Click Change Profile and select UDP Socket | Digi W instruction

Procedure for Configuring Inbound or Outbound Socket Communication

1.Access the web interface by entering the device server IP address in a browser’s URL window.

2.Log on to the Digi One/PortServer TS as root. The default password is dbps.

3.Click Serial Ports.

4.Click the port number you want to configure.

5.Click Change Profile and select UDP Socket

Note: The serial parameters for two connecting devices must match meaning if one device is set for 9600 bps, the other device must be set for the same rate.

6.Fill in the requested information and click Apply to save the settings.

7.Repeat these steps until you have added the necessary destinations. Use the context sensitive Help for additional information.

Chapter 10 Configuring Autoconnection

51

Image 51

Contents

Digi TS W Family 9000329B Chapter Introduction Chapter Configuring WirelessConfiguring the IP Address N t e n t s Chapter Configuring Autoconnection Setting Up RealPortConfiguring the Serial Ports Chapter Configuring PPP Configuring Security Features Configuring IP Routing Configuring Users Configuring the Digi Device for IAIndustrial AutomationConfiguring DNS Configuring Snmp Reference and Certifications Configuring Power Over the Serial Ports Contents T r o d u c t i o n Setup Overview Other Documents in the Library About Entering Commands on the Command LineSupported Devices About This Guide About Configuration Methods Configuration Prerequisites N f i g u r i n g W i r e l e s s Configuration Considerations Select Discover Digi Device from the CD Configuring Wireless Configuring Wireless Configuring Wireless Configuring Wireless N f i g u r i n g t h e I P a d d r e s s Options for Configuring the IP Address and Mask Configuring the IP Address Using ARP-Ping Configuring the Ethernet Interface from the Command Line Configuring an IP Address using Dhcp and Rarp About RealPort T t i n g U p R e a l P o r t Setting Up RealPort Configuring the Serial Port Settings with the Web Interface Options for Configuring the Serial Ports Configuring the Serial Port Settings from the Command Line N f i g u r i n g P P P Configuring Inbound PPP Connections Configuring Outbound PPP Connections Command Line Configuring Inbound PPP Connections Example Procedure Sample Use the following table for additional configurations Configuring PPP D e m E m u l a t i o n Modem Emulation Digi One TS and PortServer TS 2/4 MEI onlyCommon User Scenarios Serial Device Digi Device Server Modem Emulation Cable Signals Application AT Com Digi Device Server Response Mand Originating, Answering, and Disconnecting Calls Server. P represents a one second pause Code Modem Emulation AT Command Set Function Result ATP Function Result ATXn Accepted but ignored There is no Nvram support currently AT+MS Ascii Registers Function Range Units Saved Default Register Function Range Units Saved Default Register Function Range Units Saved Default 17 11h =XON/XOFF &K4 Result Codes Short Long Form Modem Emulation N f i g u r i n g a u t o c o n n e c t i o n Configuring a Port for Autoconnection Web InterfaceCommands for Configuring Autoconnection by Port or by User Configuring a User for Autoconnection Web Interface Click Change Profile Configuring TCP Socket CommunicationConfiguring UDP Multicast Click Serial Ports Click Change Profile and select UDP Socket Configuring Autoconnection N f i g u r i n g I P R o u t i n g Configuring Static Routes Configuring Dynamic Routes Using RIP Configuring Proxy ARP Configuring IP Routing Controlling Access to the Configuration Controlling Access to Inbound PortsN f i g u r i n g S e c u r i t y F e a t u r e s Controlling Access to the Command Line Controlling Access to Outbound Ports Issuing User Passwords Configuring SSH Version 2 for Secure CommunicationDevice Required Hardware Firmware Http Controlling Access to Services Snmp SSH Configuring Security Features Configuring the User-Defined Protocol Configuring Modbus Configuring the Digi Device for IA Industrial Automation About the Domain Name System N f i g u r i n g D N S Configuration Procedures About Snmp and the Device Server Agent N f i g u r i n g S N M P MIB Configuration Procedure Web Interface N f i g u r i n g U s e r s About Configuring UsersCommon User Features Feature Description Set user Field Configuring a User Web Interface Commands for Configuring a UserClick New User Upgrading the Firmware Copying the Configuration to and from a Remote Host Resetting Device Server Configuration to Defaults Commands for Resetting the Configuration to Defaults Managing the OS and Configuration Configuring RI Power Serial Power Feature Configuring DTR Power DTR on DTR OFF Serial Power Table Configuring Power Over the Serial Ports F e r e n c e a n d C e r t i f i c a t i o n s Interpreting the LEDsColor State Indicates RJ-45 Pinouts EIA-232 EIA-422/485 EIA-485 Half Full-Duplex Environmental Certifications Digi Contact Information Digi Contacts Reference and Certifications