Manuals / Enterasys Networks / Photography / Camera Accessories

Enterasys Networks X009-U manual 2 Disassembly Steps 3 and, 3 Disassembly Steps 5 through

Models: X009-U

1 86

Download 86 pages 56.4 Kb

Page 33

Figure 3-2 Disassembly Steps 3 and 4

Unpacking the Matrix X4-C Chassis

Figure 3-2 Disassembly Steps 3 and 4

2

3

1

6

5

4

1	Accessory package	3	Documentation	5	Styrofoam cap
2	Screw packet	4	RJ45 management cable	6	Rack support brackets (2)

5.Open the top of the shipping bag covering the unit, then pull the bag down around the skid, as shown in Figure 3‐3.

Figure 3-3 Disassembly Steps 5 through 8

34

1

4

3

2

1 Chassis

2 Shipping bag and skid

3 Shipping screws (10)

4 Shipping brackets (4)

Matrix X4-C Chassis Installation Guide 3-3

Image 33

Enterasys Networks X009-U manual 2 Disassembly Steps 3 and, 3 Disassembly Steps 5 through

Contents

X4-C Chassis Installation Guide Enterasys MatrixSecure Core Router Page Enterasys Networks, Inc 50 Minuteman Road Andover, MA Regulatory Compliance Information Product SafetyFederal Communications Commission FCC Notice Industry Canada NoticeCompatibilidad Electromágnetica EMC Electromagnetic Compatibility EMCElektro-magnetische Kompatibilität EMC Hazardous SubstancesSupplement to Product Instructions VCCI Notice Safety Information Class 1 Laser TransceiversBSMI EMC Statement - Taiwan The single mode interface modules use Class 1 laser transceiversDeclaration of Conformity Enterasys Networks, Inc Firmware License Agreement BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCTCAREFULLY READ THIS LICENSE AGREEMENT 4. EXPORT RESTRICTIONS. You understand that Enterasys and its Affiliates are subject to regulation by agencies of the U.S. Government, including the U.S. Department of Commerce, which prohibit export or diversion of certain technical products to certain countries, unless a license to export the Program is obtained from the U.S. Government or an exception from obtaining such license may be relied upon by the exporting party 10. ENFORCEMENT. You acknowledge and agree that any breach of Sections 2, 4, or 9 of this Agreement by You may cause Enterasys irreparable damage for which recovery of money damages would be inadequate, and that Enterasys may be entitled to seek timely injunctive relief to protect Enterasys’ rights under this Agreement in addition to any and all remedies available at law Page Chapter 2 Site and Configuration Guidelines ContentsChapter 3 Matrix X4-C Chassis Setup About This GuideIndex Appendix A Specifications and Regulatory ComplianceFigures Tables About This Guide Using This GuideWho Should Use This Guide For information aboutConventions Used in This Guide Using the Matrix X Router Manual SetMatrix X Router Configuration Guide Matrix X Router Command Line Interface Reference GuideGetting Help Commonly Used Acronymsxviii About This Guide Getting HelpSystem Description OverviewFigure 1-2 Matrix X4-C Chassis as Shipped Rear View Figure 1-1 Matrix X4-C Chassis with Redundant Power SuppliesFeatures X4-C Input/Output ModulesX4-C Control Module Installing Redundant CMs into an Active Matrix X Router 5. Insert the standby CM into the system and wait until it is fully synchronized with the active CM before removing the active CM. Do not physically remove the active CM during the synchronization process. The following message will appear on your console screen X4-C Fabric Module Proper CM RecoveryPower Supply LEDs X4-C Redundant Power SuppliesAuto-Ranging Power Supplies Power Supply ReplacementRack-Mountable Chassis Site Guidelines Site and Configuration GuidelinesConfiguration Guidelines Configuration Guidelines2-2 Site and Configuration Guidelines Required Tools Matrix X4-C Chassis SetupUnpacking the Matrix X4-C Chassis Figure 3-1 Disassembly Steps 1 andFigure 3-3 Disassembly Steps 5 through Figure 3-2 Disassembly Steps 3 and7. Lift and remove the chassis from the skid Setting Up the Matrix X4-C Chassis Setup OrderInstalling the Matrix X4-C Chassis Figure 3-4 Installing Rack Support Brackets Installing Optional Rack Support BracketsFigure 3-5 Fastening Mid-Mount Brackets Installing Optional Mid-Mount BracketsFigure 3-6 Rack Mounting the Matrix X4-C Chassis Rack Mounting the Matrix X4-C ChassisFigure 3-7 Rack Mounting the Mid-Mounted Chassis Chassis Bonding and GroundingFigure 3-8 Telcordia GR-1089 Grounding Hole Pattern and Cable Installing and Removing a Power Supply Attaching the Electrostatic Discharge Wrist StrapFigure 3-9 ESD Grounding Receptacle Installing a Power Supply Power Supply PlanningFigure 3-10 Power Supply Planning N + 1 Method Figure 3-11 Power Supply Planning 1 + 1 MethodFigure 3-12 Removing Power Supply Vent Plate Figure 3-14 Removing Coverplate from Power Supply Slot Figure 3-13 Installing Power Supply ModuleFigure 3-15 Removing the AC Inlet Power Cord Removing a Power SupplyInstalling and Removing a Fan Tray Installing a Fan TrayFigure 3-16 Removing Fan Tray Bezel Removing a Fan Tray Figure 3-17 Installing Fan TrayInstalling and Removing IOMs Installing and Removing ModulesFigure 3-18 Installing IOMs Figure 3-19 Engaging Ejector HandlesInstalling and Removing Modules Figure 3-20 Removing IOM Coverplate3-20 Matrix X4-C Chassis Setup MatrixFigure 3-21 Installing Control Module Installing and Removing CMsAll Rights Reserved E7501 & Banias Rev #1.03 PhoenixBIOS 2002 Q3 Replacing the CM Battery1024K Cache SRAM Passed System BIOS shadowed Fixed Disk 0 SAMSUNG CF/ATA ERROR 0271 Check date and time settingsFigure 3-22 Installing Fabric Module Installing and Removing FMsInstalling an XFP/SFP Module Attaching Cables, Installing Compact Flash Card and DIMM Upgrade KitConnecting Fiber-Optic Cables Figure 3-23 Installing XFP/SFP Optical TransceiverRemoving an XFP/SFP Module MT-RJ Figure 3-24 Attaching LC or MT-RJ Cable ConnectorConnecting the CM COM Port to an IBM PC or Compatible Device Connecting to the CM COM PortFigure 3-25 Connecting an IBM PC or Compatible Connecting the CM COM Port to a VT Series TerminalFigure 3-26 Connecting a VT Series Terminal Connecting the CM COM Port to a ModemFigure 3-27 Connecting to a Modem Adapter Wiring and Signal AssignmentsConnecting to the CM USB Port Installing a Compact Flash Card Figure 3-29 Installing Flash CardFigure 3-28 Attaching a USB Device to the CM Installing the Memory Upgrade Kit Removing the DIMMsFigure 3-30 Locating the DIMMs on the CM Figure 3-31 Removing the Existing DIMM Installing the DIMMsOptional Cable Management Kit Installing the Cable Management AssemblyFigure 3-33 Securing Cables Using the Velcro Cable Straps Figure 3-32 Installing the Cable Management AssemblyPowering Up the Matrix X4-C Chassis LEDs and Reset ButtonFigure 3-34 Connecting 20 Amp AC Power Cord to the Power Supply Power Supply LEDs Figure 3-35 Power Supply LEDsTable 3-1 DC/AC Power Supply PS1-PS3 LED Definitions Figure 3-36 Fan Tray LED Fan Tray LEDFigure 3-37 Cable Management Base Panel LEDs Table 3-2 Fan Tray LED DefinitionsModule LEDs and Reset Button Figure 3-38 Fabric and Control Module LEDs and Reset ButtonControl and Fabric Module LEDs Table 3-3 Control and Fabric Module LED Definitions IOM LEDsTable 3-4 IOM LED Definitions First-Time Quick ConfigurationAssigning an IP Address to eth0 Configuring DHCPEnabling NTP Naming the Matrix X4-C3-44 Matrix X4-C Chassis Setup First-Time Quick ConfigurationSpecifications and Regulatory Compliance Chassis, Power Supply, and Fan Tray SpecificationsTable A-1 Matrix X4-C Specifications Table A-1 Matrix X4-C Specifications continued Power Supply Requirements, Specifications, and Twist Lock OptionsTable A-2 AC Power Supply Requirements Table A-3 Module Power SpecificationsModule Power Specifications continued 10-Gigabit Ethernet Transceiver Specifications XFPRedundancy Configurations for AC Line 100-240 Vac Table A-5 Redundancy Configurations for AC Line 200-240 Vac1-Gigabit Ethernet Transceiver Specifications SFP Table A-8 XFP Fiber-Optic SpecificationsTable A-9 Recommended Cable Types and Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SX SFP Input/Output SpecificationsTable A-10 Mini-GBIC Input/Output Port Specifications Item SpecificationMGBIC-LC09 Specifications 1000BASE-LX MGBIC-LC03 Specifications 1000BASE-SXTable A-13 MGBIC-LC03 Optical Specifications Table A-15 MGBIC-LC09 Optical SpecificationsMGBIC-02 Specifications 1000BASE-T MGBIC-08 Specifications 1000BASE-ELXTable A-17 MGBIC-08 Optical Specifications Table A-19 MGBIC-02 SpecificationsRegulatory Compliance COM Port Pinout AssignmentsFigure A-1 COM Port Pin Assignments Table A-20 COM Port Pin AssignmentsNumerics IndexPage Page Index-4