Mib, Configuration Procedure Web Interface | Digi specs

•Read-write for the character-stream devices using SMIv2 MIB (RFC 1658)

•Read-write for the RS-232-like hardware devices MIB (RFC 1659)

•Read-write for the device server IP Network Control Protocol of the Point-to-Point Protocol MIB (RFC 1473)

Message Support

The SNMP agent supports the Set, Get, GetNext, and Trap messages as defined in RFC 1157. These messages are used as follows:

•Set, which means set the value of a specific object from one of the supported MIBs

•Get, which means retrieve the value of a specific object form one of the supported MIBs

•GetNext, which means retrieve the value of the next object in the

MIB

•Trap, which means send traps to the manager when a particular type of significant event occurs

Supported Traps

The agent can send traps when any of the following occur:

•Cold starts (device server initializes)

•Authentication failures

•Login attempts

Configuration Procedure: Web Interface

1.Access the web interface by entering the device server IP address in a browser’s URL window.

2.Log on to the device server as root.

Note: The default password is dbps, which should be changed. See the newpass command in the Digi One/PortServer TS Command Reference for information on changing passwords.

3.Click SNMP under System from the menu.

4.Fill in the configuration fields and click Apply to save settings.

68	Chapter 15 Configuring SNMP

Image 68

Digi manual Mib, Configuration Procedure Web Interface

Contents

Digi TS W Family 9000329B Chapter Configuring Wireless Configuring the IP AddressN t e n t s Chapter Introduction Setting Up RealPort Configuring the Serial PortsChapter Configuring PPP Chapter Configuring Autoconnection Configuring IP Routing Configuring Security Features Configuring the Digi Device for IAIndustrial Automation Configuring DNSConfiguring Snmp Configuring Users Configuring Power Over the Serial Ports Reference and Certifications Contents Setup Overview T r o d u c t i o n About Entering Commands on the Command Line Supported DevicesAbout This Guide Other Documents in the Library About Configuration Methods Configuration Prerequisites Configuration Considerations N f i g u r i n g W i r e l e s s Select Discover Digi Device from the CD Configuring Wireless Configuring Wireless Configuring Wireless Configuring Wireless Options for Configuring the IP Address and Mask N f i g u r i n g t h e I P a d d r e s s Configuring the IP Address Using ARP-Ping Configuring the Ethernet Interface from the Command Line Configuring an IP Address using Dhcp and Rarp T t i n g U p R e a l P o r t About RealPort Setting Up RealPort Options for Configuring the Serial Ports Configuring the Serial Port Settings with the Web Interface Configuring the Serial Port Settings from the Command Line Configuring Inbound PPP Connections N f i g u r i n g P P P Configuring Inbound PPP Connections Example Configuring Outbound PPP Connections Command Line Procedure Sample Use the following table for additional configurations Configuring PPP Common User Scenarios D e m E m u l a t i o nModem Emulation Digi One TS and PortServer TS 2/4 MEI only Modem Emulation Cable Signals Serial Device Digi Device Server Originating, Answering, and Disconnecting Calls Application AT Com Digi Device Server Response Mand Server. P represents a one second pause Modem Emulation AT Command Set Function Result Code Function Result ATP ATXn Accepted but ignored There is no Nvram support currently AT+MS Registers Function Range Units Saved Default Ascii Register Function Range Units Saved Default Register Function Range Units Saved Default 17 11h =XON/XOFF &K4 Result Codes Short Long Form Modem Emulation Configuring a Port for Autoconnection Web Interface Commands for Configuring Autoconnection by Port or by UserConfiguring a User for Autoconnection Web Interface N f i g u r i n g a u t o c o n n e c t i o n Configuring TCP Socket Communication Configuring UDP MulticastClick Serial Ports Click Change Profile Click Change Profile and select UDP Socket Configuring Autoconnection Configuring Static Routes N f i g u r i n g I P R o u t i n g Configuring Dynamic Routes Using RIP Configuring Proxy ARP Configuring IP Routing N f i g u r i n g S e c u r i t y F e a t u r e s Controlling Access to the ConfigurationControlling Access to Inbound Ports Controlling Access to Outbound Ports Controlling Access to the Command Line Device Required Hardware Firmware Issuing User PasswordsConfiguring SSH Version 2 for Secure Communication Controlling Access to Services Http Snmp SSH Configuring Security Features Configuring Modbus Configuring the User-Defined Protocol Configuring the Digi Device for IA Industrial Automation N f i g u r i n g D N S About the Domain Name System Configuration Procedures N f i g u r i n g S N M P About Snmp and the Device Server Agent Configuration Procedure Web Interface MIB About Configuring Users Common User FeaturesFeature Description Set user Field N f i g u r i n g U s e r s Click New User Configuring a User Web InterfaceCommands for Configuring a User Copying the Configuration to and from a Remote Host Upgrading the Firmware Resetting Device Server Configuration to Defaults Commands for Resetting the Configuration to Defaults Managing the OS and Configuration Serial Power Feature Configuring RI Power Configuring DTR Power Serial Power Table DTR on DTR OFF Configuring Power Over the Serial Ports Color State Indicates F e r e n c e a n d C e r t i f i c a t i o n sInterpreting the LEDs RJ-45 Pinouts EIA-232 EIA-422/485 EIA-485 Half Full-Duplex Certifications Environmental Digi Contact Information Digi Contacts Reference and Certifications