=XON/XOFF &K4 | Digi W instruction

	Register		Function	Range	Units	Saved	Default
		General Bit Mapped Options Status
		Telnet support for modem emulation.
		Default:0
		Bit 0-1 Send TCP transmit data timer
		0 = 100ms
		1 = 200 ms
		2 = 300 ms
		3 = 500 ms
		Bits 2-3 Service TCP transmit data watermark
		0	= 256
		1	= 512
		2	=768
	S37	3	=1024	-	-	*	0
		Bits 4-5 Service TCP receive data watermark
		0	= 256
		1	= 512
		2	=768
		3	=1024
		Bits 6-7 Telnet support (RFC 2217)
		0	= Disabled
		1	= Receive Telnet support enabled
		2	= Transmit Telnet support enabled
		3	= Receive and Transmit Telnet support
		enabled

	S38	Accepted but ignored.		0-255	s		20
		Flow Control Bit Mapped Options Status
		Default:3 (00000011b)
		Bits 0-2Status of command options
		0	=No flow control
	S39	3	=RTS/CTS (&K3) (Default.)	-	-	*	3
		4	=XON/XOFF (&K4)
		5	=Transparent XON (&K5)
		6	=Both methods (&K6)
		Bits 3-7Reserved
	S40	Accepted but ignored.		-	-	*	104
	S40	Accepted but ignored.		-	-	*	(68h)
							(68h)
	S41	Accepted but ignored.		-	-	*	195
	S41	Accepted but ignored.		-	-	*	(C3h)
							(C3h)
	S42 - S45	Reserved		-	-		-
	S46	Accepted but ignored.		-	-	*	138
	S48	Accepted but ignored.		-	-	*	7
	S82	Accepted but ignored.		-	-		128(40h)
	S86	Accepted but ignored.		0-255	-		-

46	Chapter 9 Modem Emulation

Image 46

Digi W manual =XON/XOFF &K4

Contents

Digi TS W Family 9000329B N t e n t s Chapter Configuring WirelessConfiguring the IP Address Chapter Introduction Chapter Configuring PPP Setting Up RealPortConfiguring the Serial Ports Chapter Configuring Autoconnection Configuring IP Routing Configuring Security Features Configuring Snmp Configuring the Digi Device for IAIndustrial AutomationConfiguring DNS Configuring Users Configuring Power Over the Serial Ports Reference and Certifications Contents Setup Overview T r o d u c t i o n About This Guide About Entering Commands on the Command LineSupported Devices Other Documents in the Library About Configuration Methods Configuration Prerequisites Configuration Considerations N f i g u r i n g W i r e l e s s Select Discover Digi Device from the CD Configuring Wireless Configuring Wireless Configuring Wireless Configuring Wireless Options for Configuring the IP Address and Mask N f i g u r i n g t h e I P a d d r e s s Configuring the IP Address Using ARP-Ping Configuring the Ethernet Interface from the Command Line Configuring an IP Address using Dhcp and Rarp T t i n g U p R e a l P o r t About RealPort Setting Up RealPort Options for Configuring the Serial Ports Configuring the Serial Port Settings with the Web Interface Configuring the Serial Port Settings from the Command Line Configuring Inbound PPP Connections N f i g u r i n g P P P Configuring Inbound PPP Connections Example Configuring Outbound PPP Connections Command Line Procedure Sample Use the following table for additional configurations Configuring PPP Modem Emulation Digi One TS and PortServer TS 2/4 MEI only D e m E m u l a t i o nCommon User Scenarios Modem Emulation Cable Signals Serial Device Digi Device Server Originating, Answering, and Disconnecting Calls Application AT Com Digi Device Server Response Mand Server. P represents a one second pause Modem Emulation AT Command Set Function Result Code Function Result ATP ATXn Accepted but ignored There is no Nvram support currently AT+MS Registers Function Range Units Saved Default Ascii Register Function Range Units Saved Default Register Function Range Units Saved Default 17 11h =XON/XOFF &K4 Result Codes Short Long Form Modem Emulation Configuring a User for Autoconnection Web Interface Configuring a Port for Autoconnection Web InterfaceCommands for Configuring Autoconnection by Port or by User N f i g u r i n g a u t o c o n n e c t i o n Click Serial Ports Configuring TCP Socket CommunicationConfiguring UDP Multicast Click Change Profile Click Change Profile and select UDP Socket Configuring Autoconnection Configuring Static Routes N f i g u r i n g I P R o u t i n g Configuring Dynamic Routes Using RIP Configuring Proxy ARP Configuring IP Routing Controlling Access to Inbound Ports Controlling Access to the ConfigurationN f i g u r i n g S e c u r i t y F e a t u r e s Controlling Access to Outbound Ports Controlling Access to the Command Line Configuring SSH Version 2 for Secure Communication Issuing User PasswordsDevice Required Hardware Firmware Controlling Access to Services Http Snmp SSH Configuring Security Features Configuring Modbus Configuring the User-Defined Protocol Configuring the Digi Device for IA Industrial Automation N f i g u r i n g D N S About the Domain Name System Configuration Procedures N f i g u r i n g S N M P About Snmp and the Device Server Agent Configuration Procedure Web Interface MIB Feature Description Set user Field About Configuring UsersCommon User Features N f i g u r i n g U s e r s Commands for Configuring a User Configuring a User Web InterfaceClick New User Copying the Configuration to and from a Remote Host Upgrading the Firmware Resetting Device Server Configuration to Defaults Commands for Resetting the Configuration to Defaults Managing the OS and Configuration Serial Power Feature Configuring RI Power Configuring DTR Power Serial Power Table DTR on DTR OFF Configuring Power Over the Serial Ports Interpreting the LEDs F e r e n c e a n d C e r t i f i c a t i o n sColor State Indicates RJ-45 Pinouts EIA-232 EIA-422/485 EIA-485 Half Full-Duplex Certifications Environmental Digi Contact Information Digi Contacts Reference and Certifications