Manuals / Fisher & Paykel / Laundry Appliance / Washer

Fisher & Paykel 517735 service manual

Models: 517735

1 92

Download 92 pages 53.84 Kb

Page 70

14.Lay the cabinet on its back, on protective material, and slide the outer bowl assembly out, but note that approximately 1 litre of water must be removed from the pump sump before laying the cabinet on its back.

15. To remove the pump, release the locking tab. Turn the pump anti-clockwise, lift it clear and remove the electrical connections.

16. Remove the two screws securing the wiring duct to the outer bowl base.

17. Remove the drain hose clamp. Twist the drain hose in an anti-clockwise direction to release the bayonet fitting. If changing the outer bowl, the pump securing plate can be removed at this stage by unscrewing the 4 x 3/8" securing bolts.

18. Remove the clamp from the pressure tube and pull the tube off the spigot on the pressure chamber.

19. Unclip the pump harness and then remove the complete assembly.

- 65 -

Image 70

Fisher & Paykel 517735 service manual

Contents

Phase 1 to 5 Smart Drive Electronic Washing Machine Phase 5 IW Phase 3 GWPhase 4 GW Phase 5 Iweco What PHASE, Size & Model is Your SMARTDRIVE? MW, GW Table of Contents Recycle If Smartdrive has no Power see Section HOW to Service SmartdriveIntroduction Smartdrive Servicing Quick Reference Guide Specifications ALL Terminals and Internal Parts should be Treated AS Live Removing Transit Restraint InstallationInstallation Inlet Hoses Accessories and Spare Parts Installation Environment Water Supply TemperaturesSafety Levelling Smartdrive Smartdrive Components Electronics Systems Phase Wiring Diagram Specifications Motor Motor Controller Module Water Level Measurement Pressure Sensor Display Module Water Valves Installation Rotor Position Sensor Pump Motor Specifications Pump Diagram showing the Floating Bowl Inner and Outer Bowls Detection Of Inner Bowl Float Off Point Bowl Check Lid Switch and Out of Balance Switch Lid Switch Water Temperature Sensing Customising Wash Cycles GW only Phase 3 to 5 only Favourite cycle GW only All PhasesSmartdrive Information Auto Water Level GW only Phase 3 to 5 only Delay Start GW only Phase 2 to 5 onlyWater Saver GW only Phase 3 to 5 only Fabric Softener Dispenser All Phases Amount of Water Used in the Water Saver Rinse Wash Performance Information All Phases Creasing If Smartdrive Appears To Have No Power Smartdrive ProblemsIf Smartdrive Powers Off mid cycle Leaking FloodingNoisy Continuous Spinning or Slow Spinning Poor Wash Performance Earth Leakage SiphoningRadio Frequency Interference RFI It Appears Smartdrive is doing nothing Option Adjustment Mode Wash Water Temperature All Phases Rinse Options All Phases Method of Setting the Wash Temperature End of Cycle Warning Beeps GW Only All Phases Phase Auto Water Fill Level Adjustment GW only Phase Out Of Balance Recovery Adjustment GW and MW only Phase Diagnostic Mode What WAS the Last FAULT? Test LID, OUT of BALANCE, & Size Switches To Test Pump & Water Valves LOW Water Level LED OFF = Restart OFF RestartRecycle Medium Water Level LED on = RE-CYCLE onPage Size Setting Mode Phase 4 and 5 only Insufficient Hot Water Hot Water LED flashing User WarningsInsufficient Cold Water Cold Water LED flashing No Water Both Hot and Cold Water LEDs flashing Overloaded Product High Water LED flashing Phase 1 to Phase 4Restart and Recycle Wash Progress LEDs flashing Demonstration Mode All LEDs flashing in patterns GWC09 GWM09 GWL09 Fault CodesGWC08 GWM08 GWL08 THC08 THM08 THL08 IWM09 IWL09 Phase 1 Communications Fault Smartdrive Phases 1 to 5 Fault DescriptionsPhase 1 to 5 Motor Controller Fault Primary Source Motor Controller Primary Source Display Module Action Phase 1 to 5 Display Module FaultPhase 1 to 5 Size Error Primary Source Display Module Action Phase Phase 4 toPhase 1 to 5 Thermistor Error Phase 2 to Phase 1 Pump Fault Phase 1 to 5 Pressure Sensor FaultPhase 1 to 5 Flood Protection Error Primary Source Pressure Tube 28 30 xx Phase 1 Display / Motor Controller out of Sequence Phase 1 Pump Connection FaultPhase 5 IW LCD Initialisation Error Primary Source Pump Action Phase 1 Brake Resistor Fault Phase 1 Pump Circuit ErrorPhase 1 MC Reset Error Primary Source Pump System Phase 1 to 5 Water Leak FaultPhase 1 to 5 Pump Block Error Secondary Source Mechanical Action Primary Source Mechanical Phase 1 to 5 Tap or Pressure Sensor Tube FaultPhase 1 to 5 Bowl Dis-Engaged Fault Primary Source Suds Phase 1 to 5 OOB Switch Fault Phase 1 to 5 Temperature Sensor FaultPhase 1 Rotor Fault Primary Source Primary Source Mechanical Action Primary Source Pump System Action Phase 2 to 5 Water in Bowl During SpinPhase 5 Display Fault Secondary Source Motor Controller Primary Source Wiring Phase 2 to 3 Bowl Dis-engaged FaultPhase 2 to 5 Hot and Cold Valve Fault Phase 2 to 5 Cold Valve Fault Phase 5 ECO Recirculation Fault See fault code Phase 2 to 5 Hot Valve FaultPhase 5 ECO Recirculation Fault Secondary Source Diverter Valve Phase 2 to 5 Motor / Motor Control Step Fail Phase 2 to 5 Rotor Position Sensor FaultSecondary Source Motor Phase 4 to 5 Bowl Check Fault Phase 4 to 5 Motor Controller Fault Phase 4 Motor Controller Fault Primary Source- Pump Phase 2 to 3 Display / Motor Controller Comms. Error Phase 5 Machine Setup Error Phase 1 to 5 Single Rotor Position Sensor Error Primary Source Wiring Action Phase 1 to 4 Repetitive Current Trip Phase 1 to 5 Repetitive Rotor Position Sensor ErrorPhase 1 to 4 Single Current Trip Phase 4 Single Current Trip & Rotor Position Sensor Error Phase 1 to 5 Motor Stall Phase 1 to 5 Bowl Engaged During Agitate Phase 4 to 5 Brake Function Time-out Fault Complete Disassembly Mechanical Service SectionPhase 5 Topdeck Showing Wiring Connections Phase 2 Topdeck Showing Wiring Connections NB DON’T Remove the Earth Connection from the WrapperPage Page Assembly Guidelines Motor Assembly & Disassembly Assembly Pump Blockage Shaft & Bearing Removal Shaft & Bearing Assembly Page Appendix a Binary Decoding Chart 8 Bits Wash Progress LEDs Fault Finding / Fault Codes Size SettingImportant Note Wiring Connections WM013 Pump Hood KIT January 2000 Phases 2 toPump Hood Kit Part Number 479188P WM51 Diagnostic Flow Chart Sept 1992- Phase 1 only WM70 Premature OUT of Balance February 1995 Phase 2 only WM65 BIB Deflector April 1994- Phase 1 onlyKit Lever Out of Balance & Bracket Phase 2 Part Number WM80 Condensation KIT May 1996 Phase 2 & 3 only WM81 Pump Shield 5KG Smartdrive September 1996 Phases 1 to Appendix C Smarttool Appendix D Tools for Servicing Smartdrive Models Size Width Wash Load Capacity Specifications for IWIW Quick Reference Guide Compact Medium Large Introduction to IW Wash 1 Detergent Activating Wash Front loader type wash Water Temperature Sensing Option Adjustment Mode for IW Pump Other Options Diagnostic Mode for IW Status Display Fault Status Size Setting Mode for IW Recycle