Register Function Range Units Saved Default | Digi W specs

Register		Function	Range	Units	Saved	Default
S13	Reserved		-	-		-
	General Bit Mapped Options Status
	Indicates the status of command options.
	Default:138 (8Ah) (10001010b)
	Bit 0This bit is ignored.
	Bit 1Command echo (En)
	0	=Disabled (E0)
	1	=Enabled (E1) (Default.)
	Bit 2Quiet mode (Qn)
	0	=Send result codes (Q0) (Default.)
	1	=Do not send result codes (Q1)				138
S14	Bit 3Result codes (Vn)				*	138
S14	Bit 3Result codes (Vn)				*	(8Ah)
	0	=Numeric (V0)				(8Ah)
	0	=Numeric (V0)
	1	=Verbose (V1) (Default.)
	Bit 4Reserved
	Bit 5Tone (T)/Pulse (P)
	0	=Tone (T) (Default.)
	1	=Pulse (P)
	Bit 6Reserved
	Bit 7Originate/Answer
	0	=Answer
	1	=Originate (Default.)
S15	Reserved		-	-		-
S16	Accepted but ignored.		-	-		0
S17	Reserved		-		-	-
S18	Accepted but ignored.		0-255	s	*	0
S19	Accepted but ignored.		-	-		0
S20	Accepted but ignored.		0-255	-	*	0

Chapter 9 Modem Emulation

43

Image 43

Digi W manual Register Function Range Units Saved Default

Contents

Digi TS W Family 9000329B Chapter Introduction Chapter Configuring WirelessConfiguring the IP Address N t e n t s Chapter Configuring Autoconnection Setting Up RealPortConfiguring the Serial Ports Chapter Configuring PPP Configuring Security Features Configuring IP Routing Configuring Users Configuring the Digi Device for IAIndustrial AutomationConfiguring DNS Configuring Snmp Reference and Certifications Configuring Power Over the Serial Ports Contents T r o d u c t i o n Setup Overview Other Documents in the Library About Entering Commands on the Command LineSupported Devices About This Guide About Configuration Methods Configuration Prerequisites N f i g u r i n g W i r e l e s s Configuration Considerations Select Discover Digi Device from the CD Configuring Wireless Configuring Wireless Configuring Wireless Configuring Wireless N f i g u r i n g t h e I P a d d r e s s Options for Configuring the IP Address and Mask Configuring the IP Address Using ARP-Ping Configuring the Ethernet Interface from the Command Line Configuring an IP Address using Dhcp and Rarp About RealPort T t i n g U p R e a l P o r t Setting Up RealPort Configuring the Serial Port Settings with the Web Interface Options for Configuring the Serial Ports Configuring the Serial Port Settings from the Command Line N f i g u r i n g P P P Configuring Inbound PPP Connections Configuring Outbound PPP Connections Command Line Configuring Inbound PPP Connections Example Procedure Sample Use the following table for additional configurations Configuring PPP Modem Emulation Digi One TS and PortServer TS 2/4 MEI only D e m E m u l a t i o nCommon User Scenarios Serial Device Digi Device Server Modem Emulation Cable Signals Application AT Com Digi Device Server Response Mand Originating, Answering, and Disconnecting Calls Server. P represents a one second pause Code Modem Emulation AT Command Set Function Result ATP Function Result ATXn Accepted but ignored There is no Nvram support currently AT+MS Ascii Registers Function Range Units Saved Default Register Function Range Units Saved Default Register Function Range Units Saved Default 17 11h =XON/XOFF &K4 Result Codes Short Long Form Modem Emulation N f i g u r i n g a u t o c o n n e c t i o n Configuring a Port for Autoconnection Web InterfaceCommands for Configuring Autoconnection by Port or by User Configuring a User for Autoconnection Web Interface Click Change Profile Configuring TCP Socket CommunicationConfiguring UDP Multicast Click Serial Ports Click Change Profile and select UDP Socket Configuring Autoconnection N f i g u r i n g I P R o u t i n g Configuring Static Routes Configuring Dynamic Routes Using RIP Configuring Proxy ARP Configuring IP Routing Controlling Access to Inbound Ports Controlling Access to the ConfigurationN f i g u r i n g S e c u r i t y F e a t u r e s Controlling Access to the Command Line Controlling Access to Outbound Ports Configuring SSH Version 2 for Secure Communication Issuing User PasswordsDevice Required Hardware Firmware Http Controlling Access to Services Snmp SSH Configuring Security Features Configuring the User-Defined Protocol Configuring Modbus Configuring the Digi Device for IA Industrial Automation About the Domain Name System N f i g u r i n g D N S Configuration Procedures About Snmp and the Device Server Agent N f i g u r i n g S N M P MIB Configuration Procedure Web Interface N f i g u r i n g U s e r s About Configuring UsersCommon User Features Feature Description Set user Field Commands for Configuring a User Configuring a User Web InterfaceClick New User Upgrading the Firmware Copying the Configuration to and from a Remote Host Resetting Device Server Configuration to Defaults Commands for Resetting the Configuration to Defaults Managing the OS and Configuration Configuring RI Power Serial Power Feature Configuring DTR Power DTR on DTR OFF Serial Power Table Configuring Power Over the Serial Ports Interpreting the LEDs F e r e n c e a n d C e r t i f i c a t i o n sColor State Indicates RJ-45 Pinouts EIA-232 EIA-422/485 EIA-485 Half Full-Duplex Environmental Certifications Digi Contact Information Digi Contacts Reference and Certifications