System Configuration ~ Site Setup | ClearOne comm PSR1212 specification

26	System Configuration ~ Site Setup

8.If a modem is connected to the PSR1212 unit, select Use Modem and enter the initialization string. Click OK; the PSR1212 will initialize the modem.

9.Click the Security tab. Create a modem password. The password will be required before control of the system through remote modem access is allowed. The default modem password is a carriage return.

10.Preset/Macro Password enables you to password protect your individual presets and macros. To create a password, click Preset/Macro Password.

Creating a Preset/Macro Password does not automatically lock all presets or macros. Presets are locked in the Preset Configuration Mode. See page 54 for more information. Macros are locked in the Macro Editor. Presets and

Figure 3.14. Unit Properties Security tab Macros that are locked do not require the password to be run. However, the password is required to make changes.

11.Select the Front Panel Lock Mode.

•Unlock Panel leaves the front panel controls unlocked.

•Lock Panel locks the front panel immediately.

•Lock When Timeout locks the front panel after it is inactive for the specified number of minutes. The range is from 0–15 minutes; 5 minutes is the default.

When locked, the front panel can be accessed only after entering the proper passcode (sequence of button presses) or by unlocking the panel using G-Ware.

12.To create a passcode for the front panel, click Clear to clear the default sequence. Then click any sequence of the five front panel buttons. Your choices will be displayed in the column on the right. When you are finished, click OK to enable your selections.

You will need to repeat these steps for all PSR1212 units on your network.

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 32

ClearOne comm PSR1212 operation manual System Configuration ~ Site Setup

Contents

PSR1212 Digital Matrix Mixer PSR1212 Installation ClearOne Part No Jan 2007Rev Table of Contents System Configuration Advanced Configuration Operation ControlAppendices 127 Technical Services Group ~ 1-800-283-5936 USA ~ Introduction Product overview New Features Professional Services Group Sales and Customer ServiceTechnical Support ClearOne Communications EuMEA GmbH Front panel UnpackingControls and Connections Rear panel Introduction ~ Controls and Connections Introduction ~ Controls and Connections Networking Expansion bus Power Equipment placementOperational Requirements Environmental Installation Hardware Setup Connector To connect the unitThree terminals Rear-panel audio contacts from left to right + positive Installation ~ Networking Units Networking UnitsExpansion bus connections To create an expansion bus network Mixer mode To select a mixer modeDevice IDs To assign device IDs Installation ~ LCD Programming LCD ProgrammingLCD menu tree Pressing Esc at the top of the tree does nothing To adjust a parameter Select PresetSystem menu Run Macro RS-232 menu Enable Modem Clear PasswordMeter menu Flow Control hardware Inputs menu Outputs menu Gain Matrix Technical Services Group ~ 1-800-283-5936 USA ~ System Configuration Ware Requirements Installing G-Ware To install G-WareCreating Floppy Disk Copies Directory To create a new site Site SetupCreating a new site Adding a PSR1212 To auto-detect unitsTo manually add units Select the PSR1212 icon and click Add Configuring Unit Properties To configure Unit Properties System Configuration ~ Site Setup Ware Screens Flow Screen Status bar Copying and pasting settingsSafety Mute Matrix Screen 20. G-Ware Matrix Screen Audio Routing Expansion bus O-Z routingProcess A-H routing Cross point attenuation System Configuration ~ Audio Routing Matrix report Inputs and Outputs Inputs Pwr Phantom Power FiltersActive Filter Type System Configuration ~ Inputs and Outputs Table View To configure filters GateActivation NOM count Manual Off deactivates the mic PA Adaptive Mode Chairman OverrideAdaptive Ambient Gate Ratio Decay Rate PA Adapt and AEC Reference To create a virtual reference Click Close to exit the window To assign a gating group To configure gating group settingsGating Group Select 36. Gain Adjustment Min/Max limits Meters 38. Inputs 9-12 Configuration window 40. Gain meters Outputs NOM Optimizing output gain structure Expansion Buses From Expansion Bus O-ZTo Expansion Bus O-Z Routing of audio to Processing Processing A-H Group Cmprs compressorEstablished only 47. Processing Filters window Phase BypassAdd Filter Remove Filter Delay Select the Bypass DelayDelay Changes you make in the distance and temperature fields 50. Process Gain adjust and meter Optimizing process gain structure Presets Creating PresetsOverview Local Preset password is set in the Unit Properties window see Preset Configuration paneAffected when the preset is run Advanced Configuration ~ Presets Assigning virtual references to the preset To create a preset Storage space Running presets Running multiple presets simultaneouslyTo run a preset using G-Ware To run a preset using front panel control Room combining example Flags to 0 which ensures Four macros one for each configuration are set up as follows To create a macro using Macro Recorder MacrosCreating macros Existing To create a macro using Macro Editor 16 Macro Name window To add or insert a command line Editing macrosTo edit a macro To delete a macro To run a macro using G-Ware To run a macro using front panel controlTo run a macro using the Select panel or Gpio Running macros Signal Generator UtilitiesTo use pink or white noise Select the PSR1212 Unit and Input Channel you want to use Document Compare Utility Operation ~ UtilitiesTo use tone To compare site files Open window Copying settings Print Preview window Print Reports Print Reports window To upgrade firmware GFirm Firmware Utility 13. Selecting baud rate To use G-Ware Switcher Ware SwitcherBefore using G-Ware Switcher Copy and paste settings Message LogMonitoring Views Gate View To configure Meter Views Meter Views Control/Status a To program control/status pinsGpio Builder Ments for use in a preset Remote BuilderXAP IR Remote Control ~ Remote Builder Select IR Remote default from the Select Remote Type list ClearOne Control PanelsControl ~ Remote Builder To program the XAP IR Remote Up to five control panels One IR remote can To program the Volume panelPanel To program the Select panel Select Panel selected in the Remote Builder Remote Modem Access Serial commandsModem password is RS-232 Port Command strings To create a command stringTo run a command string Control ~ RS-232 Port Technical Services Group ~ 1-800-283-5936 USA ~ Appendix a Specifications Appendix B Pinouts RS-232 COM DCE port pinout femaleAppendices ~ Appendix B Pinouts Pin Number Control Control/Status connectors Pin Definable Type Default DescriptionControl/Status a Port Pinout female Control/Status +5VDC, 300mA Preset select bitControl/Status B port pinout RS-485 Remote Panel a and B connectors Set connector pinoutLine connector pinout PinDescription Appendices ~ Appendix C Control Panel Connecting the Control PanelAppendix C Control Panel Control Panel Appendices ~ Appendix C Control Panel Accessory ClearOne Part Number Appendix D AccessoriesAppendices ~ Appendix D Accessories Appendix E Serial Commands Command structureConventions Example Appendices ~ Appendix E Serial Commands Groups and channelsType and device IDs Unit type Serial command error codes Error number Text message Explanation/SolutionMeter type definitions Appendices ~ Appendix E Serial PSR1212 Serial commands Command Function Selects/reports NOM setting on output Selects/reports off attenuation mode forSelects/reports signal generator activation Channels Aamb Adaptive Ambient Mode Amblvl Ambient Level AdjustAGC Automatic Gain Control Argument details Cgroup Compressor Group Select Chairo Chairman Override ModeBaud Baud Rate Compress Compressor Adjust Compsel Compression Select Decay Decay Adjust Delay Delay AdjustDelaysel Delay Select 100 Dfltm Default Meter 101Did Device ID Channel Group Filter Filter Adjust 102Examples Name Description Units FMP First Mic Priority Mode 103Filtsel Filter Select Flow Flow Control Gain Gain Adjustment 104FPP Front Panel Passcode Button assignment GHOLD- Gate Hold Time Adjust 105Gate Gate Status Example Gmode Gating Mode Gratio Gate Ratio Adjust106 Gover Gating Override Greport Gate Report Grpsel Gating Group SelectLabel Label 107 LMO Last Mic On Mode Lock Preset and Macro Lock108 LFP Lock Front Panel Lockprst Apply the lock to a preset or macro Lockpwd Set preset/macro password109 LVL Level 110 Lvlreport Level ReportLvlrrate Level Report Rate = Toggle Master Expansion Bus Master Mode MAX Maximum Gain Setting111 Macro Macro Execution/Reporting 112 Mdmode Modem ModeMIN Minimum Gain Setting Minit Modem Initialization String Minmax Minimum and Maximum Gain Setting113 Mline Mic/Line Adjust Mpass Modem Password114 Mmax Maximum Number of Microphones Mtrx Matrix Mtrxlvl Matrix Attenuation Adjustment115 NOM Number of Open Microphones Mode Offa Off Attenuation Mode116 Mute Mute PAA PA Adaptive Mode PP Phantom PowerPreset Preset Execution/Reporting 117 118 Prgstring Program StringSupported special characters String location Ramp Ramp Gain Adjustment 119Refsel PA/AEC Reference Select Name Description Unit Refset Reference channel setup Sermode Serial Mode120 Serecho Serial Echo 121 Sftymute Safety muteSiggen Signal Generator Sigtout Signal Generator Time Out 122String String Execution Tout Time Out Select Command Value Null to return value 123UID Unit ID VER Version Appendix F Warranty 124 Appendices ~ Appendix F Warranty 125 Safety Information 126Appendix G Compliance FCC Part 15 Compliance 127 Glossary 128 Glossary 129 130 131 132 133 Signal Delay Used for 134 135 136 Index 137 Frequency response Phase138 139