Manuals / Fisher & Paykel / Laundry Appliance / Washer

Fisher & Paykel 517735 Phase 1 to 5 Bowl Engaged During Agitate, Primary Source Mechanical Action

Models: 517735

1 92

Download 92 pages 53.84 Kb

Page 65

160.(10100000) Phase 1 to 5 - Bowl Engaged During Agitate

The bowl has re-engaged itself during agitate. Possible causes for this are a leak in the air bell, bowl is over-loaded with clothes, the clutch has jammed or is fouled with a foreign object.

Primary Source - Mechanical

Action

1.Make sure the bowl is not overloaded with too many clothes.

2.Check that the rotating bowl assembly is not jammed to the agitator with any foreign object that may be caught under the agitator skirt.

3.Check that the clutch teeth are not locked together with dirt, lint, etc.

4.If none of the above appear to be at fault, then check the air bell at the bottom of the inner bowl for leaks.

Secondary Source - Motor Controller (Phase 1 to 4 Only).

Action - If Smartdrive is empty of water when faulting it is possible that the pump circuit is faulty and has caused a pump out during wash. This would cause the bowl to re-engage during agitate and the Motor Controller to display this fault. Replace Motor Controller.

161.(10100001) Phase 2 to 5 – Motor Controller Fault

The Motor Controller checks the voltage configuration (i.e. 110v or 230V) against its EEPROM on power up. Should there be a mismatch, this error is flagged.

Primary Source - Motor Controller Action - Replace Motor Controller.

162.(10100010) Phase 3 to 5 Brake Deceleration Time-out Fault

During the brake mode the Motor Controller has detected that the bowl has not come to a stop in the permitted time once dropping below 100 RPM. This fault has been installed for software testing only.

163.(10100011) Phase 4 to 5 - Motor Controller Fault

The Motor Controller has internally sensed a connection is open circuit. The cold valve cannot be operated with this condition.

Primary Source - Motor Controller. Action - Replace Motor Controller.

- 60 -

Image 65

Fisher & Paykel 517735 service manual Phase 1 to 5 Bowl Engaged During Agitate, Primary Source Mechanical Action

Contents

Smart Drive Electronic Washing Machine Phase 1 to 5 Phase 4 GW Phase 3 GWPhase 5 IW Phase 5 Iweco MW, GW What PHASE, Size & Model is Your SMARTDRIVE? Table of Contents Recycle Introduction HOW to Service SmartdriveIf Smartdrive has no Power see Section Smartdrive Servicing Quick Reference Guide ALL Terminals and Internal Parts should be Treated AS Live Specifications Installation InstallationRemoving Transit Restraint Inlet Hoses Safety Installation Environment Water Supply TemperaturesAccessories and Spare Parts Levelling Smartdrive Smartdrive Components Electronics Systems Phase Wiring Diagram Motor Specifications Water Level Measurement Pressure Sensor Motor Controller Module Display Module Water Valves Rotor Position Sensor Installation Pump Pump Motor Specifications Inner and Outer Bowls Diagram showing the Floating Bowl Detection Of Inner Bowl Float Off Point Bowl Check Lid Switch Lid Switch and Out of Balance Switch Water Temperature Sensing Smartdrive Information Favourite cycle GW only All PhasesCustomising Wash Cycles GW only Phase 3 to 5 only Water Saver GW only Phase 3 to 5 only Delay Start GW only Phase 2 to 5 onlyAuto Water Level GW only Phase 3 to 5 only Amount of Water Used in the Water Saver Rinse Fabric Softener Dispenser All Phases Creasing Wash Performance Information All Phases If Smartdrive Powers Off mid cycle Smartdrive ProblemsIf Smartdrive Appears To Have No Power Noisy FloodingLeaking Poor Wash Performance Continuous Spinning or Slow Spinning Radio Frequency Interference RFI SiphoningEarth Leakage It Appears Smartdrive is doing nothing Wash Water Temperature All Phases Option Adjustment Mode Method of Setting the Wash Temperature Rinse Options All Phases Phase End of Cycle Warning Beeps GW Only All Phases Out Of Balance Recovery Adjustment GW and MW only Phase Auto Water Fill Level Adjustment GW only Phase What WAS the Last FAULT? Diagnostic Mode To Test Pump & Water Valves Test LID, OUT of BALANCE, & Size Switches Recycle RestartLOW Water Level LED OFF = Restart OFF Medium Water Level LED on = RE-CYCLE onPage Size Setting Mode Phase 4 and 5 only Insufficient Cold Water Cold Water LED flashing User WarningsInsufficient Hot Water Hot Water LED flashing Overloaded Product High Water LED flashing No Water Both Hot and Cold Water LEDs flashing Restart and Recycle Wash Progress LEDs flashing Phase 4Phase 1 to Demonstration Mode All LEDs flashing in patterns GWC08 GWM08 GWL08 THC08 THM08 THL08 Fault CodesGWC09 GWM09 GWL09 IWM09 IWL09 Phase 1 to 5 Motor Controller Fault Smartdrive Phases 1 to 5 Fault DescriptionsPhase 1 Communications Fault Primary Source Motor Controller Phase 1 to 5 Size Error Phase 1 to 5 Display Module FaultPrimary Source Display Module Action Primary Source Display Module Phase 1 to 5 Thermistor Error Phase 4 toAction Phase Phase 2 to Phase 1 to 5 Flood Protection Error Phase 1 to 5 Pressure Sensor FaultPhase 1 Pump Fault Primary Source Pressure Tube Phase 5 IW LCD Initialisation Error Phase 1 Pump Connection Fault28 30 xx Phase 1 Display / Motor Controller out of Sequence Primary Source Pump Action Phase 1 MC Reset Error Phase 1 Pump Circuit ErrorPhase 1 Brake Resistor Fault Phase 1 to 5 Pump Block Error Phase 1 to 5 Water Leak FaultPrimary Source Pump System Secondary Source Mechanical Action Phase 1 to 5 Bowl Dis-Engaged Fault Phase 1 to 5 Tap or Pressure Sensor Tube FaultPrimary Source Mechanical Primary Source Suds Phase 1 Rotor Fault Primary Source Phase 1 to 5 Temperature Sensor FaultPhase 1 to 5 OOB Switch Fault Primary Source Mechanical Action Phase 5 Display Fault Phase 2 to 5 Water in Bowl During SpinPrimary Source Pump System Action Secondary Source Motor Controller Phase 2 to 5 Hot and Cold Valve Fault Phase 2 to 3 Bowl Dis-engaged FaultPrimary Source Wiring Phase 2 to 5 Cold Valve Fault Phase 5 ECO Recirculation Fault Phase 2 to 5 Hot Valve FaultPhase 5 ECO Recirculation Fault See fault code Secondary Source Diverter Valve Secondary Source Motor Phase 2 to 5 Rotor Position Sensor FaultPhase 2 to 5 Motor / Motor Control Step Fail Phase 4 to 5 Motor Controller Fault Phase 4 to 5 Bowl Check Fault Primary Source- Pump Phase 4 Motor Controller Fault Phase 5 Machine Setup Error Phase 2 to 3 Display / Motor Controller Comms. Error Primary Source Wiring Action Phase 1 to 5 Single Rotor Position Sensor Error Phase 1 to 4 Single Current Trip Phase 1 to 5 Repetitive Rotor Position Sensor ErrorPhase 1 to 4 Repetitive Current Trip Phase 4 Single Current Trip & Rotor Position Sensor Error Phase 1 to 5 Motor Stall Phase 1 to 5 Bowl Engaged During Agitate Phase 4 to 5 Brake Function Time-out Fault Phase 5 Topdeck Showing Wiring Connections Mechanical Service SectionComplete Disassembly NB DON’T Remove the Earth Connection from the Wrapper Phase 2 Topdeck Showing Wiring ConnectionsPage Page Assembly Guidelines Assembly Motor Assembly & Disassembly Pump Blockage Shaft & Bearing Removal Shaft & Bearing Assembly Page Wash Progress LEDs Appendix a Binary Decoding Chart 8 Bits Important Note Size SettingFault Finding / Fault Codes Pump Hood Kit Part Number 479188P WM013 Pump Hood KIT January 2000 Phases 2 toWiring Connections WM51 Diagnostic Flow Chart Sept 1992- Phase 1 only Kit Lever Out of Balance & Bracket Phase 2 Part Number WM65 BIB Deflector April 1994- Phase 1 onlyWM70 Premature OUT of Balance February 1995 Phase 2 only WM81 Pump Shield 5KG Smartdrive September 1996 Phases 1 to WM80 Condensation KIT May 1996 Phase 2 & 3 only Appendix C Smarttool Appendix D Tools for Servicing Smartdrive IW Quick Reference Guide Specifications for IWModels Size Width Wash Load Capacity Compact Medium Large Wash 1 Detergent Activating Wash Front loader type wash Introduction to IW Water Temperature Sensing Pump Option Adjustment Mode for IW Other Options Status Display Diagnostic Mode for IW Fault Status Recycle Size Setting Mode for IW