Diagnostic Messages, Error | Emerson 3051N instruction

Reference Manual

00809-0100-4808, Rev CA June 2008

Rosemount 3051N

FIGURE 6-2. Rosemount 3051N with Optional LCD Meter.

Diagnostic Messages

In addition to the output, the LCD meter displays abbreviated operation, error, and warning messages for troubleshooting the transmitter. Messages appear according to their priority, with normal operating messages appearing last. To determine the cause of a message, use a HART Communicator to further interrogate the transmitter. A description of each LCD diagnostic message follows.

Error	Error messages appear on the LCD meter display to inform you of serious
	problems effecting the operation of the transmitter. The meter displays an
	error message until the error condition is corrected, and the analog output is
	driven to the specified alarm level. No other transmitter information is
	displayed during an alarm condition.
	FAIL
	The transmitter CPU board and the sensor module are incompatible. If you
	encounter this message, contact Rosemount Nuclear Instruments, Inc. at
	(952) 949-5210 if you need assistance.
	FAIL MODULE
	The sensor module is disconnected or is malfunctioning. Verify that the
	sensor module ribbon cable is connected to the back of the electronics board.
	If the ribbon cable is properly connected, there is a problem within the sensor
	module. Possible sources of problems include:
	• Pressure or temperature updates are not being received in the sensor
	module.
	• A non-volatile memory fault that will effect transmitter
	operation has been detected in the module by the memory verification
	routine.

6-5

Image 71

Emerson 3051N manual Diagnostic Messages, Error

Contents

Reference Manual Important Notice -- Errata Rosemount 3051N Return of Material Changes Changes from June 2006 to JuneOld Rosemount 3051N Table of Contents Specifications Reference Data InstallationTroubleshooting Hart Communicator OptionsAppendix a Glossary Index Section Introduction Using this Manual Rosemount 3051N Transmitter Functions Overview Safety Messages Security Alarm Level VerificationTransmitter Physical Removal Local Zero and Span Local Keys Configuring Transmitter Alarm and Security Jumper Procedure Electronics Board Setting the Loop to Manual Wiring Diagrams Bench Hook-up Wiring Diagrams Field Hook-up Process Variables Review Configuration DataCheck Output Set Output Sensor TemperatureBasic Setup Set Process Variable Units Rerange with a Communicator Only Rerange Rerange with a Pressure Input Source and a Communicator Span and Zero Adjustment Buttons Diagnostics Service Detailed Setup Calibration Transmitter TestLoop Test Transmitter Bench Calibration Tasks Field Calibration Tasks Calibration Overview Configure the Analog Output Parameters URV Sensor Trim Typical Zero vs Non-zero-Based Application Illustrations Zero Trim Digital Trim Connection Drawing 4-20 mA Transmitters Full Trim Analog Output Trim Digital-to-Analog Trim Using Other ScaleRecall Factory Trim Recall Factory Trim- Sensor Trim Recall Factory Trim- Analog Output Zero Effect HTc = URV + S URV Ps Rosemount 3051N Section Installation Rosemount 3051N Typical Installation Flowchart Mechanical Considerations General ConsiderationsSpecial Draft Range Considerations 156 181 16 x 11/4 Bolts for Mounting to 54.1 Transmitter 120 127 66.8 Traditional Flange Option Code H2 Dimensional Drawing Mounting Rosemount 3051N GAS or Liquid Service GAS Service Steam Service Electrical Considerations Process Connections Housing RotationPower Supply Power Supply Load Limitations Wiring Environmental Considerations Access Requirements Cover InstallationGrounding the Transmitter Case Troubleshooting Returning Rosemount Products and Materials Symptom Corrective Actions Seismic Nuclear Specifications Model Range Code Hydrostatic Test Pressure Drift Performance SpecificationsAmbient Temperature Effect12 Reference Accuracy Range Code Static Pressure Zero Effect1 Power Supply Effect Load Effect Mounting Position EffectOverpressure Effect Static Pressure Effect Range Code Overpressure Effect Output Functional SpecificationsService Temperature Limits Range Code Minimum Time Constant Tc Including Dead Time Td Span and Zero, Zero Elevation, SuppressionRange Minimum Span Upper URL Lower LRL Overpressure Limits Burst Pressure Maximum WorkingPressure12 Static Pressure Limits Physical Specifications Materials of Construction Option Code Description Add Ordering Information Meters optional Configuration InformationHousing Material Conduit Entry Size Mounting Bracket Options Date On Rosemount 3051N Exploded View with Coplanar Process Flange Rosemount 3051N Rosemount 3051N Section Options Overview Safety Messages LCD Meter Custom Meter Configuration Exploded View of the Rosemount 3051N with Optional LCD Meter Installing the Meter Rosemount 3051N Error Diagnostic Messages Press Limit Mounting Brackets Operation Transient Protection Terminal Block T1 Traditional Flange H2 Transient Protection Terminal Block T1 Rosemount 3051N Appendix a Hart Communicator Introduction Safety Messages Rosemount 3051N Online Menu Function Hart Fast Key Sequence Connections and Hardware Figure A-3. Rosemount Hart terminal access door Figure A-4. Bench Hook-up MA Transmitters Action Keys RosemountCommunicator Keys Data Entry Function KeysAlphanumeric and Shift Keys Main Menu Fast Key SequencesFast Key Sequence Conventions Fast Key Sequence Example Menus Functions Online Menu Touch Multifunction LED Processing Indication Alphanumeric KeysMultifunction LED Touch Screen Rosemount 3051N Message Description Diagnostic MessagesFast Key Sequences Hot Key options Rosemount 3051N Uploadvariable Rosemount 3051N Rosemount 3051N Glossary Smart Family Index 00809-0100-4808, Rev CA June Security Page ¢00809-0100-4801V¤