Design standards, Diverse design standards | Husqvarna PT26 D

Design standards

Design standards

EU Declaration of Conformity (only applies to Europe)

Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare under sole responsibility that the Husqvarna PT 26D, from 2010’s serial numbers and onwards (the year is clearly stated in plain text on the rating plate with subsequent serial number), conforms with the requirements of the COUNCIL’S DIRECTIVE:

-of May 17, 2006 <Helv>"relating to machinery<Helv>" 2006/42/EC

-of December 15, 2004 ”relating to electromagnetic compatibility” 2004/108/EG.

-of May 8, 2000 “relating to noise emissions into the surroundings” 2000/14/EC.

Information regarding noise emissions and the cutting width, see “Technical Data”.

The following harmonised standards have been applied: EN121002-2, EN836.

Registered body 0404, SMP Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden has issued reports with numbers:

01/901/ 079, 01/901/080 regarding the assessment of conformity according to annex VI to the COUNCIL’S DIRECTIVE of May 8, 2000 “relating to the emission of noise to surroundings” 2000/14/EC.

Huskvarna December 29, 2009

Claes Losdahl, Development Manager/Garden Products (Authorized representative for Husqvarna AB and responsible for technical documentation.)

Diverse design standards

The electrical system is designed to conform to requirements of insurance companies regarding the risk of ﬁre. The electrical system has an electrical main circuit breaker and max. 10 A in the control circuit. All electrical cables are protected by a protective hose. The electrical system must not be modiﬁed as this can disregard the requirements of the insurance companies.

The electrical system is designed to satisfy the requirements made by insurance companies on machines with a price exceeding 2 base amounts.

75

Image 76

Husqvarna PT26 D manual Design standards, EU Declaration of Conformity only applies to Europe, Diverse design standards

Contents

PT26 D Contents Page Introduction CongratulationsDriving and Transport on Public Roads Towing Proper Service Serial Number Symbols and Decals Important Information Safety Instructions General Use When driving Driving on slopes Do as follows Maintenance Children Avoid sparking and its consequences by Other protective devices are not ﬁtted or are defective Transport Environment protection User responsibility Presentation Placement of controls Speed control Parking brake Control panel Seat Adjusting the cutting height Steering wheel and steering wheel consoleDifferential Lock Fuelling Controls on the control panel Control lever hydraulicsWinter fuel and parafﬁn precipitation Lifting the cutting unit transport position Switch for operation of cutting unit Switch for extra hydraulic function hydraulic kit optionIndicators trafﬁc kit option Push button for horn trafﬁc kit option Starter switch HeadlightThrottle control High speed Weight transfer Spare Power outletRotating warning light trafﬁc kit option Parking lights trafﬁc kit option Chronometer Adjusting the steering wheel settingLever for steering wheel console angle Rops Cooling system Cutting unit Antifreeze Accessories Driving Mowing Tips Before Starting Start gas or ether must not be used for this engine Starting the engine Starting with a weak battery Starting in cold conditions Driving the machine Braking Cutting the engineBleeding in the event of fuel stoppage Engine stop Maintenance Schedule Maintenance250 500 1000 2000 250 500 1000 2000 Cleaning Cleaning the radiators heat exchanger Adjusting the pump and generator drive beltsRemoving the machine’s covers Checking radiatorgrilles Checking and adjusting the throttle control Adjusting the parking brakeReplacing the pump and generator drive belts Checking the exhaust system Cleaning the cyclone ﬁlter Servicing the air ﬁlterReplacing the air ﬁlter Emptying the particle trap Servicing the fuel ﬁlter Bleeding the fuel systemChecking the Tyre Pressures Servicing the battery Fuses Checking the Safety System FU2 FU9 Replacing the bulb in the headlight Light setting Cutting Unit ComponentsAttaching and removing the cutting unit Side shifting the cutting unit Important Information Setting the cutting height and tilt angle Cutting height Cutting Unit’s Service Position Placing in the Service PositionTilt angle Ground pressure Releasing the Service Position Cutting Unit Model Checking the Blades Replacing the power take-off beltsAlways replace the belts in pairs Replacing the cutting unit belt Adjusting the power take-off beltsReplacing the belt on the Combi unit Removal of BioClip Plug Lubrication Lubrication ScheduleGeneral Lubricating the cables Handle for cutting height setting Lubricating in Accordance with Lubrication SchedulePivot wheel bearings Cutting unit’s bevel gear Power take-off shaft’s front support bearing Lift cylinderEngine Oil Viscosity and quality Filling engine oil Changing the Engine Oil Replacing the engine’s oil ﬁlter Hydraulic oilInspection off the oil level Filling hydraulic oil Hydraulic oil ﬁlter, change Cutting unit mountingLifting arm’s rear bearings Driver’s Seat Parking brake cables Control cylinder Lubrication Trouble Shooting Guide Problem Cause Problem Cause Problem Cause Trouble Shooting Guide Storage Winter Storage Service Electrical system Hydraulic System Hydraulic System Fuel system Technical Data Data PT 26D Transmission Vibration levels4 Technical Data EU Declaration of Conformity only applies to Europe Design standardsDiverse design standards Design standards Page Page 1153893-26 ´z+Uy@¶6u¨ ´z+Uy@¶6u¨ Original instructions