N f i g u r i n g t h e I P a d d r e s s | Digi W guide

Chapter 5	C o n f i g u r i n g t h e I P A d d r e s s

Options for Configuring the IP Address and Mask

The device server IP address can be configured using the following methods:

•With Digi Port Authority-Remote, a Digi utility on the Software and Documentation CD.

•By updating the ARP table on a server and then pinging the Digi device (called ARP-Ping, see "Configuring the IP Address Using ARP-Ping" on page 20).

•From the command line using the set config command ("Configuring the Ethernet Interface from the Command Line" on page 21.)

•Using a RARP server ("Configuring an IP Address using DHCP and RARP" on page 22.)

•Using a DHCP server ("Configuring an IP Address using DHCP and RARP" on page 22.)

The IP address and mask can also be changed using the web interface. This method, however, does not work for the initial IP address configuration.

Device Support: Digi Port Authority-Remote and ARP-Ping for IP Address

Configuration

Not all Digi devices can use Digi Port Authority-Remote and ARP-Ping for IP address configuration. To determine if you can use these features, find the hardware label on your Digi device and then use the table below to determine whether this feature is available:

Device	Part Number	Revision Required
Digi One IA RealPort	50000764-01	F or higher

Digi One RealPort	50000723-01	J or higher

PortServer TS 2	50000723-02	J or higher

PortServer TS 4	50000723-03	G or higher

Configuring the Ethernet Interface with Digi Port Authority-Remote

Use this section to configure an initial IP address, subnet mask, and default gateway using Digi Port Authority-Remote. This procedure cannot be used to change the IP address, but only to assign the initial IP address. It also cannot be used if a DHCP server is active.

Starting Point

This procedure assumes the following:

•That your Digi device supports this feature. See "Device Support: Digi Port Authority-Remote and ARP-Ping for IP Address Configura- tion" on page 19.

•That your Digi device is connected to the Ethernet network.

Chapter 5 Configuring the IP Address

19

Image 19

Digi W manual N f i g u r i n g t h e I P a d d r e s s, Options for Configuring the IP Address and Mask

Contents

Digi TS W Family 9000329B Chapter Introduction Chapter Configuring WirelessConfiguring the IP Address N t e n t s Chapter Configuring Autoconnection Setting Up RealPortConfiguring the Serial Ports Chapter Configuring PPP Configuring Security Features Configuring IP Routing Configuring Users Configuring the Digi Device for IAIndustrial AutomationConfiguring DNS Configuring Snmp Reference and Certifications Configuring Power Over the Serial Ports Contents T r o d u c t i o n Setup Overview Other Documents in the Library About Entering Commands on the Command LineSupported Devices About This Guide About Configuration Methods Configuration Prerequisites N f i g u r i n g W i r e l e s s Configuration Considerations Select Discover Digi Device from the CD Configuring Wireless Configuring Wireless Configuring Wireless Configuring Wireless N f i g u r i n g t h e I P a d d r e s s Options for Configuring the IP Address and Mask Configuring the IP Address Using ARP-Ping Configuring the Ethernet Interface from the Command Line Configuring an IP Address using Dhcp and Rarp About RealPort T t i n g U p R e a l P o r t Setting Up RealPort Configuring the Serial Port Settings with the Web Interface Options for Configuring the Serial Ports Configuring the Serial Port Settings from the Command Line N f i g u r i n g P P P Configuring Inbound PPP Connections Configuring Outbound PPP Connections Command Line Configuring Inbound PPP Connections Example Procedure Sample Use the following table for additional configurations Configuring PPP Modem Emulation Digi One TS and PortServer TS 2/4 MEI only D e m E m u l a t i o nCommon User Scenarios Serial Device Digi Device Server Modem Emulation Cable Signals Application AT Com Digi Device Server Response Mand Originating, Answering, and Disconnecting Calls Server. P represents a one second pause Code Modem Emulation AT Command Set Function Result ATP Function Result ATXn Accepted but ignored There is no Nvram support currently AT+MS Ascii Registers Function Range Units Saved Default Register Function Range Units Saved Default Register Function Range Units Saved Default 17 11h =XON/XOFF &K4 Result Codes Short Long Form Modem Emulation N f i g u r i n g a u t o c o n n e c t i o n Configuring a Port for Autoconnection Web InterfaceCommands for Configuring Autoconnection by Port or by User Configuring a User for Autoconnection Web Interface Click Change Profile Configuring TCP Socket CommunicationConfiguring UDP Multicast Click Serial Ports Click Change Profile and select UDP Socket Configuring Autoconnection N f i g u r i n g I P R o u t i n g Configuring Static Routes Configuring Dynamic Routes Using RIP Configuring Proxy ARP Configuring IP Routing Controlling Access to Inbound Ports Controlling Access to the ConfigurationN f i g u r i n g S e c u r i t y F e a t u r e s Controlling Access to the Command Line Controlling Access to Outbound Ports Configuring SSH Version 2 for Secure Communication Issuing User PasswordsDevice Required Hardware Firmware Http Controlling Access to Services Snmp SSH Configuring Security Features Configuring the User-Defined Protocol Configuring Modbus Configuring the Digi Device for IA Industrial Automation About the Domain Name System N f i g u r i n g D N S Configuration Procedures About Snmp and the Device Server Agent N f i g u r i n g S N M P MIB Configuration Procedure Web Interface N f i g u r i n g U s e r s About Configuring UsersCommon User Features Feature Description Set user Field Commands for Configuring a User Configuring a User Web InterfaceClick New User Upgrading the Firmware Copying the Configuration to and from a Remote Host Resetting Device Server Configuration to Defaults Commands for Resetting the Configuration to Defaults Managing the OS and Configuration Configuring RI Power Serial Power Feature Configuring DTR Power DTR on DTR OFF Serial Power Table Configuring Power Over the Serial Ports Interpreting the LEDs F e r e n c e a n d C e r t i f i c a t i o n sColor State Indicates RJ-45 Pinouts EIA-232 EIA-422/485 EIA-485 Half Full-Duplex Environmental Certifications Digi Contact Information Digi Contacts Reference and Certifications