T t i n g U p R e a l P o r t, About RealPort | Digi W specs

Chapter 6

About RealPort

S e t t i n g U p R e a l P o r t

This section provides a brief introduction to RealPort.

What is RealPort?

RealPort is a feature that allows network-based host systems to use the ports of the device server as though they were the host system’s own ports, appearing and behaving as local ports to the network-based host.

RealPort Advantages

RealPort provides the following advantages:

•It expands the number of ports available to the host system.

•It enables device server ports to be treated as if they were directly connected to the host, which means they use all standard operating system interfaces that control baud rate, parity, stop bits, and flow control.

•It enables host administrators to do most of the required configuration on the host, the system with which the administrator is most familiar.

•It dramatically reduces host CPU overhead because multiple terminal or printer sessions are multiplexed over the same TCP/IP connection.

Configuring the RealPort Software

You must install and configure RealPort software on each host that will use RealPort ports. See the RealPort documentation for more information.

1.From the CD, click Software. (If the wizard pops up, click cancel.) The files are located in the drivers\windows\win2k\realport folder.

If you use the wizard, follow the steps in the pop-up after selecting the Incoming scenario.

Chapter 6 Setting Up RealPort

23

Image 23

Digi W manual T t i n g U p R e a l P o r t, About RealPort

Contents

Digi TS W Family 9000329B Chapter Introduction Chapter Configuring WirelessConfiguring the IP Address N t e n t s Chapter Configuring Autoconnection Setting Up RealPortConfiguring the Serial Ports Chapter Configuring PPP Configuring Security Features Configuring IP Routing Configuring Users Configuring the Digi Device for IAIndustrial AutomationConfiguring DNS Configuring Snmp Reference and Certifications Configuring Power Over the Serial Ports Contents T r o d u c t i o n Setup Overview Other Documents in the Library About Entering Commands on the Command LineSupported Devices About This Guide About Configuration Methods Configuration Prerequisites N f i g u r i n g W i r e l e s s Configuration Considerations Select Discover Digi Device from the CD Configuring Wireless Configuring Wireless Configuring Wireless Configuring Wireless N f i g u r i n g t h e I P a d d r e s s Options for Configuring the IP Address and Mask Configuring the IP Address Using ARP-Ping Configuring the Ethernet Interface from the Command Line Configuring an IP Address using Dhcp and Rarp About RealPort T t i n g U p R e a l P o r t Setting Up RealPort Configuring the Serial Port Settings with the Web Interface Options for Configuring the Serial Ports Configuring the Serial Port Settings from the Command Line N f i g u r i n g P P P Configuring Inbound PPP Connections Configuring Outbound PPP Connections Command Line Configuring Inbound PPP Connections Example Procedure Sample Use the following table for additional configurations Configuring PPP Common User Scenarios D e m E m u l a t i o nModem Emulation Digi One TS and PortServer TS 2/4 MEI only Serial Device Digi Device Server Modem Emulation Cable Signals Application AT Com Digi Device Server Response Mand Originating, Answering, and Disconnecting Calls Server. P represents a one second pause Code Modem Emulation AT Command Set Function Result ATP Function Result ATXn Accepted but ignored There is no Nvram support currently AT+MS Ascii Registers Function Range Units Saved Default Register Function Range Units Saved Default Register Function Range Units Saved Default 17 11h =XON/XOFF &K4 Result Codes Short Long Form Modem Emulation N f i g u r i n g a u t o c o n n e c t i o n Configuring a Port for Autoconnection Web InterfaceCommands for Configuring Autoconnection by Port or by User Configuring a User for Autoconnection Web Interface Click Change Profile Configuring TCP Socket CommunicationConfiguring UDP Multicast Click Serial Ports Click Change Profile and select UDP Socket Configuring Autoconnection N f i g u r i n g I P R o u t i n g Configuring Static Routes Configuring Dynamic Routes Using RIP Configuring Proxy ARP Configuring IP Routing N f i g u r i n g S e c u r i t y F e a t u r e s Controlling Access to the ConfigurationControlling Access to Inbound Ports Controlling Access to the Command Line Controlling Access to Outbound Ports Device Required Hardware Firmware Issuing User PasswordsConfiguring SSH Version 2 for Secure Communication Http Controlling Access to Services Snmp SSH Configuring Security Features Configuring the User-Defined Protocol Configuring Modbus Configuring the Digi Device for IA Industrial Automation About the Domain Name System N f i g u r i n g D N S Configuration Procedures About Snmp and the Device Server Agent N f i g u r i n g S N M P MIB Configuration Procedure Web Interface N f i g u r i n g U s e r s About Configuring UsersCommon User Features Feature Description Set user Field Click New User Configuring a User Web InterfaceCommands for Configuring a User Upgrading the Firmware Copying the Configuration to and from a Remote Host Resetting Device Server Configuration to Defaults Commands for Resetting the Configuration to Defaults Managing the OS and Configuration Configuring RI Power Serial Power Feature Configuring DTR Power DTR on DTR OFF Serial Power Table Configuring Power Over the Serial Ports Color State Indicates F e r e n c e a n d C e r t i f i c a t i o n sInterpreting the LEDs RJ-45 Pinouts EIA-232 EIA-422/485 EIA-485 Half Full-Duplex Environmental Certifications Digi Contact Information Digi Contacts Reference and Certifications