Configuration Advanced Configuration Appendices OperationControl 127 Technical Services Group ~ 1-800-283-5936 USA ~ Introduction Product overview New Features Technical Support Professional Services GroupSales and Customer Service ClearOne Communications EuMEA GmbH Controls and Connections UnpackingFront panel Rear panel Introduction ~ Controls and Connections Introduction ~ Controls and Connections Networking Expansion bus Operational Requirements PowerEquipment placement Environmental Installation Hardware Setup Three terminals ConnectorTo connect the unit Rear-panel audio contacts from left to right + positive Expansion bus connections Installation ~ Networking UnitsNetworking Units To create an expansion bus network Device IDs Mixer modeTo select a mixer mode To assign device IDs LCD menu tree Installation ~ LCD ProgrammingLCD Programming Pressing Esc at the top of the tree does nothing System menu To adjust a parameterSelect Preset Run Macro RS-232 menu Meter menu Enable ModemClear Password Flow Control hardware Inputs menu Outputs menu Gain Matrix Technical Services Group ~ 1-800-283-5936 USA ~ System Configuration Ware Requirements Creating Floppy Disk Copies Installing G-WareTo install G-Ware Directory Creating a new site Site SetupTo create a new site To manually add units Adding a PSR1212To auto-detect units Select the PSR1212 icon and click Add Configuring Unit Properties To configure Unit Properties System Configuration ~ Site Setup Ware Screens Flow Screen Safety Mute Copying and pasting settingsStatus bar Matrix Screen 20. G-Ware Matrix Screen Process A-H routing Audio RoutingExpansion bus O-Z routing Cross point attenuation System Configuration ~ Audio Routing Matrix report Inputs and Outputs Inputs Active Filter Pwr Phantom PowerFilters Type System Configuration ~ Inputs and Outputs Table View Activation To configure filtersGate NOM count Manual Off deactivates the mic Adaptive Ambient PA Adaptive ModeChairman Override Gate Ratio Decay Rate PA Adapt and AEC Reference To create a virtual reference Click Close to exit the window Gating Group Select To configure gating group settingsTo assign a gating group 36. Gain Adjustment Min/Max limits Meters 38. Inputs 9-12 Configuration window 40. Gain meters Outputs NOM Optimizing output gain structure To Expansion Bus O-Z Expansion BusesFrom Expansion Bus O-Z Routing of audio to Processing Processing A-H Established only Cmprs compressorGroup 47. Processing Filters window Add Filter PhaseBypass Remove Filter Delay DelaySelect the Bypass Delay Changes you make in the distance and temperature fields 50. Process Gain adjust and meter Optimizing process gain structure Overview PresetsCreating Presets Local Affected when the preset is run Preset Configuration panePreset password is set in the Unit Properties window see Advanced Configuration ~ Presets Assigning virtual references to the preset To create a preset Storage space To run a preset using G-Ware Running presetsRunning multiple presets simultaneously To run a preset using front panel control Room combining example Flags to 0 which ensures Four macros one for each configuration are set up as follows Creating macros To create a macro using Macro RecorderMacros Existing To create a macro using Macro Editor 16 Macro Name window To edit a macro To add or insert a command lineEditing macros To delete a macro To run a macro using the Select panel or Gpio To run a macro using G-WareTo run a macro using front panel control Running macros To use pink or white noise Signal GeneratorUtilities Select the PSR1212 Unit and Input Channel you want to use To use tone Document Compare UtilityOperation ~ Utilities To compare site files Open window Copying settings Print Preview window Print Reports Print Reports window To upgrade firmware GFirm Firmware Utility 13. Selecting baud rate Before using G-Ware Switcher Ware SwitcherTo use G-Ware Switcher Monitoring Views Copy and paste settingsMessage Log Gate View To configure Meter Views Meter Views Gpio Builder To program control/status pinsControl/Status a XAP IR Remote Ments for use in a presetRemote Builder Control ~ Remote Builder Control ~ Remote Builder To program the XAP IR Remote Select IR Remote default from the Select Remote Type listClearOne Control Panels Up to five control panels Panel To program the Volume panelOne IR remote can To program the Select panel Select Panel selected in the Remote Builder Modem password is Remote Modem AccessSerial commands RS-232 Port To run a command string Command stringsTo create a command string Control ~ RS-232 Port Technical Services Group ~ 1-800-283-5936 USA ~ Appendix a Specifications Appendices ~ Appendix B Pinouts Appendix B PinoutsRS-232 COM DCE port pinout female Pin Number Control Control/Status a Port Pinout female Control/Status connectorsPin Definable Type Default Description Control/Status Control/Status B port pinout Preset select bit+5VDC, 300mA Line connector pinout RS-485 Remote Panel a and B connectorsSet connector pinout PinDescription Appendix C Control Panel Connecting the Control PanelAppendices ~ Appendix C Control Panel Control Panel Appendices ~ Appendix C Control Panel Appendices ~ Appendix D Accessories Appendix D AccessoriesAccessory ClearOne Part Number Conventions Appendix E Serial CommandsCommand structure Example Type and device IDs Appendices ~ Appendix E Serial CommandsGroups and channels Unit type Meter type definitions Serial command error codesError number Text message Explanation/Solution Appendices ~ Appendix E Serial PSR1212 Serial commands Command Function Selects/reports signal generator activation Selects/reports NOM setting on outputSelects/reports off attenuation mode for Channels AGC Automatic Gain Control Aamb Adaptive Ambient ModeAmblvl Ambient Level Adjust Argument details Baud Baud Rate Chairo Chairman Override ModeCgroup Compressor Group Select Compress Compressor Adjust Compsel Compression Select Delaysel Delay Select Decay Decay AdjustDelay Delay Adjust 100 Did Device ID Dfltm Default Meter101 Channel Group Examples Filter Filter Adjust102 Name Description Units Filtsel Filter Select FMP First Mic Priority Mode103 Flow Flow Control FPP Front Panel Passcode Gain Gain Adjustment104 Button assignment Gate Gate Status GHOLD- Gate Hold Time Adjust105 Example 106 Gmode Gating ModeGratio Gate Ratio Adjust Gover Gating Override Label Label Greport Gate ReportGrpsel Gating Group Select 107 108 LMO Last Mic On ModeLock Preset and Macro Lock LFP Lock Front Panel 109 Lockprst Apply the lock to a preset or macroLockpwd Set preset/macro password LVL Level Lvlrrate Level Report Rate 110Lvlreport Level Report = Toggle 111 Master Expansion Bus Master ModeMAX Maximum Gain Setting Macro Macro Execution/Reporting MIN Minimum Gain Setting Mdmode Modem Mode112 113 Minmax Minimum and Maximum Gain SettingMinit Modem Initialization String 114 Mline Mic/Line AdjustMpass Modem Password Mmax Maximum Number of Microphones 115 Mtrxlvl Matrix Attenuation AdjustmentMtrx Matrix 116 NOM Number of Open Microphones ModeOffa Off Attenuation Mode Mute Mute Preset Preset Execution/Reporting PAA PA Adaptive ModePP Phantom Power 117 Supported special characters 118Prgstring Program String String location Refsel PA/AEC Reference Select Ramp Ramp Gain Adjustment119 Name Description Unit 120 Refset Reference channel setupSermode Serial Mode Serecho Serial Echo Siggen Signal Generator Sftymute Safety mute121 String String Execution Sigtout Signal Generator Time Out122 Tout Time Out Select UID Unit ID Command Value Null to return value123 VER Version Appendix F Warranty 124 Appendices ~ Appendix F Warranty 125 Appendix G Compliance Safety Information126 FCC Part 15 Compliance 127 Glossary 128 Glossary 129 130 131 132 133 Signal Delay Used for 134 135 136 Index 137 138 PhaseFrequency response 139