1153893-26 ´z+Uy@¶6u¨ ´z+Uy@¶6u¨ | Husqvarna PT26 D manual

Original instructions

1153893-26

´®z+Uy@¶6u¨ ´®z+Uy@¶6u¨ 2010-08-16

Image 80

Husqvarna PT26 D manual 1153893-26 ´z+Uy@¶6u¨ ´z+Uy@¶6u¨, Original instructions

Contents

PT26 D Contents Page Introduction CongratulationsDriving and Transport on Public Roads Towing Proper Service Serial Number Symbols and Decals Important Information Safety Instructions General Use When driving Driving on slopes Do as follows Maintenance Children Avoid sparking and its consequences by Other protective devices are not ﬁtted or are defective Transport Environment protection User responsibility Presentation Placement of controls Speed control Parking brake Control panel Seat Adjusting the cutting height Steering wheel and steering wheel consoleDifferential Lock Fuelling Controls on the control panel Control lever hydraulicsWinter fuel and parafﬁn precipitation Lifting the cutting unit transport position Switch for operation of cutting unit Switch for extra hydraulic function hydraulic kit optionIndicators trafﬁc kit option Push button for horn trafﬁc kit option Starter switch HeadlightThrottle control High speed Weight transfer Spare Power outletRotating warning light trafﬁc kit option Parking lights trafﬁc kit option Lever for steering wheel console angle Adjusting the steering wheel settingChronometer Rops Cooling system Cutting unit Antifreeze Accessories Driving Mowing Tips Before Starting Start gas or ether must not be used for this engine Starting the engine Starting with a weak battery Starting in cold conditions Driving the machine Braking Cutting the engineBleeding in the event of fuel stoppage Engine stop 250 500 1000 2000 MaintenanceMaintenance Schedule 250 500 1000 2000 Cleaning Cleaning the radiators heat exchanger Adjusting the pump and generator drive beltsRemoving the machine’s covers Checking radiatorgrilles Checking and adjusting the throttle control Adjusting the parking brakeReplacing the pump and generator drive belts Checking the exhaust system Cleaning the cyclone ﬁlter Servicing the air ﬁlterReplacing the air ﬁlter Emptying the particle trap Checking the Tyre Pressures Bleeding the fuel systemServicing the fuel ﬁlter Servicing the battery Fuses Checking the Safety System FU2 FU9 Replacing the bulb in the headlight Light setting Cutting Unit ComponentsAttaching and removing the cutting unit Side shifting the cutting unit Important Information Setting the cutting height and tilt angle Cutting height Cutting Unit’s Service Position Placing in the Service PositionTilt angle Ground pressure Releasing the Service Position Cutting Unit Model Always replace the belts in pairs Replacing the power take-off beltsChecking the Blades Replacing the belt on the Combi unit Adjusting the power take-off beltsReplacing the cutting unit belt Removal of BioClip Plug Lubrication Lubrication ScheduleGeneral Lubricating the cables Handle for cutting height setting Lubricating in Accordance with Lubrication SchedulePivot wheel bearings Cutting unit’s bevel gear Power take-off shaft’s front support bearing Lift cylinderEngine Oil Viscosity and quality Filling engine oil Changing the Engine Oil Replacing the engine’s oil ﬁlter Hydraulic oilInspection off the oil level Filling hydraulic oil Hydraulic oil ﬁlter, change Cutting unit mountingLifting arm’s rear bearings Driver’s Seat Parking brake cables Control cylinder Lubrication Trouble Shooting Guide Problem Cause Problem Cause Problem Cause Trouble Shooting Guide Storage Winter Storage Service Electrical system Hydraulic System Hydraulic System Fuel system Technical Data Data PT 26D Transmission Vibration levels4 Technical Data Diverse design standards Design standardsEU Declaration of Conformity only applies to Europe Design standards Page Page 1153893-26 ´z+Uy@¶6u¨ ´z+Uy@¶6u¨ Original instructions