Presentation | Husqvarna PT26 D instruction

Presentation

Chapter 4: Presentation

Congratulations on your choice of an exceptionally high quality product. This operator's manual describes Husqvarna PT 26D.

It is ﬁtted with a Perkins 3 cylinder diesel engine developing 26 horse power.

PT 26D is equipped with hydraulic steering and attachment lift. They are supplied with pressure from a pump on the engine.

The machine is all wheel drive in low speed mode.

The power transmission from the engine is hydrostatic. It is supplied with pressure by a pump under the driver’s seat. A shaft with two ﬂexible couplings powers the pump. Flow and direction are regulated with the pedals, so that forward and reversing speeds are variably controlled. One pedal to drive forwards (1) and one pedal to reverse (2). The pump drives four hydraulic motors in parallel, one for each wheel.

The power transmission is also used as service brake.

There are low and high speeds for driving. High or low speed is selected using a switch.

The machine is equipped with an electro-hydraulic differential lock, which is controlled by a pedal. The differential lock only works longitudinally, which means that you can turn the machine with the differential lock activated.

The differential lock does not work in high speed.

Rear light, horn, direction indicators and rotating warning lights are optional equipment (trafﬁc kit).

The cutting unit takes power from the engine by means of an electromagnetic clutch, two V-belts, apower take- off shaft, a propeller shaft and a bevel gear.

PT 26D

Speed control

Differential lock pedal

15

Image 16

Husqvarna PT26 D manual Presentation

Contents

PT26 D Contents Page Introduction CongratulationsDriving and Transport on Public Roads Towing Proper Service Serial Number Symbols and Decals Important Information Safety Instructions General Use When driving Driving on slopes Do as follows Maintenance Children Avoid sparking and its consequences by Other protective devices are not ﬁtted or are defective Transport Environment protection User responsibility Presentation Placement of controls Speed control Parking brake Control panel Seat Adjusting the cutting height Steering wheel and steering wheel consoleDifferential Lock Fuelling Controls on the control panel Control lever hydraulicsWinter fuel and parafﬁn precipitation Lifting the cutting unit transport position Switch for operation of cutting unit Switch for extra hydraulic function hydraulic kit optionIndicators trafﬁc kit option Push button for horn trafﬁc kit option Starter switch HeadlightThrottle control High speed Weight transfer Spare Power outletRotating warning light trafﬁc kit option Parking lights trafﬁc kit option Chronometer Adjusting the steering wheel settingLever for steering wheel console angle Rops Cooling system Cutting unit Antifreeze Accessories Driving Mowing Tips Before Starting Start gas or ether must not be used for this engine Starting the engine Starting with a weak battery Starting in cold conditions Driving the machine Braking Cutting the engineBleeding in the event of fuel stoppage Engine stop Maintenance Schedule Maintenance250 500 1000 2000 250 500 1000 2000 Cleaning Cleaning the radiators heat exchanger Adjusting the pump and generator drive beltsRemoving the machine’s covers Checking radiatorgrilles Checking and adjusting the throttle control Adjusting the parking brakeReplacing the pump and generator drive belts Checking the exhaust system Cleaning the cyclone ﬁlter Servicing the air ﬁlterReplacing the air ﬁlter Emptying the particle trap Servicing the fuel ﬁlter Bleeding the fuel systemChecking the Tyre Pressures Servicing the battery Fuses Checking the Safety System FU2 FU9 Replacing the bulb in the headlight Light setting Cutting Unit ComponentsAttaching and removing the cutting unit Side shifting the cutting unit Important Information Setting the cutting height and tilt angle Cutting height Cutting Unit’s Service Position Placing in the Service PositionTilt angle Ground pressure Releasing the Service Position Cutting Unit Model Checking the Blades Replacing the power take-off beltsAlways replace the belts in pairs Replacing the cutting unit belt Adjusting the power take-off beltsReplacing the belt on the Combi unit Removal of BioClip Plug Lubrication Lubrication ScheduleGeneral Lubricating the cables Handle for cutting height setting Lubricating in Accordance with Lubrication SchedulePivot wheel bearings Cutting unit’s bevel gear Power take-off shaft’s front support bearing Lift cylinderEngine Oil Viscosity and quality Filling engine oil Changing the Engine Oil Replacing the engine’s oil ﬁlter Hydraulic oilInspection off the oil level Filling hydraulic oil Hydraulic oil ﬁlter, change Cutting unit mountingLifting arm’s rear bearings Driver’s Seat Parking brake cables Control cylinder Lubrication Trouble Shooting Guide Problem Cause Problem Cause Problem Cause Trouble Shooting Guide Storage Winter Storage Service Electrical system Hydraulic System Hydraulic System Fuel system Technical Data Data PT 26D Transmission Vibration levels4 Technical Data EU Declaration of Conformity only applies to Europe Design standardsDiverse design standards Design standards Page Page 1153893-26 ´z+Uy@¶6u¨ ´z+Uy@¶6u¨ Original instructions