Gate, To configure filters, Activation | ClearOne comm PSR1212

System Configuration ~ Inputs and Outputs

35

Figure 3.27. Filter Graph window, table view

To configure filters

1.In either the graph or table view, select the filter type from the Type list.

Note that the configurable filter parameters displayed depend on the selected filter type.

2.Click Add Filter to add a filter to the graph or table.

3.Configure filter parameters using the previously described lists. If you are using the graph view, you can click on the node and drag it to the location you desire on the graph.

4.Click Close to exit.

Gate

The PSR1212 has unique gating parameters which control microphone activation. The Gate button on the selected input in Inputs 1–8 window opens the Gate configuration window where you can establish the gating parameters for the input.

Activation

There are three mic activation settings: Auto Gate, Manual On, and Manual Off.

• Auto Gate determines mic gating based on the input level and gating settings for the gating group the input is assigned to. It contributes to and is affected by all gating group settings such as NOM, chairman override, etc.

• Manual On activates the mic, provided it does not exceed max NOM

requirements of the gating group that the input is assigned to. It is included in

the NOM count.

•Manual Off deactivates the mic.

Figure 3.28. Gate window

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 41

ClearOne comm PSR1212 operation manual Gate, To configure filters, Activation, NOM count Manual Off deactivates the mic

Contents

PSR1212 Digital Matrix Mixer PSR1212 Installation ClearOne Part No Jan 2007Rev Table of Contents Advanced Configuration System Configuration Control OperationAppendices 127 Technical Services Group ~ 1-800-283-5936 USA ~ Product overview Introduction New Features Sales and Customer Service Professional Services GroupTechnical Support ClearOne Communications EuMEA GmbH Front panel UnpackingControls and Connections Introduction ~ Controls and Connections Rear panel Introduction ~ Controls and Connections Expansion bus Networking Equipment placement PowerOperational Requirements Environmental Hardware Setup Installation To connect the unit ConnectorThree terminals Rear-panel audio contacts from left to right + positive Networking Units Installation ~ Networking UnitsExpansion bus connections To create an expansion bus network To select a mixer mode Mixer modeDevice IDs To assign device IDs LCD Programming Installation ~ LCD ProgrammingLCD menu tree Pressing Esc at the top of the tree does nothing Select Preset To adjust a parameterSystem menu Run Macro RS-232 menu Clear Password Enable ModemMeter menu Flow Control hardware Inputs menu Gain Outputs menu Matrix Technical Services Group ~ 1-800-283-5936 USA ~ Ware Requirements System Configuration To install G-Ware Installing G-WareCreating Floppy Disk Copies Directory To create a new site Site SetupCreating a new site To auto-detect units Adding a PSR1212To manually add units Select the PSR1212 icon and click Add To configure Unit Properties Configuring Unit Properties System Configuration ~ Site Setup Flow Screen Ware Screens Status bar Copying and pasting settingsSafety Mute 20. G-Ware Matrix Screen Matrix Screen Expansion bus O-Z routing Audio RoutingProcess A-H routing Cross point attenuation Matrix report System Configuration ~ Audio Routing Inputs Inputs and Outputs Filters Pwr Phantom PowerActive Filter Type Table View System Configuration ~ Inputs and Outputs Gate To configure filtersActivation NOM count Manual Off deactivates the mic Chairman Override PA Adaptive ModeAdaptive Ambient Gate Ratio PA Adapt and AEC Reference Decay Rate Click Close to exit the window To create a virtual reference To assign a gating group To configure gating group settingsGating Group Select Min/Max limits 36. Gain Adjustment Meters 38. Inputs 9-12 Configuration window 40. Gain meters NOM Outputs Optimizing output gain structure From Expansion Bus O-Z Expansion BusesTo Expansion Bus O-Z Routing of audio to Processing A-H Processing Group Cmprs compressorEstablished only 47. Processing Filters window Bypass PhaseAdd Filter Remove Filter Select the Bypass Delay DelayDelay Changes you make in the distance and temperature fields Optimizing process gain structure 50. Process Gain adjust and meter Creating Presets PresetsOverview Local Preset password is set in the Unit Properties window see Preset Configuration paneAffected when the preset is run Advanced Configuration ~ Presets Assigning virtual references to the preset Storage space To create a preset Running multiple presets simultaneously Running presetsTo run a preset using G-Ware To run a preset using front panel control Flags to 0 which ensures Room combining example Four macros one for each configuration are set up as follows Macros To create a macro using Macro RecorderCreating macros Existing 16 Macro Name window To create a macro using Macro Editor Editing macros To add or insert a command lineTo edit a macro To delete a macro To run a macro using front panel control To run a macro using G-WareTo run a macro using the Select panel or Gpio Running macros Utilities Signal GeneratorTo use pink or white noise Select the PSR1212 Unit and Input Channel you want to use Operation ~ Utilities Document Compare UtilityTo use tone To compare site files Open window Print Preview window Copying settings Print Reports window Print Reports GFirm Firmware Utility To upgrade firmware 13. Selecting baud rate To use G-Ware Switcher Ware SwitcherBefore using G-Ware Switcher Message Log Copy and paste settingsMonitoring Views Gate View Meter Views To configure Meter Views Control/Status a To program control/status pinsGpio Builder Remote Builder Ments for use in a presetXAP IR Remote Control ~ Remote Builder ClearOne Control Panels Select IR Remote default from the Select Remote Type listControl ~ Remote Builder To program the XAP IR Remote Up to five control panels One IR remote can To program the Volume panelPanel Select Panel selected in the Remote Builder To program the Select panel Serial commands Remote Modem AccessModem password is RS-232 Port To create a command string Command stringsTo run a command string Control ~ RS-232 Port Technical Services Group ~ 1-800-283-5936 USA ~ Appendix a Specifications RS-232 COM DCE port pinout female Appendix B PinoutsAppendices ~ Appendix B Pinouts Pin Number Control Pin Definable Type Default Description Control/Status connectorsControl/Status a Port Pinout female Control/Status +5VDC, 300mA Preset select bitControl/Status B port pinout Set connector pinout RS-485 Remote Panel a and B connectorsLine connector pinout PinDescription Appendices ~ Appendix C Control Panel Connecting the Control PanelAppendix C Control Panel Control Panel Appendices ~ Appendix C Control Panel Accessory ClearOne Part Number Appendix D AccessoriesAppendices ~ Appendix D Accessories Command structure Appendix E Serial CommandsConventions Example Groups and channels Appendices ~ Appendix E Serial CommandsType and device IDs Unit type Error number Text message Explanation/Solution Serial command error codesMeter type definitions Appendices ~ Appendix E Serial Command Function PSR1212 Serial commands Selects/reports off attenuation mode for Selects/reports NOM setting on outputSelects/reports signal generator activation Channels Amblvl Ambient Level Adjust Aamb Adaptive Ambient ModeAGC Automatic Gain Control Argument details Cgroup Compressor Group Select Chairo Chairman Override ModeBaud Baud Rate Compsel Compression Select Compress Compressor Adjust Delay Delay Adjust Decay Decay AdjustDelaysel Delay Select 100 101 Dfltm Default MeterDid Device ID Channel Group 102 Filter Filter AdjustExamples Name Description Units 103 FMP First Mic Priority ModeFiltsel Filter Select Flow Flow Control 104 Gain Gain AdjustmentFPP Front Panel Passcode Button assignment 105 GHOLD- Gate Hold Time AdjustGate Gate Status Example Gratio Gate Ratio Adjust Gmode Gating Mode106 Gover Gating Override Grpsel Gating Group Select Greport Gate ReportLabel Label 107 Lock Preset and Macro Lock LMO Last Mic On Mode108 LFP Lock Front Panel Lockpwd Set preset/macro password Lockprst Apply the lock to a preset or macro109 LVL Level Lvlreport Level Report 110Lvlrrate Level Report Rate = Toggle MAX Maximum Gain Setting Master Expansion Bus Master Mode111 Macro Macro Execution/Reporting 112 Mdmode Modem ModeMIN Minimum Gain Setting Minit Modem Initialization String Minmax Minimum and Maximum Gain Setting113 Mpass Modem Password Mline Mic/Line Adjust114 Mmax Maximum Number of Microphones Mtrx Matrix Mtrxlvl Matrix Attenuation Adjustment115 Offa Off Attenuation Mode NOM Number of Open Microphones Mode116 Mute Mute PP Phantom Power PAA PA Adaptive ModePreset Preset Execution/Reporting 117 Prgstring Program String 118Supported special characters String location 119 Ramp Ramp Gain AdjustmentRefsel PA/AEC Reference Select Name Description Unit Sermode Serial Mode Refset Reference channel setup120 Serecho Serial Echo 121 Sftymute Safety muteSiggen Signal Generator 122 Sigtout Signal Generator Time OutString String Execution Tout Time Out Select 123 Command Value Null to return valueUID Unit ID VER Version 124 Appendix F Warranty 125 Appendices ~ Appendix F Warranty 126 Safety InformationAppendix G Compliance FCC Part 15 Compliance Glossary 127 Glossary 128 129 130 131 132 133 134 Signal Delay Used for 135 Index 136 137 Frequency response Phase138 139