Result Codes Short Long Form | Digi W specification

Register		Function			Range		Units		Saved		Default
											10
											(Coun-
S91	Accepted but ignored.				0-15		dBm				try
											depen-
											dent)
											10
S92	Accepted but ignored.				0-15		dBm				(Country
S92	Accepted but ignored.				0-15		dBm				depen-
											depen-
											dent)
S95	Accepted but ignored.				-		-		*		0
	* Register value may be stored in one of two user profiles with the &W command.
Result Codes

Short	Long Form		Short	Long Form			Short			Long Form

0	OK		13	CONNECT			84			CONNECT
0	OK		13	7200			84			33600
				7200						33600
1	CONNECT		14	CONNECT			91			CONNECT
1	CONNECT		14	12000			91			31200
				12000						31200
2	RING		15	CONNECT			165			CONNECT
2	RING		15	14400			165			32000
				14400						32000
3	NO CARRIER		16	CONNECT			166			CONNECT
3	NO CARRIER		16	19200			166			34000
				19200						34000
4	ERROR		17	CONNECT			167			CONNECT
4	ERROR		17	38400			167			36000
				38400						36000
5	CONNECT		18	CONNECT			168			CONNECT
5	1200		18	57600			168			38000
	1200			57600						38000
6	NO DIALTONE		19	CONNECT			169			CONNECT
6	NO DIALTONE		19	115200			169			40000
				115200						40000
7	BUSY		20	CONNECT			170			CONNECT
7	BUSY		20	230400			170			42000
				230400						42000
8	NO ANSWER		59	CONNECT			171			CONNECT
8	NO ANSWER		59	16800			171			44000
				16800						44000
9	CONNECT		61	CONNECT			172			CONNECT
9	0600		61	21600			172			46000
	0600			21600						46000
10	CONNECT		62	CONNECT			173			CONNECT
10	2400		62	24000			173			48000
	2400			24000						48000
11	CONNECT		63	CONNECT			174			CONNECT
11	4800		63	26400			174			50000
	4800			26400						50000
12	CONNECT		64	CONNECT
12	9600		64	28800
	9600			28800

Chapter 9 Modem Emulation

47

Image 47

Digi W manual Result Codes Short Long Form

Contents

Digi TS W Family 9000329B Chapter Introduction Chapter Configuring WirelessConfiguring the IP Address N t e n t s Chapter Configuring Autoconnection Setting Up RealPortConfiguring the Serial Ports Chapter Configuring PPP Configuring Security Features Configuring IP Routing Configuring Users Configuring the Digi Device for IAIndustrial AutomationConfiguring DNS Configuring Snmp Reference and Certifications Configuring Power Over the Serial Ports Contents T r o d u c t i o n Setup Overview Other Documents in the Library About Entering Commands on the Command LineSupported Devices About This Guide About Configuration Methods Configuration Prerequisites N f i g u r i n g W i r e l e s s Configuration Considerations Select Discover Digi Device from the CD Configuring Wireless Configuring Wireless Configuring Wireless Configuring Wireless N f i g u r i n g t h e I P a d d r e s s Options for Configuring the IP Address and Mask Configuring the IP Address Using ARP-Ping Configuring the Ethernet Interface from the Command Line Configuring an IP Address using Dhcp and Rarp About RealPort T t i n g U p R e a l P o r t Setting Up RealPort Configuring the Serial Port Settings with the Web Interface Options for Configuring the Serial Ports Configuring the Serial Port Settings from the Command Line N f i g u r i n g P P P Configuring Inbound PPP Connections Configuring Outbound PPP Connections Command Line Configuring Inbound PPP Connections Example Procedure Sample Use the following table for additional configurations Configuring PPP Common User Scenarios D e m E m u l a t i o nModem Emulation Digi One TS and PortServer TS 2/4 MEI only Serial Device Digi Device Server Modem Emulation Cable Signals Application AT Com Digi Device Server Response Mand Originating, Answering, and Disconnecting Calls Server. P represents a one second pause Code Modem Emulation AT Command Set Function Result ATP Function Result ATXn Accepted but ignored There is no Nvram support currently AT+MS Ascii Registers Function Range Units Saved Default Register Function Range Units Saved Default Register Function Range Units Saved Default 17 11h =XON/XOFF &K4 Result Codes Short Long Form Modem Emulation N f i g u r i n g a u t o c o n n e c t i o n Configuring a Port for Autoconnection Web InterfaceCommands for Configuring Autoconnection by Port or by User Configuring a User for Autoconnection Web Interface Click Change Profile Configuring TCP Socket CommunicationConfiguring UDP Multicast Click Serial Ports Click Change Profile and select UDP Socket Configuring Autoconnection N f i g u r i n g I P R o u t i n g Configuring Static Routes Configuring Dynamic Routes Using RIP Configuring Proxy ARP Configuring IP Routing N f i g u r i n g S e c u r i t y F e a t u r e s Controlling Access to the ConfigurationControlling Access to Inbound Ports Controlling Access to the Command Line Controlling Access to Outbound Ports Device Required Hardware Firmware Issuing User PasswordsConfiguring SSH Version 2 for Secure Communication Http Controlling Access to Services Snmp SSH Configuring Security Features Configuring the User-Defined Protocol Configuring Modbus Configuring the Digi Device for IA Industrial Automation About the Domain Name System N f i g u r i n g D N S Configuration Procedures About Snmp and the Device Server Agent N f i g u r i n g S N M P MIB Configuration Procedure Web Interface N f i g u r i n g U s e r s About Configuring UsersCommon User Features Feature Description Set user Field Click New User Configuring a User Web InterfaceCommands for Configuring a User Upgrading the Firmware Copying the Configuration to and from a Remote Host Resetting Device Server Configuration to Defaults Commands for Resetting the Configuration to Defaults Managing the OS and Configuration Configuring RI Power Serial Power Feature Configuring DTR Power DTR on DTR OFF Serial Power Table Configuring Power Over the Serial Ports Color State Indicates F e r e n c e a n d C e r t i f i c a t i o n sInterpreting the LEDs RJ-45 Pinouts EIA-232 EIA-422/485 EIA-485 Half Full-Duplex Environmental Certifications Digi Contact Information Digi Contacts Reference and Certifications