Manuals / Fisher & Paykel / Laundry Appliance / Washer

Fisher & Paykel 517735 service manual Phase 4 to 5 Brake Function Time-out Fault

Models: 517735

1 92

Download 92 pages 53.84 Kb

Page 66

164.(10100100) Phase 4 to 5 - Brake Function Time-out Fault

This fault indicates that the Motor Controller has been attempting to brake for 20 seconds. All spin loads should come to rest within 10 seconds something must have gone wrong during the brake to prevent the bowl stopping in time.

Primary Source - Wiring

Action - Measure/check the motor harness, connectors and motor for discontinuity. This can be done by taking a resistance measurement between phases of the motor harness at the Motor Controller.

Secondary Source - Motor Controller (Phase 4). Rotor Position Sensor (Phase 5) Action - Replace Motor Controller (Phase 4). Rotor Position Sensor (Phase 5)

192.(11000000) Phase 4 to 5 – Motor Controller Fault

The Motor Controller has internally sensed a connection is open circuit. The motor cannot be operated with this condition.

Primary Source - Motor Controller Action - Replace Motor Controller.

- 61 -

Image 66

Fisher & Paykel 517735 service manual Phase 4 to 5 Brake Function Time-out Fault

Contents

Phase 1 to 5 Smart Drive Electronic Washing Machine Phase 5 IW Phase 3 GWPhase 4 GW Phase 5 Iweco What PHASE, Size & Model is Your SMARTDRIVE? MW, GW Table of Contents Recycle HOW to Service Smartdrive If Smartdrive has no Power see SectionIntroduction Smartdrive Servicing Quick Reference Guide Specifications ALL Terminals and Internal Parts should be Treated AS Live Removing Transit Restraint InstallationInstallation Inlet Hoses Accessories and Spare Parts Installation Environment Water Supply TemperaturesSafety Levelling Smartdrive Smartdrive Components Electronics Systems Phase Wiring Diagram Specifications Motor Motor Controller Module Water Level Measurement Pressure Sensor Display Module Water Valves Installation Rotor Position Sensor Pump Motor Specifications Pump Diagram showing the Floating Bowl Inner and Outer Bowls Detection Of Inner Bowl Float Off Point Bowl Check Lid Switch and Out of Balance Switch Lid Switch Water Temperature Sensing Favourite cycle GW only All Phases Customising Wash Cycles GW only Phase 3 to 5 onlySmartdrive Information Delay Start GW only Phase 2 to 5 only Auto Water Level GW only Phase 3 to 5 onlyWater Saver GW only Phase 3 to 5 only Fabric Softener Dispenser All Phases Amount of Water Used in the Water Saver Rinse Wash Performance Information All Phases Creasing Smartdrive Problems If Smartdrive Appears To Have No PowerIf Smartdrive Powers Off mid cycle Flooding LeakingNoisy Continuous Spinning or Slow Spinning Poor Wash Performance Earth Leakage SiphoningRadio Frequency Interference RFI It Appears Smartdrive is doing nothing Option Adjustment Mode Wash Water Temperature All Phases Rinse Options All Phases Method of Setting the Wash Temperature End of Cycle Warning Beeps GW Only All Phases Phase Auto Water Fill Level Adjustment GW only Phase Out Of Balance Recovery Adjustment GW and MW only Phase Diagnostic Mode What WAS the Last FAULT? Test LID, OUT of BALANCE, & Size Switches To Test Pump & Water Valves LOW Water Level LED OFF = Restart OFF RestartRecycle Medium Water Level LED on = RE-CYCLE onPage Size Setting Mode Phase 4 and 5 only User Warnings Insufficient Hot Water Hot Water LED flashingInsufficient Cold Water Cold Water LED flashing No Water Both Hot and Cold Water LEDs flashing Overloaded Product High Water LED flashing Phase 4 Phase 1 toRestart and Recycle Wash Progress LEDs flashing Demonstration Mode All LEDs flashing in patterns GWC09 GWM09 GWL09 Fault CodesGWC08 GWM08 GWL08 THC08 THM08 THL08 IWM09 IWL09 Phase 1 Communications Fault Smartdrive Phases 1 to 5 Fault DescriptionsPhase 1 to 5 Motor Controller Fault Primary Source Motor Controller Primary Source Display Module Action Phase 1 to 5 Display Module FaultPhase 1 to 5 Size Error Primary Source Display Module Action Phase Phase 4 toPhase 1 to 5 Thermistor Error Phase 2 to Phase 1 Pump Fault Phase 1 to 5 Pressure Sensor FaultPhase 1 to 5 Flood Protection Error Primary Source Pressure Tube 28 30 xx Phase 1 Display / Motor Controller out of Sequence Phase 1 Pump Connection FaultPhase 5 IW LCD Initialisation Error Primary Source Pump Action Phase 1 Pump Circuit Error Phase 1 Brake Resistor FaultPhase 1 MC Reset Error Primary Source Pump System Phase 1 to 5 Water Leak FaultPhase 1 to 5 Pump Block Error Secondary Source Mechanical Action Primary Source Mechanical Phase 1 to 5 Tap or Pressure Sensor Tube FaultPhase 1 to 5 Bowl Dis-Engaged Fault Primary Source Suds Phase 1 to 5 OOB Switch Fault Phase 1 to 5 Temperature Sensor FaultPhase 1 Rotor Fault Primary Source Primary Source Mechanical Action Primary Source Pump System Action Phase 2 to 5 Water in Bowl During SpinPhase 5 Display Fault Secondary Source Motor Controller Primary Source Wiring Phase 2 to 3 Bowl Dis-engaged FaultPhase 2 to 5 Hot and Cold Valve Fault Phase 2 to 5 Cold Valve Fault Phase 5 ECO Recirculation Fault See fault code Phase 2 to 5 Hot Valve FaultPhase 5 ECO Recirculation Fault Secondary Source Diverter Valve Phase 2 to 5 Rotor Position Sensor Fault Phase 2 to 5 Motor / Motor Control Step FailSecondary Source Motor Phase 4 to 5 Bowl Check Fault Phase 4 to 5 Motor Controller Fault Phase 4 Motor Controller Fault Primary Source- Pump Phase 2 to 3 Display / Motor Controller Comms. Error Phase 5 Machine Setup Error Phase 1 to 5 Single Rotor Position Sensor Error Primary Source Wiring Action Phase 1 to 4 Repetitive Current Trip Phase 1 to 5 Repetitive Rotor Position Sensor ErrorPhase 1 to 4 Single Current Trip Phase 4 Single Current Trip & Rotor Position Sensor Error Phase 1 to 5 Motor Stall Phase 1 to 5 Bowl Engaged During Agitate Phase 4 to 5 Brake Function Time-out Fault Mechanical Service Section Complete DisassemblyPhase 5 Topdeck Showing Wiring Connections Phase 2 Topdeck Showing Wiring Connections NB DON’T Remove the Earth Connection from the WrapperPage Page Assembly Guidelines Motor Assembly & Disassembly Assembly Pump Blockage Shaft & Bearing Removal Shaft & Bearing Assembly Page Appendix a Binary Decoding Chart 8 Bits Wash Progress LEDs Size Setting Fault Finding / Fault CodesImportant Note WM013 Pump Hood KIT January 2000 Phases 2 to Wiring ConnectionsPump Hood Kit Part Number 479188P WM51 Diagnostic Flow Chart Sept 1992- Phase 1 only WM65 BIB Deflector April 1994- Phase 1 only WM70 Premature OUT of Balance February 1995 Phase 2 onlyKit Lever Out of Balance & Bracket Phase 2 Part Number WM80 Condensation KIT May 1996 Phase 2 & 3 only WM81 Pump Shield 5KG Smartdrive September 1996 Phases 1 to Appendix C Smarttool Appendix D Tools for Servicing Smartdrive Models Size Width Wash Load Capacity Specifications for IWIW Quick Reference Guide Compact Medium Large Introduction to IW Wash 1 Detergent Activating Wash Front loader type wash Water Temperature Sensing Option Adjustment Mode for IW Pump Other Options Diagnostic Mode for IW Status Display Fault Status Size Setting Mode for IW Recycle