Rear panel | ClearOne comm PSR1212 instruction

Introduction ~ Controls and Connections

5

C.s/tThese buttons scroll up and down through vertical programming options within a specific PSR1212 programming parameter or increases/decreases a numeric value.

D.Esc. This button steps you out of a selected parameter or moves you up one level in the menu. When a parameter has been displayed with the arrow buttons [C], you can select it with the Enter button [B] to modify it. Then, you can step out of the menu with the Esc button.

E.LED meter. This assignable, peak-level LED bar meter is used to display the audio level of an input, output, or processing channel of the PSR1212.

F.Meter. Takes you directly to the Meter branch of the PSR1212’s LCD menu tree.

G.LED 1–8.These LEDs indicate Inputs 1–8 gate status.

Rear panel

Expansion Bus
In	Out

Figure 1.3. Rear panel connections

A.Power. This power module accommodates power ranging from 100–240VAC, 50/60Hz. The module uses an IEC-type connector. No switching is required.

B.Inputs 1–8.These Phoenix block connectors are for connection of eight mic-level or line-level (selectable) inputs. These connectors are typically used for mics, but can be configured for use with VCRs, CD players, etc. These inputs can be mixed in any gated or non-gated combination and routed to any of the 12 outputs. Default input level is -55dBu. For more information about input adjustments, see page 32. For electrical specifications, see Appendix A: Specifications.

C.RS-485 Remote Panel A/B Port. These four-pin Phoenix connector ports allow you to control the PSR1212 with the ClearOne Control Panel or XAP IR Remote Control.

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 11

ClearOne comm PSR1212 operation manual Rear panel, Introduction ~ Controls and Connections

Contents

PSR1212 Digital Matrix Mixer PSR1212 Installation ClearOne Part No Jan 2007Rev Table of Contents Advanced Configuration System Configuration 127 OperationControl Appendices Technical Services Group ~ 1-800-283-5936 USA ~ Product overview Introduction New Features ClearOne Communications EuMEA GmbH Professional Services GroupSales and Customer Service Technical Support Front panel UnpackingControls and Connections Introduction ~ Controls and Connections Rear panel Introduction ~ Controls and Connections Expansion bus Networking Environmental PowerEquipment placement Operational Requirements Hardware Setup Installation Rear-panel audio contacts from left to right + positive ConnectorTo connect the unit Three terminals To create an expansion bus network Installation ~ Networking UnitsNetworking Units Expansion bus connections To assign device IDs Mixer modeTo select a mixer mode Device IDs Pressing Esc at the top of the tree does nothing Installation ~ LCD ProgrammingLCD Programming LCD menu tree Run Macro To adjust a parameterSelect Preset System menu RS-232 menu Flow Control hardware Enable ModemClear Password Meter menu Inputs menu Gain Outputs menu Matrix Technical Services Group ~ 1-800-283-5936 USA ~ Ware Requirements System Configuration Directory Installing G-WareTo install G-Ware Creating Floppy Disk Copies To create a new site Site SetupCreating a new site Select the PSR1212 icon and click Add Adding a PSR1212To auto-detect units To manually add units To configure Unit Properties Configuring Unit Properties System Configuration ~ Site Setup Flow Screen Ware Screens Status bar Copying and pasting settingsSafety Mute 20. G-Ware Matrix Screen Matrix Screen Cross point attenuation Audio RoutingExpansion bus O-Z routing Process A-H routing Matrix report System Configuration ~ Audio Routing Inputs Inputs and Outputs Type Pwr Phantom PowerFilters Active Filter Table View System Configuration ~ Inputs and Outputs NOM count Manual Off deactivates the mic To configure filtersGate Activation Gate Ratio PA Adaptive ModeChairman Override Adaptive Ambient PA Adapt and AEC Reference Decay Rate Click Close to exit the window To create a virtual reference To assign a gating group To configure gating group settingsGating Group Select Min/Max limits 36. Gain Adjustment Meters 38. Inputs 9-12 Configuration window 40. Gain meters NOM Outputs Optimizing output gain structure Routing of audio to Expansion BusesFrom Expansion Bus O-Z To Expansion Bus O-Z Processing A-H Processing Group Cmprs compressorEstablished only 47. Processing Filters window Remove Filter PhaseBypass Add Filter Changes you make in the distance and temperature fields DelaySelect the Bypass Delay Delay Optimizing process gain structure 50. Process Gain adjust and meter Local PresetsCreating Presets Overview Preset password is set in the Unit Properties window see Preset Configuration paneAffected when the preset is run Advanced Configuration ~ Presets Assigning virtual references to the preset Storage space To create a preset To run a preset using front panel control Running presetsRunning multiple presets simultaneously To run a preset using G-Ware Flags to 0 which ensures Room combining example Four macros one for each configuration are set up as follows Existing To create a macro using Macro RecorderMacros Creating macros 16 Macro Name window To create a macro using Macro Editor To delete a macro To add or insert a command lineEditing macros To edit a macro Running macros To run a macro using G-WareTo run a macro using front panel control To run a macro using the Select panel or Gpio Select the PSR1212 Unit and Input Channel you want to use Signal GeneratorUtilities To use pink or white noise To compare site files Document Compare UtilityOperation ~ Utilities To use tone Open window Print Preview window Copying settings Print Reports window Print Reports GFirm Firmware Utility To upgrade firmware 13. Selecting baud rate To use G-Ware Switcher Ware SwitcherBefore using G-Ware Switcher Gate View Copy and paste settingsMessage Log Monitoring Views Meter Views To configure Meter Views Control/Status a To program control/status pinsGpio Builder Control ~ Remote Builder Ments for use in a presetRemote Builder XAP IR Remote Up to five control panels Select IR Remote default from the Select Remote Type listClearOne Control Panels Control ~ Remote Builder To program the XAP IR Remote One IR remote can To program the Volume panelPanel Select Panel selected in the Remote Builder To program the Select panel RS-232 Port Remote Modem AccessSerial commands Modem password is Control ~ RS-232 Port Command stringsTo create a command string To run a command string Technical Services Group ~ 1-800-283-5936 USA ~ Appendix a Specifications Pin Number Control Appendix B PinoutsRS-232 COM DCE port pinout female Appendices ~ Appendix B Pinouts Control/Status Control/Status connectorsPin Definable Type Default Description Control/Status a Port Pinout female +5VDC, 300mA Preset select bitControl/Status B port pinout PinDescription RS-485 Remote Panel a and B connectorsSet connector pinout Line connector pinout Appendices ~ Appendix C Control Panel Connecting the Control PanelAppendix C Control Panel Control Panel Appendices ~ Appendix C Control Panel Accessory ClearOne Part Number Appendix D AccessoriesAppendices ~ Appendix D Accessories Example Appendix E Serial CommandsCommand structure Conventions Unit type Appendices ~ Appendix E Serial CommandsGroups and channels Type and device IDs Appendices ~ Appendix E Serial Serial command error codesError number Text message Explanation/Solution Meter type definitions Command Function PSR1212 Serial commands Channels Selects/reports NOM setting on outputSelects/reports off attenuation mode for Selects/reports signal generator activation Argument details Aamb Adaptive Ambient ModeAmblvl Ambient Level Adjust AGC Automatic Gain Control Cgroup Compressor Group Select Chairo Chairman Override ModeBaud Baud Rate Compsel Compression Select Compress Compressor Adjust 100 Decay Decay AdjustDelay Delay Adjust Delaysel Delay Select Channel Group Dfltm Default Meter101 Did Device ID Name Description Units Filter Filter Adjust102 Examples Flow Flow Control FMP First Mic Priority Mode103 Filtsel Filter Select Button assignment Gain Gain Adjustment104 FPP Front Panel Passcode Example GHOLD- Gate Hold Time Adjust105 Gate Gate Status Gover Gating Override Gmode Gating ModeGratio Gate Ratio Adjust 106 107 Greport Gate ReportGrpsel Gating Group Select Label Label LFP Lock Front Panel LMO Last Mic On ModeLock Preset and Macro Lock 108 LVL Level Lockprst Apply the lock to a preset or macroLockpwd Set preset/macro password 109 = Toggle 110Lvlreport Level Report Lvlrrate Level Report Rate Macro Macro Execution/Reporting Master Expansion Bus Master ModeMAX Maximum Gain Setting 111 112 Mdmode Modem ModeMIN Minimum Gain Setting Minit Modem Initialization String Minmax Minimum and Maximum Gain Setting113 Mmax Maximum Number of Microphones Mline Mic/Line AdjustMpass Modem Password 114 Mtrx Matrix Mtrxlvl Matrix Attenuation Adjustment115 Mute Mute NOM Number of Open Microphones ModeOffa Off Attenuation Mode 116 117 PAA PA Adaptive ModePP Phantom Power Preset Preset Execution/Reporting String location 118Prgstring Program String Supported special characters Name Description Unit Ramp Ramp Gain Adjustment119 Refsel PA/AEC Reference Select Serecho Serial Echo Refset Reference channel setupSermode Serial Mode 120 121 Sftymute Safety muteSiggen Signal Generator Tout Time Out Select Sigtout Signal Generator Time Out122 String String Execution VER Version Command Value Null to return value123 UID Unit ID 124 Appendix F Warranty 125 Appendices ~ Appendix F Warranty FCC Part 15 Compliance Safety Information126 Appendix G Compliance Glossary 127 Glossary 128 129 130 131 132 133 134 Signal Delay Used for 135 Index 136 137 Frequency response Phase138 139