Installation | Enterasys Networks 7G4285-49, 7G4205-72 specs

3

Installation

Electrical Hazard: Only qualified personnel should perform installation procedures.

Riesgo Electrico: Solamente personal calificado debe realizar procedimientos de instalacion.

Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden.

Important Notice

Read the Release Notes shipped with the DFE modules to check for any exceptions to the supported features and operation documented in this guide.

This chapter provides the instructions to install the 7G4285‐49 and 7G4205‐72 DFE modules. Follow the order of the sections listed below to correctly install the DFE modules.

For information about...	Refer to page...

Installation Site Requirement	3-2

Required Tools	3-2

Unpacking the DFE Module	3-2

Installing an Optional Network Expansion Module (NEM)	3-3

DFE Module Placement and Installation Rules	3-3

Preparing to Install into a Chassis	3-6

Connecting 48 Vdc Power for PoE Operation	3-12

Connecting to the Network	3-12

Connecting to COM Port for Local Management	3-18

Completing the Installation	3-24

DFE-Platinum Series Hardware Installation Guide 3-1

Image 33

Enterasys Networks 7G4285-49, 7G4205-72 manual Installation

Contents

Enterasys Matrix Page Page Federal Communications Commission FCC Notice Product SafetyIndustry Canada Notice Class a ITE Notice Clase A. Aviso de ITE Compatibilidad Electromágnetica EMC Electromagnetic Compatibility EMCElektro- magnetische Kompatibilität EMC Hazardous Substances Supplement to Product Instructions Bsmi EMC Statement Taiwan Vcci Notice Declaration of Conformity Safety Information Class 1 Laser Transceivers Enterasys NETWORKS, INC. Firmware License Agreement Viii Page Page Contents Appendix a Specifications Figures Xiv Who Should Use This Guide About This Guide How to Use This Guide Related DocumentsFor Refer to Following conventions are used in this guide Conventions Used in This Guide Support@enterasys.com Getting Help Overview of DFE-Platinum Series Module Capabilities Introduction 7G4285-49 DFE Module and Interface Options 7G4285-49 DFE-Platinum Module 7G4205-72 7G4205-72 DFE-Platinum Module Network Expansion Module NEM Switch Configuration Using WebViewConnectivity Management Switch Configuration Using CLI Commands Secure Networks Policy SupportStandards Compatibility Lanview Diagnostic LEDs Network Requirements 10BASE-T Network Link Aggregation 1000BASE-T Network 100BASE-TX Network 1000BASE-T Network Network Requirements Installation Contents of DFE Module Carton Quantity Installation Site RequirementRequired Tools Unpacking the DFE Module Installing an Optional Network Expansion Module NEM DFE Module Placement and Installation RulesMatrix E7 Chassis Module Placement Example 1 -1,A Example 2 -1,BExample 3 -1, C Example 4 -1,D Example 5 -1, EExample 6 -1, F Preparing to Install into a Chassis Installing the DFE Modules into a Matrix E7 or N7 Chassis Preparing to Install into a Chassis Preparing to Install into a Chassis Installing the DFE Modules into a Matrix N3 or N5 Chassis Card guides Connecting to the Network Connecting 48 Vdc Power for PoE Operation Making the UTP Connections Connecting UTP Cables to DFE Modules Connecting a Twisted Pair Segment with RJ45 Connector RX+ TX+ TX1+ 1 RX1- 2 TX2+ 3 TX3+ 4 RX3- 5 RX2- 6 TX4+ 7 RX4 Verifying PoE Port Status Connecting to COM Port for Local Management What Is NeededConnecting to an IBM PC or Compatible Device Parameter Setting Connecting to a VT Series Terminal 10 Connecting a VT Series Terminal Connecting to a Modem 11 Connecting to a Modem Adapter Wiring and Signal Assignments COM Port Adapter Wiring and Signal Diagram RJ45RJ45 DB25 Modem Port Adapter Wiring and Signal Diagram Completing the Installation Completing the Installation of a New SystemFirst-Time Log-In Using a Console Port Connection 12 Matrix DFE Startup Screen Example N7 Chassis Enter Logging in with an Administratively-Configured User Account Troubleshooting Using LanviewAbout the Management Mgmt LED Lanview LEDs on 7G4285-49 Viewing Receive/Transmit Activity on 7G4285-49 Lanview LEDs on 7G4205-72 Viewing Receive/Transmit Activity on 7G4205-72 Viewing the PoE Port Status Color State Recommended Action Lanview LEDs LED RX/TX Platinum Series Configuration Guide for Troubleshooting Checklist Problem Possible Cause Recommended Action Troubleshooting Checklist Overview of DFE Module Shutdown Procedure OFFLINE/RESET Switch Recommended Shutdown Procedure Using OFFLINE/RESET Switch Last Resort Shutdown Procedure Using OFFLINE/RESET Switch Specifications Table A-1 7G4285-49 Specifications DFE Module SpecificationsProcessors/Memory Physical Table A-2 7G4205-72 Specifications COM Port Pinout Assignments Table A-3 COM Port Pin Assignments Signal Name Input/OutputRegulatory Compliance Table A-4 Compliance Standards Regulatory Compliance Mode Switch Settings and Option Installations Setting the Mode Switches Memory Locations and Replacement Procedures Dram Simm Dimm Removing the Safety Cover Gaining Access to Memory Modules Figure B-3 Removing the Safety Cover Figure B-4 Removing the Optional Network Expansion Module Dram Simm Replacement Procedure Gaining Access to Memory Modules Removing the Dimm Figure B-6 Installing the Dimm Dimm Replacement Procedure Figure B-7 Removing the Existing Dimm Figure B-8 Installing the Dimm Installing the Network Expansion Module NEM Figure B-9 Installing the Network Expansion Module NEM Reinstalling the Safety Cover Figure B-10 Installing the Safety Cover Page Overview About PoE Power over Ethernet Proprietary PD Detection Table C-2 PoE Status LED Indications PoE Port Status PoE Port Status LEDs Overview About PoE Power over Ethernet Numerics Index NEM B-12 installing