Specifications | Fisher & Paykel 517735 specs

2.0 SPECIFICATIONS

Dimensions

	Compact (5kg)		Medium (6kg)			Large(7kg)
Height to closed Lid	900mm-930mm		900mm-930mm			900mm-930mm
Height to open Lid	1280m-1310mm		1305mm-1335mm			1350mm-1380mm
Width	560mm		600mm			650mm
Depth	560mm		600mm			650mm
Inlet hose length	1100mm		1100mm			1100mm
Dry weight Packed	48Kg		52Kg			58Kg
Dry weight unpacked	43Kg		46Kg			51Kg
Wash Load AS2040	5.0-5.5Kg		6.0-6.5Kg			7.0-7.5Kg
High Water Capacity	63-68L		76-82L			89-94L
Finish
Cabinet		Prepaint (Polyester)
Inner Bowl		Stainless Steel grade 430T
Lid, Console, Outer Bowl, Agitator		Polypropylene
Touch Panel		Polycarbonate
Water fill temp (Default settings)		60oC
Hot		60oC		Cold as per		supply temperature.
Hot / Warm		50oC		Inlet hot water temperature is best
Warm		40oC		at 65oC and		should not exceed
Warm / Cold		35oC		75oC.

Motor. See Section 4.2 for specifications on the stator and rotor.

Pump. See Section 4.7 for specifications.

Water Valves. See Section 4.5 for specifications.

Inlet Water Flow Rate	3 litres per minute minimum.
Standpipe height from floor	Min 850mm Max 1200mm.

Thermistor

Phase 5. NTC-type temperature sensor Resistance 10k ohms @ 25oC. 12.5k ohms @ 20oC In Phase 1-4 this part is not serviceable and mounted within the Motor Controller.

Inner Bowl Speed
Fast Spin	1,000 RPM
Medium Spin	700 RPM
Slow	300 RPM
Stir Speed	25 RPM
Fabric Softener Dosage	75cc
Electric Supply	220/240V AC 50Hz
Max Current	2.8 amps

Acceptable weights for the Inner Bowl

Small (5kg)	10.9-11.5kg
Medium (6kg)	8.9-9.4kg
Compact (7kg)	7.0-7.5kg

CAUTION

ALL TERMINALS AND INTERNAL PARTS SHOULD BE TREATED AS LIVE.

- 3 -

Image 8

Fisher & Paykel 517735 service manual Specifications, ALL Terminals and Internal Parts should be Treated AS Live

Contents

Phase 1 to 5 Smart Drive Electronic Washing Machine Phase 3 GW Phase 4 GWPhase 5 IW Phase 5 Iweco What PHASE, Size & Model is Your SMARTDRIVE? MW, GW Table of Contents Recycle Introduction HOW to Service SmartdriveIf Smartdrive has no Power see Section Smartdrive Servicing Quick Reference Guide Specifications ALL Terminals and Internal Parts should be Treated AS Live Installation InstallationRemoving Transit Restraint Inlet Hoses Installation Environment Water Supply Temperatures SafetyAccessories and Spare Parts Levelling Smartdrive Smartdrive Components Electronics Systems Phase Wiring Diagram Specifications Motor Motor Controller Module Water Level Measurement Pressure Sensor Display Module Water Valves Installation Rotor Position Sensor Pump Motor Specifications Pump Diagram showing the Floating Bowl Inner and Outer Bowls Detection Of Inner Bowl Float Off Point Bowl Check Lid Switch and Out of Balance Switch Lid Switch Water Temperature Sensing Smartdrive Information Favourite cycle GW only All PhasesCustomising Wash Cycles GW only Phase 3 to 5 only Water Saver GW only Phase 3 to 5 only Delay Start GW only Phase 2 to 5 onlyAuto Water Level GW only Phase 3 to 5 only Fabric Softener Dispenser All Phases Amount of Water Used in the Water Saver Rinse Wash Performance Information All Phases Creasing If Smartdrive Powers Off mid cycle Smartdrive ProblemsIf Smartdrive Appears To Have No Power Noisy FloodingLeaking Continuous Spinning or Slow Spinning Poor Wash Performance Siphoning Radio Frequency Interference RFIEarth Leakage It Appears Smartdrive is doing nothing Option Adjustment Mode Wash Water Temperature All Phases Rinse Options All Phases Method of Setting the Wash Temperature End of Cycle Warning Beeps GW Only All Phases Phase Auto Water Fill Level Adjustment GW only Phase Out Of Balance Recovery Adjustment GW and MW only Phase Diagnostic Mode What WAS the Last FAULT? Test LID, OUT of BALANCE, & Size Switches To Test Pump & Water Valves Restart RecycleLOW Water Level LED OFF = Restart OFF Medium Water Level LED on = RE-CYCLE onPage Size Setting Mode Phase 4 and 5 only Insufficient Cold Water Cold Water LED flashing User WarningsInsufficient Hot Water Hot Water LED flashing No Water Both Hot and Cold Water LEDs flashing Overloaded Product High Water LED flashing Restart and Recycle Wash Progress LEDs flashing Phase 4Phase 1 to Demonstration Mode All LEDs flashing in patterns Fault Codes GWC08 GWM08 GWL08 THC08 THM08 THL08GWC09 GWM09 GWL09 IWM09 IWL09 Smartdrive Phases 1 to 5 Fault Descriptions Phase 1 to 5 Motor Controller FaultPhase 1 Communications Fault Primary Source Motor Controller Phase 1 to 5 Display Module Fault Phase 1 to 5 Size ErrorPrimary Source Display Module Action Primary Source Display Module Phase 4 to Phase 1 to 5 Thermistor ErrorAction Phase Phase 2 to Phase 1 to 5 Pressure Sensor Fault Phase 1 to 5 Flood Protection ErrorPhase 1 Pump Fault Primary Source Pressure Tube Phase 1 Pump Connection Fault Phase 5 IW LCD Initialisation Error28 30 xx Phase 1 Display / Motor Controller out of Sequence Primary Source Pump Action Phase 1 MC Reset Error Phase 1 Pump Circuit ErrorPhase 1 Brake Resistor Fault Phase 1 to 5 Water Leak Fault Phase 1 to 5 Pump Block ErrorPrimary Source Pump System Secondary Source Mechanical Action Phase 1 to 5 Tap or Pressure Sensor Tube Fault Phase 1 to 5 Bowl Dis-Engaged FaultPrimary Source Mechanical Primary Source Suds Phase 1 to 5 Temperature Sensor Fault Phase 1 Rotor Fault Primary SourcePhase 1 to 5 OOB Switch Fault Primary Source Mechanical Action Phase 2 to 5 Water in Bowl During Spin Phase 5 Display FaultPrimary Source Pump System Action Secondary Source Motor Controller Phase 2 to 3 Bowl Dis-engaged Fault Phase 2 to 5 Hot and Cold Valve FaultPrimary Source Wiring Phase 2 to 5 Cold Valve Fault Phase 2 to 5 Hot Valve Fault Phase 5 ECO Recirculation FaultPhase 5 ECO Recirculation Fault See fault code Secondary Source Diverter Valve Secondary Source Motor Phase 2 to 5 Rotor Position Sensor FaultPhase 2 to 5 Motor / Motor Control Step Fail Phase 4 to 5 Bowl Check Fault Phase 4 to 5 Motor Controller Fault Phase 4 Motor Controller Fault Primary Source- Pump Phase 2 to 3 Display / Motor Controller Comms. Error Phase 5 Machine Setup Error Phase 1 to 5 Single Rotor Position Sensor Error Primary Source Wiring Action Phase 1 to 5 Repetitive Rotor Position Sensor Error Phase 1 to 4 Single Current TripPhase 1 to 4 Repetitive Current Trip Phase 4 Single Current Trip & Rotor Position Sensor Error Phase 1 to 5 Motor Stall Phase 1 to 5 Bowl Engaged During Agitate Phase 4 to 5 Brake Function Time-out Fault Phase 5 Topdeck Showing Wiring Connections Mechanical Service SectionComplete Disassembly Phase 2 Topdeck Showing Wiring Connections NB DON’T Remove the Earth Connection from the WrapperPage Page Assembly Guidelines Motor Assembly & Disassembly Assembly Pump Blockage Shaft & Bearing Removal Shaft & Bearing Assembly Page Appendix a Binary Decoding Chart 8 Bits Wash Progress LEDs Important Note Size SettingFault Finding / Fault Codes Pump Hood Kit Part Number 479188P WM013 Pump Hood KIT January 2000 Phases 2 toWiring Connections WM51 Diagnostic Flow Chart Sept 1992- Phase 1 only Kit Lever Out of Balance & Bracket Phase 2 Part Number WM65 BIB Deflector April 1994- Phase 1 onlyWM70 Premature OUT of Balance February 1995 Phase 2 only WM80 Condensation KIT May 1996 Phase 2 & 3 only WM81 Pump Shield 5KG Smartdrive September 1996 Phases 1 to Appendix C Smarttool Appendix D Tools for Servicing Smartdrive Specifications for IW IW Quick Reference GuideModels Size Width Wash Load Capacity Compact Medium Large Introduction to IW Wash 1 Detergent Activating Wash Front loader type wash Water Temperature Sensing Option Adjustment Mode for IW Pump Other Options Diagnostic Mode for IW Status Display Fault Status Size Setting Mode for IW Recycle