Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna PT26 D manual Speed control, Parking brake, Presentation, Steering wheel console

Models: PT26 D

1 80

Page 18

Presentation

	Steering wheel console
40.	Warning lamp Battery charging page 24	47.	Warning lamp High speed page 24
41.	Warning lamp Differential lock page 24	48.	Warning lamp Right-hand indicator page 24
42.	Warning lamp Coolant temperature page 24	49.	Lever for tilting the steering wheel console page 24
43.	Warning lamp Glow plug heating page 24	50.	Warning lamp Full beam page 24
44.	Warning lamp Engine oil pressure page 24	51.	Warning lamp Left-hand indicator page 24

45.Warning lamp Cutting unit operation page 24

46.Warning lamp Parking brake page 24

1-2. Speed control

The speed of the machine is variably controlled using two pedals. Pedal (1) is used to travel forwards and pedal (2) to reverse.

WARNING:

Make sure that no branches can interfere with the pedals when mowing under bushes.

Speed control

3. Parking brake

Apply the parking brake by moving the handle forward.

Release the parking brake by moving the handle back.

Parking brake

Page 18

Image 18

Husqvarna PT26 D Speed control, Parking brake, Presentation, Steering wheel console, Warning lamp Battery charging page

Contents

PT26 D Operator′s manualEnglish Contents Page Driving and Transport on Public Roads Chapter 1 IntroductionCongratulations TowingProper Service Serial NumberIntroduction Chapter 2 Symbols and Decals Symbols and Decalsxxxxx xx xxxxx. Xxx xxxxxxxx xx x x xxxxxxx xx xxxx IMPORTANT INFORMATIONXxx xxx xxxx xxxxxxxxx xxx xxxxx xxx xxxx Symbols and DecalsChapter 3 Safety Instructions Safety InstructionsGeneral Use Safety Instructions foreign objects Never drive close to objects or other machinesDriving on slopes Do as followsSafety Instructions Maintenance ChildrenSafety Instructions Safety Instructions actions in the engine roomAvoid sparking and its consequences by IMPORTANT INFORMATIONSafety Instructions ﬂammable liquids are stored in an open containerSafety Instructions TransportEnvironment protection IMPORTANT INFORMATIONUser responsibility Safety InstructionsChapter 4 Presentation PresentationSwitch for operating the cutting unit page Placement of controlsSwitch for weight transfer page Switch for 2nd hydraulic function option pageWarning lamp Battery charging page 1-2. Speed control3. Parking brake Warning lamp Right-hand indicator page5-9. Seat Do not adjust the seat whilst driving. Risk of unsafe operation4. Control panel Presentation11. Differential Lock 12. Adjusting the cutting height10. Steering wheel and steering wheel console 13. FuellingWinter fuel and parafﬁn precipitation 21-37. Controls on the control panel21. Control lever hydraulics Lifting the cutting unit transport position25. Indicators trafﬁc kit option 22. Switch for operation of cutting unit23. Switch for extra hydraulic function hydraulic kit option 24. Push button for horn trafﬁc kit option28. Throttle control 26. Starter switch27. Headlight 29. High speed31. Rotating warning light trafﬁc kit option 30. Weight transfer33. Spare 34-35.Power outlet 32. Parking lights trafﬁc kit option40-51. Warning lamps Adjusting the steering wheel setting36. Chronometer 49. Lever for steering wheel console angleIf the bow is used unfolded, safety belt must be used RopsThe bow is foldable. Pull out the pins and fold the bow backwards If the bow is used folded, safety belt should NOT be usedCooling system IMPORTANT INFORMATIONPresentation IMPORTANT INFORMATION Cutting unitAntifreeze IMPORTANT INFORMATIONPresentation AccessoriesTowing laterally to the side in relation to the machineDriving Chapter 5 DrivingMowing Tips Use ear protectionIMPORTANT INFORMATION Before StartingStart gas or ether must not be used for this engine IMPORTANT INFORMATIONIMPORTANT INFORMATION Starting the engineDo not run the starter motor for more than DrivingIMPORTANT INFORMATION Starting with a weak batteryStarting in cold conditions DrivingDriving the machine DrivingBleeding in the event of fuel stoppage BrakingCutting the engine Engine stopMaintenance Chapter 6 MaintenanceMaintenance Schedule 1000Maintenance 10002000 Lubricate the machine if necessary after cleaning CleaningAvoid using a high pressure washer or a steam cleaner The engine is stopped The parking brake is on1. Slacken off the adjustment screw 1/2 turn Cleaning the radiators heat exchangerAdjusting the pump and generator drive belts Removing the machine’s coversA poorly adjusted parking brake can result in reduced braking ability Checking and adjusting the throttle controlAdjusting the parking brake Replacing the pump and generator drive beltsReplacing the air ﬁlter Cleaning the cyclone ﬁlterServicing the air ﬁlter Emptying the particle trapChecking the Tyre Pressures Bleeding the fuel systemServicing the fuel ﬁlter MaintenanceFuses Servicing the batteryWhat to do in case of contact with battery acid External Rinse thoroughly with waterChecking the Safety System Replacing the bulb in the headlight MaintenanceIMPORTANT INFORMATION Attaching and removing the cutting unit Light settingThe Cutting Unit Components Side shifting the cutting unitMaintenance 4. Stop the engine 5. Remove the pins on both sidesIMPORTANT INFORMATION Maintenance Setting the cutting height and tilt angleCutting height IMPORTANT INFORMATIONTilt angle The Cutting Unit’s Service PositionPlacing in the Service Position Ground pressureReleasing the Service Position Cutting Unit ModelMaintenance Always replace the belts in pairs Replacing the power take-off beltsChecking the Blades MaintenanceReplacing the belt on the Combi unit Adjusting the power take-off beltsReplacing the cutting unit belt MaintenanceRemoval of BioClip Plug MaintenanceGeneral Chapter 7 LubricationLubrication Schedule Lubricating the cables1. Pivot wheel bearings 2. Handle for cutting height settingLubricating in Accordance with the 3. Cutting unit’s bevel gear7. Engine Oil 6. The power take-off shaft’s front support bearing5. Lift cylinder Viscosity and qualityAvoid skin contact wash with soap and water in case of spills Filling engine oilChanging the Engine Oil 1. Position the wheels fully to the leftInspection off the oil level 7. Replacing the engine’s oil ﬁlter8. Hydraulic oil Filling hydraulic oil10. Lifting arm’s rear bearings 8. Hydraulic oil ﬁlter, change9. Cutting unit mounting 11. Driver’s Seat12. Parking brake cables 13. Control cylinderLubrication Lubrication Problem Chapter 8 Trouble Shooting GuideTrouble Shooting Guide CauseTrouble Shooting Guide ProblemCause Cause Trouble Shooting GuideProblem Uneven mowing resultsTrouble Shooting Guide Chapter 9 Storage Winter StorageStorage Service StorageChapter 10 Electrical system Electrical systemElectrical system, component locations Chapter 11 Hydraulic System Hydraulic SystemKeep the hydraulic system clean. Remember to Hydraulic SystemChapter 12 Fuel system Fuel systemData Technical DataTechnical Data PT 26DTechnical Data DataPT 26D IMPORTANT INFORMATION Technical DataIMPORTANT INFORMATION DataTechnical Data EU Declaration of Conformity only applies to Europe Design standardsDesign standards Diverse design standardsDesign standards Page Page 1153893-26 ´z+Uy@¶6u¨ ´z+Uy@¶6u¨ Original instructions

Steering wheel console

Warning lamp Battery charging page 24

Warning lamp High speed page 24

Warning lamp Differential lock page 24

Warning lamp Right-hand indicator page 24

Warning lamp Coolant temperature page 24

Warning lamp Glow plug heating page 24

Warning lamp Full beam page 24

Warning lamp Engine oil pressure page 24

Warning lamp Left-hand indicator page 24

1-2. Speed control

Speed control

3. Parking brake

Parking brake