Command and Response Table for Special Function SIS Commands

The syntax for setting a special function is X/*X?# where X/ is the value or variable (such as 35 in the first example below), X/ is the function number (such as “set RGB delay” in the first example below), and # is the execute command. To view the setting of a function, use X? # where X? is the function number.

Command Function

SIS Command

Response

Additional description

 

(Host to Unit)

(Unit to Host)

 

RGB delay

RGB delay (Triple-Action Switching)

X2)*3#

DlyX2)]

Example:

35*3#

Dly35]

Switching delay of the selected input to the preview output. Adjustable in 0.01 second steps from 0 up to 50 = 5.0 seconds. 0 = 0.0 seconds (default), 1 = 0.1 seconds, 2 = 0.2 seconds, and so on.

RGB delay set to 3.5 seconds.

Scaler output settings

Output sync format

X**6#

SynX*]

00 = RGBHV (default)

01 = RGBS

Example:

1*6#

Syn1]

RGBHV output signal.

 

Output polarity

X(*7#

PolX(]

X(: Horizontal/Vertical polarity

 

 

 

0

= H–/V–

 

2 = H+/V–

 

 

 

1

= H–/V+

 

3 = H+/V+

Example:

1*7#

Pol1]

H–/V+ output polarity.

 

Blue screen

 

 

 

 

 

 

Blue screen (blue & sync output only)

X#*8#

BluX#]

0 = off (normal output).

 

 

 

 

1 = on (blue video and sync output).

Example:

1*8#

Blu1]

Blue and sync output for setup.

Edge smoothing

 

 

 

 

 

 

Edge smoothing

X#*16#

FilX#]

00 = off

01 = on (default)

Example:

1*16#

Fil01]

Enable edge smoothing.

 

 

 

 

 

 

 

 

Enhanced mode

 

 

 

 

 

 

Enhanced mode

X#*12#

EnhX#]

0 = off.

 

1 = on.

Example:

1*12#

Enh01]

Enable enhanced mode.

 

 

 

 

 

 

 

 

Auto Image

 

 

 

 

 

 

Set Auto Image

X#*13#

ImgX#]

00 = off

 

01 = on

Example:

1*13#

Img01]

Set Auto Image on.

 

 

Execute Auto Image

X1**14#

ImgX1*]

X1*: Auto Image input tied to output:

 

 

 

 

Out 1/Out 2

 

Out 1/Out 2

 

 

 

 

01 = Yes/No

 

03 = Yes/Yes

 

 

 

 

02 = No/Yes

 

 

 

 

X@Reconfig]

Output X@ Auto Image is complete.

 

 

X@Reconfig]

Output X@ Auto Image is complete.

NOTES:

If Auto Image adjustments are not necessary for an input, the X@Reconfig] message may not be received.

If both outputs are receiving the same input, both outputs are auto imaged regardless of the X1* received.

PAL film mode

Set PAL film

mode

X!*X#*18#

X!FlmX#]

Example:

 

8*1*18#

8Flm01]

Read PAL film

mode

X!*18#

X#]

X#: 0 = off (default) 1 = on

The ISM uses its 2:2 pulldown (PAL) video processing algorithms to scale input 8.

0 = off

1 = on.

ISM 482 Integrated Scaling Matrix Switcher • Programming Guide 45

Page 51
Image 51
Extron electronic ISM 482 manual RGB delay, Scaler output settings, Blue screen, Edge smoothing, Enhanced mode, Auto Image