Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna PT26 D manual Parking brake cables, Control cylinder, Lubrication

Models: PT26 D

1 80

Download 80 pages 52.58 Kb

Page 60

Image 60

Lubrication

12. Parking brake cables

See “Lubricating the cables” on page 53.

Lubricate the upper ends of the cable.

Remove the cable’s rubber casing (R and L) when lubricating.

Lubricate the cable with an oil can, apply the parking brake a few times and lubricate again.

Parking brake cables

13. Control cylinder

2 nipples, one at each end of the cylinder, lubricate using a grease gun until grease is forced out.

Control cylinder

Page 60

Image 60

Husqvarna PT26 D manual Parking brake cables, Control cylinder, Lubrication

Contents

PT26 D Operator′s manualEnglish Contents Page Chapter 1 Introduction CongratulationsDriving and Transport on Public Roads TowingProper Service Serial NumberIntroduction Chapter 2 Symbols and Decals Symbols and DecalsIMPORTANT INFORMATION Xxx xxx xxxx xxxxxxxxx xxx xxxxx xxx xxxxxxxxx xx xxxxx. Xxx xxxxxxxx xx x x xxxxxxx xx xxxx Symbols and DecalsChapter 3 Safety Instructions Safety InstructionsGeneral Use Safety Instructions foreign objects Never drive close to objects or other machinesDriving on slopes Do as followsSafety Instructions Maintenance ChildrenSafety Instructions actions in the engine room Avoid sparking and its consequences bySafety Instructions IMPORTANT INFORMATIONSafety Instructions ﬂammable liquids are stored in an open containerTransport Environment protectionSafety Instructions IMPORTANT INFORMATIONUser responsibility Safety InstructionsChapter 4 Presentation PresentationPlacement of controls Switch for weight transfer pageSwitch for operating the cutting unit page Switch for 2nd hydraulic function option page1-2. Speed control 3. Parking brakeWarning lamp Battery charging page Warning lamp Right-hand indicator pageDo not adjust the seat whilst driving. Risk of unsafe operation 4. Control panel5-9. Seat Presentation12. Adjusting the cutting height 10. Steering wheel and steering wheel console11. Differential Lock 13. Fuelling21-37. Controls on the control panel 21. Control lever hydraulicsWinter fuel and parafﬁn precipitation Lifting the cutting unit transport position22. Switch for operation of cutting unit 23. Switch for extra hydraulic function hydraulic kit option25. Indicators trafﬁc kit option 24. Push button for horn trafﬁc kit option26. Starter switch 27. Headlight28. Throttle control 29. High speed30. Weight transfer 33. Spare 34-35.Power outlet31. Rotating warning light trafﬁc kit option 32. Parking lights trafﬁc kit optionAdjusting the steering wheel setting 36. Chronometer40-51. Warning lamps 49. Lever for steering wheel console angleRops The bow is foldable. Pull out the pins and fold the bow backwardsIf the bow is used unfolded, safety belt must be used If the bow is used folded, safety belt should NOT be usedCooling system IMPORTANT INFORMATIONPresentation Cutting unit AntifreezeIMPORTANT INFORMATION IMPORTANT INFORMATIONAccessories TowingPresentation laterally to the side in relation to the machineChapter 5 Driving Mowing TipsDriving Use ear protectionBefore Starting Start gas or ether must not be used for this engineIMPORTANT INFORMATION IMPORTANT INFORMATIONStarting the engine Do not run the starter motor for more thanIMPORTANT INFORMATION DrivingStarting with a weak battery Starting in cold conditionsIMPORTANT INFORMATION DrivingDriving the machine DrivingBraking Cutting the engineBleeding in the event of fuel stoppage Engine stopChapter 6 Maintenance Maintenance ScheduleMaintenance 1000Maintenance 10002000 Cleaning Avoid using a high pressure washer or a steam cleanerLubricate the machine if necessary after cleaning The engine is stopped The parking brake is onCleaning the radiators heat exchanger Adjusting the pump and generator drive belts1. Slacken off the adjustment screw 1/2 turn Removing the machine’s coversChecking and adjusting the throttle control Adjusting the parking brakeA poorly adjusted parking brake can result in reduced braking ability Replacing the pump and generator drive beltsCleaning the cyclone ﬁlter Servicing the air ﬁlterReplacing the air ﬁlter Emptying the particle trapBleeding the fuel system Servicing the fuel ﬁlterChecking the Tyre Pressures MaintenanceServicing the battery What to do in case of contact with battery acidFuses External Rinse thoroughly with waterChecking the Safety System Replacing the bulb in the headlight MaintenanceIMPORTANT INFORMATION Light setting The Cutting Unit ComponentsAttaching and removing the cutting unit Side shifting the cutting unitMaintenance 4. Stop the engine 5. Remove the pins on both sidesIMPORTANT INFORMATION Setting the cutting height and tilt angle Cutting heightMaintenance IMPORTANT INFORMATIONThe Cutting Unit’s Service Position Placing in the Service PositionTilt angle Ground pressureReleasing the Service Position Cutting Unit ModelMaintenance Replacing the power take-off belts Checking the BladesAlways replace the belts in pairs MaintenanceAdjusting the power take-off belts Replacing the cutting unit beltReplacing the belt on the Combi unit MaintenanceRemoval of BioClip Plug MaintenanceChapter 7 Lubrication Lubrication ScheduleGeneral Lubricating the cables2. Handle for cutting height setting Lubricating in Accordance with the1. Pivot wheel bearings 3. Cutting unit’s bevel gear6. The power take-off shaft’s front support bearing 5. Lift cylinder7. Engine Oil Viscosity and qualityFilling engine oil Changing the Engine OilAvoid skin contact wash with soap and water in case of spills 1. Position the wheels fully to the left7. Replacing the engine’s oil ﬁlter 8. Hydraulic oilInspection off the oil level Filling hydraulic oil8. Hydraulic oil ﬁlter, change 9. Cutting unit mounting10. Lifting arm’s rear bearings 11. Driver’s Seat12. Parking brake cables 13. Control cylinderLubrication Lubrication Chapter 8 Trouble Shooting Guide Trouble Shooting GuideProblem CauseTrouble Shooting Guide ProblemCause Trouble Shooting Guide ProblemCause Uneven mowing resultsTrouble Shooting Guide Chapter 9 Storage Winter StorageStorage Service StorageChapter 10 Electrical system Electrical systemElectrical system, component locations Chapter 11 Hydraulic System Hydraulic SystemKeep the hydraulic system clean. Remember to Hydraulic SystemChapter 12 Fuel system Fuel systemTechnical Data Technical DataData PT 26DTechnical Data DataPT 26D Technical Data IMPORTANT INFORMATIONIMPORTANT INFORMATION DataTechnical Data Design standards Design standardsEU Declaration of Conformity only applies to Europe Diverse design standardsDesign standards Page Page 1153893-26 ´z+Uy@¶6u¨ ´z+Uy@¶6u¨ Original instructions