PLC/Device Protocol | ICP DAS USA DB25, 100-700 PLCS, DN-3000

DeviceNet to PLCs or Devices

CONFIGURING PORT #2 (PLCS OR DEVICES)

When the highlight bar is around the “Port 2 (PLCs/Devices)” sub-heading, press the ENTER key. This opens a window which allows you to select the type of PLCs or devices connected to this port and check all of the communication settings.

PORT # 2

PLC

Configuration

Window

PLC/Device Protocol

The window for PORT # 2 Configuration will open with the highlighted bar at the “PLC/DEVICE PROTOCOL” selection heading. If the displayed Protocol is not the one wanted, simply press the ENTER key and a smaller window will appear.

PLC/Device

Protocol

Selection

Window

12

Image 18

ICP DAS USA DB25, 100-700 PLCS, DN-3000 user manual PLC/Device Protocol, Configuring Port #2 Plcs or Devices

Contents

DN-3000 Page Warranty & Notices Warranty Table of Contents Application Notes Motor Drives Page Introduction Introduction Software Installation InstallationGeneral Information Software Information Software START-UP Creating Project Files Creating a Project File Project Types Additional Project Menu Sub-Headings DeviceNet to PLCs or Devices Devicenet to Plcs or DevicesDevice Profile Example Applications DeviceNet Host to Serial PLC with Pass-Through ConnectionDeviceNet Host to Multi-Dropped Serial PLCs Multiple DN-3000s with Different PLC or Device Types Configuring Port #1, Devicenet DeviceNet to PLCs or Devices Edit Menu MAC ID of DN3000 Configuring Port #2 Plcs or Devices PLC/Device Protocol Wire RS422 or RS485 Communications Configuring Port # 3 Passthrough Intermessage Time-Out Data Configuration Use I/O Data Output Data Size Use Command BlockUse Diagnostics Output Data Input Data Size Input Data Output Data Table File Number Allen-Bradley PLCs only Use Output WordPLC/Device Address Register Number Input Data Table Use Input Word PLC/DeviceAddress Command Block DeviceNet to Motor Drives Devicenet to Motor Drives DeviceNet Host to Serial Motor Drive DeviceNet Host to Multi-Dropped Serial Motor Drives Multiple DN-3000s with Different Motor Drive Types DeviceNet to Motor Drives Edit Menu MAC ID of DN3000 Configuring Port # 2 Motor Drives Motor Drive Type Minimum Delay Between Messages Data Configuration Use Command Block Input Data Size Output Data Table Motor Drive Address Parameter Number Input Data Table Use Input Word Word Motor Drive Address Result Code Command Word Motor Drive Address CommandNumber Word Parameter Data write command only Number Word Returned Parameter Data read command only Upper Link Configuration Mitsubishi Drives Only Operation of the Link Switch Exception Table Mitsubishi Drives Only Transferring Project Files Transferring Project Files Upload Project from DN3000 Transfer OptionsDownload Project to DN3000 Verify Options Settings Options SettingsSET Directory Current Directory Path Graphic Area SET COM Port Load Options from Disk Default OptionsSET Printer Options Save Options to Disk Power Requirements Physical DimensionsTechnical Information DIP Switch Settings Visual LED IndicatorsSwitch # Normal Off Configuration Diagnostic DN-3000 Troubleshooting Information Flashes followed by a pause Invalid DIP Switch SettingFlashes followed by a pause ALLEN-BRADLEY PLC 5, SLC500 and Micrologix Plcs Registers AccessedApplication Notes PLCs and Devices Protocols Supported Idec MICRO-3 Plcs Idec FA Series PlcsLink Adapter Requirement Memory Address PLC Registers Accessed Koyo / PLC Direct 205 Series Plcs Koyo / PLC Direct / TI 305 Series Plcs Omron Plcs Mitsubishi FX Series PlcsModicon Plcs and Modbus Devices RTS Control Protocol Information Pass-Through Port Square D Model 100-700 Plcs Passthrough Port Note Toshiba EX and M Series Plcs Toshiba T Series PlcsWestinghouse Plcs Application Notes Motor Drives Baldor Motor DrivesDrive Parameter Numbers Assigned By Panel-Tec Configuring a Baldor Drive For Serial Communications Drive Addresses Assigned By Panel-Tec Woods Motor Drives Configuring a Woods Drive For Serial CommunicationsMitsubishi Motor Drives Yaskawa Motor Drives Cable Diagrams DN3000 Configuration Cable Allen Bradley Solder End GE Fanuc 90/20, 30 GE Fanuc DN3000 Idec Koyo/PLC Direct Mitsubishi FX Series Mitsubishi Modicon Modicon Omron Host Link Siemens S7 Square D TSX07 Simatic TI5 Series TI5 232 Port DN3000 Toshiba Toshiba DN3000 Baldor Motor Drives Baldor Mitsubishi Motor Drives Woods Motor Drives Yaskawa Motor Drives DeviceNet Cable DeviceNet DN3000