Manuals / Enterasys Networks / Photography / Camera Accessories

Enterasys Networks X009-U manual Declaration of Conformity

Models: X009-U

1 86

Download 86 pages 56.4 Kb

Page 8

Declaration of Conformity

Application of Council Directive(s): 89/336/EEC 73/23/EEC

Manufacturer’s Name: Enterasys Networks, Inc.

Manufacturer’s Address: 50 Minuteman Road

Andover, MA USA 01810

European Representative Address: Enterasys Networks, Ltd.

Nexus House, Newbury Business Park

London Road, Newbury

Berkshire RG14 2PZ, England

Conformance to Directive(s)/Product Standards: EC Directive 89/336/EEC

EN 55022

EN 61000‐3‐2

EN 61000‐3‐3

EN 55024

EC Directive 73/23/EEC

EN 60950

EN 60825

Equipment Type/Environment: Networking Equipment, for use in a Commercial or Light Industrial Environment.

Enterasys Networks, Inc. declares that the equipment packaged with this notice conforms to the above directives.

vi

Image 8

Enterasys Networks X009-U manual Declaration of Conformity

Contents

Secure Core Router X4-C Chassis Installation GuideEnterasys Matrix Page Enterasys Networks, Inc 50 Minuteman Road Andover, MA Product Safety Regulatory Compliance InformationFederal Communications Commission FCC Notice Industry Canada NoticeElectromagnetic Compatibility EMC Compatibilidad Electromágnetica EMCElektro-magnetische Kompatibilität EMC Hazardous SubstancesSupplement to Product Instructions Safety Information Class 1 Laser Transceivers VCCI NoticeBSMI EMC Statement - Taiwan The single mode interface modules use Class 1 laser transceiversDeclaration of Conformity CAREFULLY READ THIS LICENSE AGREEMENT Enterasys Networks, Inc Firmware License AgreementBEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT 4. EXPORT RESTRICTIONS. You understand that Enterasys and its Affiliates are subject to regulation by agencies of the U.S. Government, including the U.S. Department of Commerce, which prohibit export or diversion of certain technical products to certain countries, unless a license to export the Program is obtained from the U.S. Government or an exception from obtaining such license may be relied upon by the exporting party 10. ENFORCEMENT. You acknowledge and agree that any breach of Sections 2, 4, or 9 of this Agreement by You may cause Enterasys irreparable damage for which recovery of money damages would be inadequate, and that Enterasys may be entitled to seek timely injunctive relief to protect Enterasys’ rights under this Agreement in addition to any and all remedies available at law Page Contents Chapter 2 Site and Configuration GuidelinesChapter 3 Matrix X4-C Chassis Setup About This GuideAppendix A Specifications and Regulatory Compliance IndexFigures Tables Using This Guide About This GuideWho Should Use This Guide For information aboutUsing the Matrix X Router Manual Set Conventions Used in This GuideMatrix X Router Configuration Guide Matrix X Router Command Line Interface Reference GuideCommonly Used Acronyms Getting HelpGetting Help xviii About This GuideOverview System DescriptionFigure 1-1 Matrix X4-C Chassis with Redundant Power Supplies Figure 1-2 Matrix X4-C Chassis as Shipped Rear ViewX4-C Control Module FeaturesX4-C Input/Output Modules Installing Redundant CMs into an Active Matrix X Router 5. Insert the standby CM into the system and wait until it is fully synchronized with the active CM before removing the active CM. Do not physically remove the active CM during the synchronization process. The following message will appear on your console screen Proper CM Recovery X4-C Fabric ModuleX4-C Redundant Power Supplies Power Supply LEDsAuto-Ranging Power Supplies Power Supply ReplacementRack-Mountable Chassis Site and Configuration Guidelines Site Guidelines2-2 Site and Configuration Guidelines Configuration GuidelinesConfiguration Guidelines Matrix X4-C Chassis Setup Required ToolsFigure 3-1 Disassembly Steps 1 and Unpacking the Matrix X4-C ChassisFigure 3-2 Disassembly Steps 3 and Figure 3-3 Disassembly Steps 5 through7. Lift and remove the chassis from the skid Installing the Matrix X4-C Chassis Setting Up the Matrix X4-C ChassisSetup Order Installing Optional Rack Support Brackets Figure 3-4 Installing Rack Support BracketsInstalling Optional Mid-Mount Brackets Figure 3-5 Fastening Mid-Mount BracketsRack Mounting the Matrix X4-C Chassis Figure 3-6 Rack Mounting the Matrix X4-C ChassisChassis Bonding and Grounding Figure 3-7 Rack Mounting the Mid-Mounted ChassisFigure 3-8 Telcordia GR-1089 Grounding Hole Pattern and Cable Figure 3-9 ESD Grounding Receptacle Installing and Removing a Power SupplyAttaching the Electrostatic Discharge Wrist Strap Power Supply Planning Installing a Power SupplyFigure 3-10 Power Supply Planning N + 1 Method Figure 3-11 Power Supply Planning 1 + 1 MethodFigure 3-12 Removing Power Supply Vent Plate Figure 3-13 Installing Power Supply Module Figure 3-14 Removing Coverplate from Power Supply SlotRemoving a Power Supply Figure 3-15 Removing the AC Inlet Power CordFigure 3-16 Removing Fan Tray Bezel Installing and Removing a Fan TrayInstalling a Fan Tray Figure 3-17 Installing Fan Tray Removing a Fan TrayInstalling and Removing Modules Installing and Removing IOMsFigure 3-19 Engaging Ejector Handles Figure 3-18 Installing IOMsFigure 3-20 Removing IOM Coverplate Installing and Removing Modules3-20 Matrix X4-C Chassis Setup MatrixInstalling and Removing CMs Figure 3-21 Installing Control ModuleReplacing the CM Battery All Rights Reserved E7501 & Banias Rev #1.03 PhoenixBIOS 2002 Q31024K Cache SRAM Passed System BIOS shadowed Fixed Disk 0 SAMSUNG CF/ATA ERROR 0271 Check date and time settingsInstalling and Removing FMs Figure 3-22 Installing Fabric ModuleAttaching Cables, Installing Compact Flash Card and DIMM Upgrade Kit Installing an XFP/SFP ModuleRemoving an XFP/SFP Module Connecting Fiber-Optic CablesFigure 3-23 Installing XFP/SFP Optical Transceiver Figure 3-24 Attaching LC or MT-RJ Cable Connector MT-RJConnecting to the CM COM Port Connecting the CM COM Port to an IBM PC or Compatible DeviceConnecting the CM COM Port to a VT Series Terminal Figure 3-25 Connecting an IBM PC or CompatibleConnecting the CM COM Port to a Modem Figure 3-26 Connecting a VT Series TerminalAdapter Wiring and Signal Assignments Figure 3-27 Connecting to a ModemConnecting to the CM USB Port Figure 3-28 Attaching a USB Device to the CM Installing a Compact Flash CardFigure 3-29 Installing Flash Card Figure 3-30 Locating the DIMMs on the CM Installing the Memory Upgrade KitRemoving the DIMMs Installing the DIMMs Figure 3-31 Removing the Existing DIMMInstalling the Cable Management Assembly Optional Cable Management KitFigure 3-32 Installing the Cable Management Assembly Figure 3-33 Securing Cables Using the Velcro Cable StrapsFigure 3-34 Connecting 20 Amp AC Power Cord to the Power Supply Powering Up the Matrix X4-C ChassisLEDs and Reset Button Table 3-1 DC/AC Power Supply PS1-PS3 LED Definitions Power Supply LEDsFigure 3-35 Power Supply LEDs Fan Tray LED Figure 3-36 Fan Tray LEDFigure 3-37 Cable Management Base Panel LEDs Table 3-2 Fan Tray LED DefinitionsControl and Fabric Module LEDs Module LEDs and Reset ButtonFigure 3-38 Fabric and Control Module LEDs and Reset Button IOM LEDs Table 3-3 Control and Fabric Module LED DefinitionsFirst-Time Quick Configuration Table 3-4 IOM LED DefinitionsConfiguring DHCP Assigning an IP Address to eth0Enabling NTP Naming the Matrix X4-CFirst-Time Quick Configuration 3-44 Matrix X4-C Chassis SetupTable A-1 Matrix X4-C Specifications Specifications and Regulatory ComplianceChassis, Power Supply, and Fan Tray Specifications Power Supply Requirements, Specifications, and Twist Lock Options Table A-1 Matrix X4-C Specifications continuedTable A-2 AC Power Supply Requirements Table A-3 Module Power Specifications10-Gigabit Ethernet Transceiver Specifications XFP Module Power Specifications continuedRedundancy Configurations for AC Line 100-240 Vac Table A-5 Redundancy Configurations for AC Line 200-240 VacTable A-9 Recommended Cable Types and Specifications 1-Gigabit Ethernet Transceiver Specifications SFPTable A-8 XFP Fiber-Optic Specifications SFP Input/Output Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SXTable A-10 Mini-GBIC Input/Output Port Specifications Item SpecificationMGBIC-LC03 Specifications 1000BASE-SX MGBIC-LC09 Specifications 1000BASE-LXTable A-13 MGBIC-LC03 Optical Specifications Table A-15 MGBIC-LC09 Optical SpecificationsMGBIC-08 Specifications 1000BASE-ELX MGBIC-02 Specifications 1000BASE-TTable A-17 MGBIC-08 Optical Specifications Table A-19 MGBIC-02 SpecificationsCOM Port Pinout Assignments Regulatory ComplianceFigure A-1 COM Port Pin Assignments Table A-20 COM Port Pin AssignmentsIndex NumericsPage Page Index-4