Adapter Wiring and Signal Assignments | Enterasys Networks X009-U

Attaching Cables, Installing Compact Flash Card and DIMM Upgrade Kit

Figure 3-27 Connecting to a Modem

65

2

4 3 1

STATUS

ACTIVE/

STANDBY

RESET

USB

ETHERNET

COM

1UTP cable with RJ45 connectors

2RJ45 COM port

3RJ45-to-DB25 modem adapter

4Local modem

5Remote modem

6IBM PC or compatible device

Adapter Wiring and Signal Assignments

	COM Port Adapter Wiring and Signal Diagram

	RJ45							DB9

	Pin					Conductor		Pin		Signal

1						Blue		2		Receive (RX)

4						Red		3		Transmit (TX)

5						Green		5		Ground (GRD)

2						Orange		7		Request to Send (RTS)

6						Yellow		8		Clear to Send (CTS)

				Pins						5	Pins				1
1						8
1						8
										9					6



	RJ45 Connector (Female)

								DB9		Connector					(Female)
								DB9		Connector					(Female)

3-30 Matrix X4-C Chassis Setup

Image 60

Enterasys Networks X009-U manual Adapter Wiring and Signal Assignments, COM Port Adapter Wiring and Signal Diagram RJ45

Contents

Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys Networks, Inc Firmware License Agreement Viii Page Page Contents Appendix a Specifications and Regulatory Compliance Index Figures Tables Using This Guide Who Should Use This GuideFor information about Refer to Using the Matrix X Router Manual Set Conventions Used in This Guide Commonly Used Acronyms Getting Help Getting Help Xviii About This Guide Overview System Description Matrix X4-C Chassis with Redundant Power Supplies Features X4-C Input/Output ModulesX4-C Control Module Installing Redundant CMs into an Active Matrix X Router CM1 X4-C Fabric Module Monitor Values X4-C Redundant Power Supplies Power Supply LEDsAuto-Ranging Power Supplies Power Supply Replacement Rack-Mountable Chassis Site and Configuration Guidelines Site Guidelines Configuration Guidelines Matrix X4-C Chassis Setup Required Tools Unpacking the Matrix X4-C Chassis Shipping straps Shipping box Shipping skid Disassembly Steps 3 Unpacking the Matrix X4-C Chassis Setting Up the Matrix X4-C Chassis Setup OrderInstalling the Matrix X4-C Chassis Installing Optional Rack Support Brackets Rack Rack support brackets Bracket screws Installing Optional Mid-Mount Brackets Fastening Mid-Mount Brackets Rack Mounting the Matrix X4-C Chassis Rack Mounting the Matrix X4-C Chassis Chassis Bonding and Grounding Rack Mounting the Mid-Mounted Chassis AWG stranded copper wire Chassis 4-20 ground screws Telcordia GR-1089 Grounding Hole Pattern and Cable Installing and Removing a Power Supply Attaching the Electrostatic Discharge Wrist StrapGrounding Receptacle Plug Wrist strap Power Supply Planning Installing a Power Supply 12 Removing Power Supply Vent Plate 13 Installing Power Supply Module 14 Removing Coverplate from Power Supply Slot Removing a Power Supply Inlet power cord AC inlet AC1 Installing and Removing a Fan Tray Installing a Fan TrayFan tray bezel IOM slot Removing a Fan Tray Fan tray slot Installing and Removing Modules Installing and Removing IOMs 18 Installing IOMs 20 Removing IOM Coverplate IOM slot IOM coverplate Captive screws IOM guide rails Installing and Removing CMs 21 Installing Control Module Replacing the CM Battery Installing and Removing FMs 22 Installing Fabric Module Installing an XFP/SFP Module Connecting Fiber-Optic Cables Removing an XFP/SFP ModuleXFP transceiver Port slot Release handle SFP transceiver MT-RJ Connecting to the CM COM Port Parameter Setting Connecting the CM COM Port to a VT Series Terminal 25 Connecting an IBM PC or Compatible Connecting the CM COM Port to a Modem 26 Connecting a VT Series Terminal Adapter Wiring and Signal Assignments COM Port Adapter Wiring and Signal Diagram RJ45 Connecting to the CM USB Port VT Series Port Adapter Wiring and Signal Diagram RJ45 DB25Modem Port Adapter Wiring and Signal Diagram RJ45 DB25 Installing a Compact Flash Card Compact Flash card Connector Control ModuleUSB device Control Module USB port Installing the Memory Upgrade Kit Removing the DIMMs Installing the DIMMs Connector fingers Connector arms Installing the Cable Management Assembly Optional Cable Management Kit 32 Installing the Cable Management Assembly Powering Up the Matrix X4-C Chassis LEDs and Reset Button Power Supply LEDs DC/AC Power Supply PS1-PS3 LED DefinitionsFunction LED Activity DC Power LED AC Power LED Fan Tray LED Fan Tray LED DefinitionsFunction LED Activity Module LEDs and Reset Button Control and Fabric Module LEDsFabric Module Control Module IOM LEDs Control and Fabric Module LED DefinitionsCM & FM LEDs State LED Activity CM LEDs Only State LED Activity First-Time Quick Configuration IOM LED DefinitionsStatus LED LED Activity Ethernet Port LED RX/TX LED Activity Configuring Dhcp Assigning an IP Address to eth0Enabling NTP Naming the Matrix X4-C First-Time Quick Configuration Matrix X4-C Chassis Setup Chassis, Power Supply, and Fan Tray Specifications Table A-1 Matrix X4-C SpecificationsSpecification AC Power Supply Module Table A-2 AC Power Supply Requirements Table A-3 Module Power Specifications Gigabit Ethernet Transceiver Specifications XFP Module Power SpecificationsRedundancy Configurations for AC Line 100-240 Vac Table A-5 Redundancy Configurations for AC Line 200-240 Vac Gigabit Ethernet Transceiver Specifications SFP Table A-8 XFP Fiber-Optic SpecificationsTable A-9 Recommended Cable Types and Specifications SFP Input/Output Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SX MGBIC-LC03 Specifications 1000BASE-SX MGBIC-LC09 Specifications 1000BASE-LX MGBIC-08 Specifications 1000BASE-ELX MGBIC-02 Specifications 1000BASE-TTable A-17 MGBIC-08 Optical Specifications 10 µm SMF Table A-19 MGBIC-02 Specifications Pin Signal Name Input/Output COM Port Pinout AssignmentsRegulatory Compliance Table A-20 COM Port Pin Assignments Index MT-RJ NTP Index-4