Furuno FR-2125V specs

4.Connect the GYRO CONVERTER Board to the INT Board (cables supplied with GC-8) as shown below.

INT Board	GYRO CONVERTER Board
J446 (4P)	J7	(5P)
J465 (6P)	J1	(14P)

J446

J465

INT BOARD 03P9252

J5

To gyro

J4

J7

J1

Fix cable to chassis with cable tie.

GYRO CONVERTER

BOARD 64P1106

Figure 4-2 Display unit, inside view

5.Confirm gyrocompass specifications and set the DIP switches and jumper wires on the GYRO CONVERTER Board according to the gyrocompass connected:

•Setting jumper wires and DIP switches by gyrocompass specifications: page 4-4

•Setting jumper wires and DIP switches by make and model of gyrocom- pass: page 4-5

•Location of jumper wires and DIP switches: page 4-6

6.Solder the gyrocompass cable to the VH connector assemblies (supplied).

4-2

Image 43

Furuno FR-2125V installation manual INT Board Gyro Converter Board J446 4P J465 6P 14P

Contents

Installation Manual Marine Radar FR-2125V 00080875300 Safety Instructions Use only the specified power cable System Configuration Name Type Code No Qty Remarks Standard Supply Name Type Code No Remarks Optional Equipment Mounting considerations Antenna Unit Assembling the antenna unit Be sure to remove the guide pins Fastening the radiator to the radiator bracket Fastening the antenna unit to the mounting platform Antenna unit, front view Tabletop mounting Mounting procedureDisplay Unit Before mounting the display unit Stay Setting catch to hole in stay Console type mounting 12 How to dismount the PTU cover Name Type Qty Code No Remarks Display unit modification procedureSeparating the control head Separate type control head kit Type OP03-157, Code No 13 How to dismount covers 14 Clamp position 15 Detaching the control head Plate Control head modification procedure 17 Attaching the handle plate Wiring between display unit and control head 18 How to attach KB fixing plate Wiring Antenna unit, front view, cover removed Correct seating of waterproofing gasket Fabricating signal cable S03-75 Power Switch Power Switch in AC Powered Display Unit DPYCY-3.5 Fabricating the AC power cable supplied CVV-S 8X2C Fabricating the DC power cable CVV-S 8X2C, option Leading cables into the display unit Cable fed from rear of display unit Default method Cables fed from bottom of display unit for console mount Cable fed from outside display unit M4X8 2 pcs Connections Input/Output Signal Connectors on the INT Board JP91 JP92 Changing AC Power SpecificationHow to attach NH connector Power Spec Antenna Restoring default settings Tuning InitializationAccessing Menus for Initialization and Adjustment Adjusting Video Signal Level Picture appears Deviated counterclockwise Heading Alignment Suppressing Main Bang Adjusting Sweep Timing Magnetron heater voltage rating Confirming Magnetron Heater Voltage Press Radar Menu 0 0 0 Initial Setting Menus Initial SETTING2 menu Initial SETTING1 menuInitial SETTING3 menu OWN Ship Information menu Initial SETTING4 menu Gyro Converter GC-8 Installation and connection of the Gyro Converter BoardName Type Qty Code No INT Board Gyro Converter Board J446 4P J465 6P 14P DIP switch, jumper wire settings Connection of external power supplyDefault setting Stator voltage GyrocompassFrequency Remarks Rotor voltage Interval SW2-4 JP1 JP2 JP3 JP4 JP5 SW1 Setting the heading readout on the radar display Name Type Qty Code No ARP Board 18P9002B 008-473-650 Installation of the ARP boardARP board adjustment ARP Board ARP-26 ARP Board 18P9002B Final check Table top/console type RP Board RP-26 Fastening the M-card base assy. to the right arm cover Necessary parts RP-26-Z-2E Code no Separate type control head 13 Display pedestal, front view 14 Display pedestal, front and top views Necessary parts PM-30 and OP03-150 Code no Performance Monitor PM-30 Procedure Alarm KitNecessary parts OP03-156 Code no 16 Display unit, inside view 03P9246A 008-487-440 AC-DC Conversion Kit03P9246C 008-493-700 Board Filter RDP-124 DC 008-492-460 Connection Connection of Rate-of-Turn SignalChecking operation Necessary parts OP03-164 Code no Console Kit 20 How to fasten the edge guard Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page