g
GE
9.4CONNECTION FOR OPTIONS
The installation and cabling of the options must be performed a qualified service person.
9.4.1 Remote Signaling Box (RSB)
The optional Remote Signaling Box allows monitoring of the operation of the UPS, using the potential free contacts fitted on the “P4 - Customer Interface Board“ of the UPS.
It can be used by simply putting the box on a desktop or on a wall or, removing the box, it can be surface mounted.
The remote panel contains an internal buzzer and the following status indicators:
•Mimic diagram with LED's indicating the operation of Rectifier and Inverter, and the power source supplying the critical Load.
• | Alarm | (LED light and audible alarm) indicating a critical situation on the UPS. |
• | Stop | indicating the UPS is preparing to shut down in a short time. |
• | Mute | push button to reset the buzzer. |
• | Test | push button checks all the LED’s and the buzzer of the remote panel. |
The cable connecting the RSB to the UPS cabinet must be min. 16 wires / 0.25mm2.
The plug B is included in the delivery of the option RSB (cable connecting UPS with RSB not included). Maximal admitted length: 985 ft (300 m).
It must be wired at one end with a D - female plug- 25 pin (J2 – P4 Customer Interface Board).
The alarms on free potential contacts can be connected on terminals X1 instead J2 (see correlation X1 – J2 in chapter 8.1).
XA |
|
| pink |
|
|
| A |
|
| red |
|
| REMOTE | ||
TERMINALS | grey |
|
| SIGNALLING | |||
blue |
|
| |||||
BLOCK |
|
|
| BOX | |||
|
|
|
| ||||
|
|
|
|
|
| ||
|
|
|
|
| red pink |
| IM6544 |
| 25 |
|
| blue grey | 24V | 1 | |
|
|
| X15 | ||||
|
|
| GND | ||||
| 24 |
|
|
| 2 | ||
| 23 |
|
|
| UTILITY FAILURE | 31 |
|
| 22 |
|
|
| 32 |
| |
| white |
|
|
|
| ||
| 21 |
|
|
| 33 |
| |
MALE | 20 | brown |
|
|
| 34 |
|
19 | green |
|
|
| 37 |
| |
18 | yellow |
|
|
| 38 |
| |
- | 17 |
|
|
|
| 40 |
|
D | 16 |
|
|
|
|
| |
black |
|
|
| 42 | X4 | ||
- SUB | 15 | violet |
|
| LOAD ON INVERTER | 43 | |
14 |
|
|
| 44 |
| ||
13 |
|
|
|
|
| ||
J2 | 12 |
|
|
| LOAD ON MAINS | 49 |
|
11 |
|
|
| 50 |
| ||
- |
|
|
|
|
| ||
10 |
|
|
|
| 55 |
| |
| 9 |
|
|
|
| 56 |
|
12 | 1 |
13 | 2 |
14 | 3 |
15 | 4 |
16 | 5 |
17 | 6 |
18 | 7 |
19 | 8 |
20 | 9 |
21 | 10 |
22 | 11 |
1 |
|
2 |
|
J2
14 | 1 |
9
1
P4 - IM0005 
Customer Interface
|
| Pink + Red |
XA | 1 | XA |
2 | ||
|
| TERMINALS BLOCK |
|
| Grey + Blue |
1 |
| J2 |
2 |
| |
3 |
| B PLUG |
4 |
| SUB D - MALE |
|
| |
1 |
| / 300m |
| 985ft | |
2 |
| |
3 |
| max |
4 |
|
|
A
B | 8 | grey/pink |
|
|
|
| blue/red |
|
|
| |
| 7 |
|
|
| |
|
|
|
|
| |
| 6 | white/green |
| 16 |
|
| 5 | COMMON ALLARM |
| ||
| brown/green | 17 |
| ||
| 4 |
|
| ||
| white/yellow |
| 19 | X3 | |
| 3 | AUX. BUZZER | |||
| yellow/brown | 20 | |||
| 2 |
| STOP OPERATION | 22 |
|
| 1 |
|
| ||
|
| 23 |
| ||
|
|
|
|
|
P.S.: The above mentioned colors are suitables only for XY standard cable
|
|
| S |
| in |
| U |
| m | 1 | |
| 3 | _ | |
| 7m | 0 | |
| S | ||
| 7 |
| M |
|
|
| R |
|
|
| _ |
|
|
| 0 |
|
|
| 5 |
|
|
| 1 |
|
|
| - |
|
|
| 0 |
| Stop |
| 1 |
1/4"5 in 130mm |
| 0 | |
|
| _ | |
| 0 | ||
| Alarm |
| T |
|
| P | |
|
|
| O |
|
|
| _ |
|
|
| 0 |
|
| 0 | |
|
| 5 | |
|
| T | |
g | Mute Test | G | |
S | |||
| GE Digital Energy |
|
|
8 1/2" in 216mm
Fig.
ATerminals X3, X4 and X15 fitted inside the Remote Signaling Box.
BPlug J2 (sub D - male - 25 pin) must be connected to the connector J2 (sub D - female- 25 pin) located on “P4 - Customer Interface Board“.
XA Terminals block XA for 24 VDC / 1A supply Remote Signaling Box.
If the remote signal panel is plugged on connector J2, the terminal blocks X1 cannot be used to drive an external alarms monitoring device, because it is supplied by the internal UPS low voltage power supply.
OPM_SGS_USM_10K_40K_0US_V010.doc | 84/88 | Operating Manual SG Series 10, 20, 30 & 40 kVA |