Hitachi CP-X200 instruction manual Appendix

B－36

B36

The following table lists the holding registers for the “C” Group Intelligent Input Functions.

List of Holding Registers

	Func.	Name	R/W		Description	Network Data
	Code					Reg.	Range	Res.
	C001	Terminal [1] function	R/W			1103h	0, 1, 2, 3,	
	C201	Terminal [1] function,	R/W			1532h	4, 5, 6, 7,
		2nd motor					8, 9, 11,
	C002	Terminal [2] function	R/W			1104h	12, 13,
	C202	Terminal [2] function,	R/W			1533h	15, 16,
							18, 19,
		2nd motor
							20, 21,	Appendix
	C003	Terminal [3] function	R/W			1105h
				See “Input Terminal Configuration”			22, 23,
	C203	Terminal [3] function,	R/W			1534h
					on page 3-49		24, 27,
B	C004	2nd motor	R/W			1106h	28, 29,
Appendix		Terminal [4] function					31, 50,	B
	C204	Terminal [4] function,	R/W			1535h	51, 52,
		2nd motor					53, 64,
	C005	Terminal [5] function	R/W			1107h	255
	C205	Terminal [5] function,	R/W			1536h
		2nd motor
	C011	Terminal [1] active state	R/W	Select logic conversion, two option		110Bh	0, 1	
	C012	Terminal [2] active state	R/W	codes:		110Ch	0, 1	
	C013	Terminal [3] active state	R/W	00	normally open [NO]	110Dh	0, 1	
	C014	Terminal [4] active state	R/W	01	normally closed [NC]	110Eh	0, 1	
	C015	Terminal [5] active state	R/W			110Fh	0, 1	
	C021	Terminal [11] function	R/W			1114h	0, 1, 2, 3,	
	C026	Alarm relay terminal	R/W		See “Output Terminal	1119h	4, 5, 6, 7,
					Configuration” on page 3-54		8, 9, 10,	
		function					43

C028 [AM] signal selection R/W Two available functions: 111Bh 0, 1 

00motor speed

01motor current

C031	Terminal [11] active	R/W	Select logic conversion:		111Dh	0, 1	
	state		00	normally open [NO]
			01	normally closed [NC]
C036	Alarm relay active state	R/W	Select logic conversion:		1122h	0, 1	

00normally open [NO]

01normally closed [NC]

C038 Output mode of low load	R/W Three option codes:	1178h 0, 1, 2	
detection signal	00 Disabled

01During acceleration, deceleration and constant speed

			02 During constant speed only
C039	Low load detection level	R/W	Set the level of low load detection,	1179h	0 to	0.01%
			range is 0.0 to 2.0*rated current		20000
C041	Overload level setting	R/W	Sets the overload signal level	1124h	0 to	0.01%
			between 0% and 200% (from 0 to two		20000
			time the rated current of the
C241	Overload level setting,	R/W		153Ah
	2nd motor		inverter)
C042	Frequency arrival	R/W	Sets the frequency arrival setting	1126h	0 to 4000	0.1 Hz
	setting for acceleration		threshold for the output frequency		*1
			during acceleration,
			range is 0.0 to 400.0 Hz
C043	Frequency arrival	R/W	Sets the frequency arrival setting	1128h	0 to 4000	0.1 Hz
	setting for deceleration		threshold for the output frequency
			during deceleration,
			range is 0.0 to 400.0 Hz