Standard Output Connections | Extron electronic ISM 482 guide

Standard Output Connections

NOTE: The two Output 1 outputs, consisting of five BNC connectors and a 15‑pin HD connector, output the identical video signal and the same sync format. The two Output 2 outputs are also identical to each other.

DVideo output BNC connectors — Connect RGB video displays to these two sets of female BNC connectors. Figure 7 shows how to connect the various video formats.

RR

GG

BB

H/HVHV

VV

RGBHV RGBS

Video Video

Figure 7. BNC Output Connections for RGBHV and RGBS Video

Video output 15-pin HD connectors — Connect RGB video displays to these two female 15-pin HD connectors.

EAudio output connectors — Connect audio devices, such as an audio amplifier or powered speakers, to these two 3.5 mm, 5-pole captive screw connectors. The connectors output the selected unamplified, line level audio. See figure 8 to properly wire an output connector.

No Ground Here

Tip

Sleeves

Tip

Do not tin the wires!

	L	Tip	L
		Ring
		Sleeves
	R	Tip	R
	R	Ring	R
		Ring

No Ground Here	Balanced Stereo Output
Unbalanced Stereo Output

Figure 8. Captive Screw Connector Wiring for Audio Output

ATTENTION:

•Connect the sleeve to ground (Gnd). Connecting the sleeve to a negative (-) terminal will damage the audio output circuits.

•The length of exposed wires is critical. The ideal length is 0.2 inches (5 mm).

•If the stripped section of wire is longer than 0.2 inches, the exposed wires may touch, causing a short circuit between them.

•If the stripped section of wire is shorter than 0.2 inches, wires can be easily pulled out even if tightly fastened by the captive screws.

By default, the audio output follows the video switch. Audio breakaway, commanded via the front panel, the Ethernet link, or the RS-232 link, allows you to select from any one of the audio input sources. See the applicable portions of the Operation section (see page 12), Programming Guide section (see page 38), Switcher Software section (see page 50), and HTML Operation section (page 55).

ISM 482 Integrated Scaling Matrix Switcher • Installation

8

Image 14

Extron electronic ISM 482 manual Standard Output Connections, BNC Output Connections for Rgbhv and Rgbs Video

Contents

ISM No Photo Available yet Safety Instructions Notifications Specifications Availability Conventions Used in this GuideFCC Class a Notice Software Commands X! *X1@* X1%* X1** X1 CE Contents Ethernet Connection Switcher SoftwareHtml Operation Reference Information About This Guide About the SwitcherIntroduction ISM Features Inputs ISM 482 Integrated Scaling Matrix Switcher Introduction Tabletop Placement InstallationMounting the Switcher Rack Mounting Cabling and Rear Panel Views Input Connections Connections for Various Input Video Formats Standard Output Connections BNC Output Connections for Rgbhv and Rgbs Video Ethernet Connection Cabling and RJ-45 connector wiringOptional Output Connection Choosing a network cable RS-232 Connection ConfigurationWiring the network cable Pin RS-232 Function Front Panel Controls and Indicators Operation Video/Audio Selection Button and LEDs Output Buttons and LEDs Front panel input label window Recalling a user presetInput Buttons, LEDs, and Label Window Selecting an input Auto imaging an input Picture Adjustment ButtonsBlack/Mute Button and LEDs Front Panel Operations Adjustment KnobsPower LCD Display Menu System Overview Extron Electronics ISM 60-425-01 Version Video & Audio Configuration menu Input Configuration submenu Output Configuration menu Output Resolution submenu Sync Type and Polarity submenu Advanced Configuration Menu 000 Test Pattern submenu Blue-Only Mode and Edge Smoothing submenuRGB Delay submenu Blanking submenu PAL Film Mode submenu Enhanced Mode submenuPixel Phase submenu Reset submenu User Presets menu Save Preset submenu Erase Preset submenu Exit menu Picture Adjustments Picture Adjustments Flowchart Front Panel Security Lockout Executive Mode Front Panel Security Lockout Flowchart IP Information Flowchart IP Information Optimizing the Video Optimizing the Audio TroubleshootingSetting up a DVD source Specific Problems General Checks Programming Guide RS-232 Link Default Address Ethernet Link Symbols = Hdtv Ties Creation Switcher-Initiated MessagesPower-up Input and Output Video Type @BrtX1 Automated Adjustments RGB DelayPAL Film Mode Test Pattern Using the Command and Response Table Host-to-Switcher InstructionsSwitcher Error Responses Command and Response Table for SIS Commands Contrast TintBrightness Horizontal size Command and Response Table for SIS Commands Auto Memories User presetsDetail filter S-video and composite video inputs Freeze Set audio gain and attenuation Front panel security lockout Executive modeVerbose mode Audio mute Resets Information requests Command and response table Command and Response Table for IP SIS CommandsSymbol definitions Enhanced mode RGB delayScaler output settings PAL film mode Memory backup Control Software for Windows Switcher SoftwareInstalling the Software Ethernet protocol settings Software Operation via Ethernet Using the Control Program If you selected a comm port, proceed to step Windows Control Program Window Using the Help Program Button-Label Generator Using the Software Extron Button-Label Generator Window Html Operation Loading the Startup Control Enter Network Password Creating a Tie Changing the RGB DelayControl Blacking out the Screen and Muting the Audio Freezing the Output Using Blue-Only ModeExecutive Mode Outputting a Test Pattern System Configuration Administration Fields ISM Name field ISM IP Settings FieldsISM IP Address field Hardware Address field File Management File Management Input Configuration O Configuration Output Resolution, Rate, Sync Format, and Polarity Output format Output resolutionOutput rate Output polarity Polarity Drop Box Maintenance Modifications Opening and Closing the Switcher Removing the ISM Cover Installing a Firmware Upgrade ISM Firmware Chip Locations Installing a DVI Output Card DVI Output Card Connector Opening and Socket J14 Output DVI Board Installation Ethernet Connection Cabling Pinging to Determine the Web IP Address Determining Default AddressesPinging to Determine the Switcher IP Address Open Connecting as a Telnet ClientTelnet Tips Set carriage return-line feed Escape character and Esc keyLocal echo Close Part Numbers Optional AccessoriesReference Information Included Parts Button Labels Cables and ConnectorsAssorted connectors Bulk cablePage Extron Warranty USA, Canada, South America Central America Japan