Select Discover Digi Device from the CD | Digi W guide

2.Insert CD, the wizard will automatically pop up. Follow wizard either for Microsoft Windows or Unix to configure the device. If you do not want to use the wizard click Cancel and follow the remaining procedure to set up the IP address and configure the device through the web interface.

3.Select Discover Digi Device (from the CD).

4.Select the wireless device and assign the IP address.

5.Click Set IP.

6.Enter the IP address, Subnet, and Gateway mask and click OK.

7.Select the device and click Configure to launch your browser.

8.Enter the username root and password dbps and click OK.

14	Chapter 4 Configuring Wireless

Image 14

Digi W manual Select Discover Digi Device from the CD

Contents

Digi TS W Family 9000329B N t e n t s Chapter Configuring WirelessConfiguring the IP Address Chapter Introduction Chapter Configuring PPP Setting Up RealPortConfiguring the Serial Ports Chapter Configuring Autoconnection Configuring IP Routing Configuring Security Features Configuring Snmp Configuring the Digi Device for IAIndustrial AutomationConfiguring DNS Configuring Users Configuring Power Over the Serial Ports Reference and Certifications Contents Setup Overview T r o d u c t i o n About This Guide About Entering Commands on the Command LineSupported Devices Other Documents in the Library About Configuration Methods Configuration Prerequisites Configuration Considerations N f i g u r i n g W i r e l e s s Select Discover Digi Device from the CD Configuring Wireless Configuring Wireless Configuring Wireless Configuring Wireless Options for Configuring the IP Address and Mask N f i g u r i n g t h e I P a d d r e s s Configuring the IP Address Using ARP-Ping Configuring the Ethernet Interface from the Command Line Configuring an IP Address using Dhcp and Rarp T t i n g U p R e a l P o r t About RealPort Setting Up RealPort Options for Configuring the Serial Ports Configuring the Serial Port Settings with the Web Interface Configuring the Serial Port Settings from the Command Line Configuring Inbound PPP Connections N f i g u r i n g P P P Configuring Inbound PPP Connections Example Configuring Outbound PPP Connections Command Line Procedure Sample Use the following table for additional configurations Configuring PPP Common User Scenarios D e m E m u l a t i o nModem Emulation Digi One TS and PortServer TS 2/4 MEI only Modem Emulation Cable Signals Serial Device Digi Device Server Originating, Answering, and Disconnecting Calls Application AT Com Digi Device Server Response Mand Server. P represents a one second pause Modem Emulation AT Command Set Function Result Code Function Result ATP ATXn Accepted but ignored There is no Nvram support currently AT+MS Registers Function Range Units Saved Default Ascii Register Function Range Units Saved Default Register Function Range Units Saved Default 17 11h =XON/XOFF &K4 Result Codes Short Long Form Modem Emulation Configuring a User for Autoconnection Web Interface Configuring a Port for Autoconnection Web InterfaceCommands for Configuring Autoconnection by Port or by User N f i g u r i n g a u t o c o n n e c t i o n Click Serial Ports Configuring TCP Socket CommunicationConfiguring UDP Multicast Click Change Profile Click Change Profile and select UDP Socket Configuring Autoconnection Configuring Static Routes N f i g u r i n g I P R o u t i n g Configuring Dynamic Routes Using RIP Configuring Proxy ARP Configuring IP Routing N f i g u r i n g S e c u r i t y F e a t u r e s Controlling Access to the ConfigurationControlling Access to Inbound Ports Controlling Access to Outbound Ports Controlling Access to the Command Line Device Required Hardware Firmware Issuing User PasswordsConfiguring SSH Version 2 for Secure Communication Controlling Access to Services Http Snmp SSH Configuring Security Features Configuring Modbus Configuring the User-Defined Protocol Configuring the Digi Device for IA Industrial Automation N f i g u r i n g D N S About the Domain Name System Configuration Procedures N f i g u r i n g S N M P About Snmp and the Device Server Agent Configuration Procedure Web Interface MIB Feature Description Set user Field About Configuring UsersCommon User Features N f i g u r i n g U s e r s Click New User Configuring a User Web InterfaceCommands for Configuring a User Copying the Configuration to and from a Remote Host Upgrading the Firmware Resetting Device Server Configuration to Defaults Commands for Resetting the Configuration to Defaults Managing the OS and Configuration Serial Power Feature Configuring RI Power Configuring DTR Power Serial Power Table DTR on DTR OFF Configuring Power Over the Serial Ports Color State Indicates F e r e n c e a n d C e r t i f i c a t i o n sInterpreting the LEDs RJ-45 Pinouts EIA-232 EIA-422/485 EIA-485 Half Full-Duplex Certifications Environmental Digi Contact Information Digi Contacts Reference and Certifications