Hitachi CP-X200 －10, 10, General Specifications, Following table applies to all X200 inverters

1－10

110

started	Getting started
Getting

General Specifications

The following table applies to all X200 inverters.

	Item		General Specifications
Protective housing *1			IP00
Control method			Sinusoidal Pulse Width Modulation (PWM) control
Carrier frequency			2kHz to 12kHz (default setting: 3kHz)
Output frequency range *4			0.5 to 400Hz
Frequency accuracy			Digital command: 0.01% of the maximum frequency
			Analog command: 0.4% of the maximum frequency (25θC ρ 10θC)
Frequency setting resolution			Digital: 0.1Hz; Analog: max. frequency/1000
Volt./Freq. characteristic			V/f control (constant torque, reduced torque)
Overload capacity			150% rated current for 1 minute
Acceleration/deceleration time			0.01 to 3000 seconds, linear and S-curve accel/decel, second
			accel/decel setting available
Input	Freq.	Operator panel	Up and Down keys / Value settings
signal	setting	Potentiometer	Analog setting
		External signal	0 to 10 VDC (input impedance 10k Ohms), 4 to 20mA (input
		*9	impedance 250 Ohms), Potentiometer (1k to 2k Ohms, 2W)
	FWD/	Operator panel	Run/Stop (Forward/Reverse run change by command)
	REV run	External signal	Forward run/stop, Reverse run/stop
	Intelligent input		FW (forward run command), RV (reverse run command), CF1~CF4
	terminal		(multi-stage speed setting), JG (jog command), DB (external
			braking), SET (set second motor), 2CH (2-stage accel./decel.
			command), FRS (free run stop command), EXT (external trip), USP
			(startup function), SFT (soft lock), AT (analog current input select
			signal), RS (reset), PTC (thermistor thermal protection), STA (start),
			STP (stop), F/R (forward/reverse), PID (PID disable), PIDC (PID
			reset), UP (remote control up function), DWN (remote control down
			function), UDC (remote control data clearing), OPE (operator
			control), ADD (add frequency enable), F-TM (force terminal mode),
			RDY (Run ready), SP-SET (Special set) , EMR (Emergency Stop)
Output	Intelligent output		RUN (run status signal), FA1,FA2 (frequency arrival signal),
signal	terminal		OL (overload advance notice signal), OD (PID error deviation
			signal), AL (alarm signal), Dc (analog input disconnect detect),
			FBV (PID two-stage control output), NDc (network detection signal),
			LOG (Logic output), ODc (comm. watchdog error), LOC (Low load)
	Frequency monitor		Analog output; Select output frequency or output current monitor
Alarm output contact			ON for inverter alarm (1c contacts, both normally open or closed
			avail.)
Other functions			AVR function, curved accel/decal profile, upper and lower limiters,
			16-stage speed profile, fine adjustment of start frequency, carrier
			frequency change (2 to 12kHz) *10, frequency jump, gain and bias
			setting, process jogging, electronic thermal level adjustment, retry
			func., trip history monitor, 2nd setting select, fan ON/OFF selection.
Protective function			Over-current, over-voltage, under-voltage, overload, extreme high
			temperature, CPU error, memory error, ground fault detection at
Operating		Temperature	startup, electronic thermal
			Operating (ambient): -10 to 40θC(*10), / Storage: -25 to 70θC(*11)
environment		Humidity	20 to 90% humidity (non-condensing)
		Vibration *12	5.9m/s2 (0.6G), 10 to 55 Hz
		Location	Altitude 1,000m or less, indoors (no corrosive gasses or dust)
Coating color			Blue
Options			Remote operator unit, copy unit, cables for the units, braking unit,
			braking resistor, AC reactor, DC reactor, noise filter