ICP DAS USA 100-700 PLCS, DB25, DN-3000 instruction

DeviceNet to Motor Drives

Multiple DN-3000s with Different Motor Drive Types

DeviceNet Host

2 3

DN-3000

# 1

Drive # 1

Brand A

Drive # 2 Brand A

2

3

2

3

2

3

DN-3000

DN-3000

DN-3000

# 2

# 3

# 4

Drive # 1		Drive # 1			Drive # 1

Brand S		Brand O			Brand M

Drive # 2

Brand O

RS-422/485 Multiple-Drop Networks

2 3

DN-3000

# 5

Drive # 1 Brand I

Drive # 2 Brand I

Drive # 3 Brand I

NOTE:

1)Each DN-3000 can support up to 32 Motor Drives (if they are network addressable internally).

2)The DeviceNet Host can address a maximum of 63 DN-3000 units.

3)Multiple Brands of Motor Drives may be addressed by the DeviceNet Host by using multiple DN-3000s, but only one Motor Drive Type may be used on a single DN-3000 unit.

4)If multiple DN-3000s are to be used, each DN-3000 must be configured with a unique node address (MAC ID) on the DeviceNet network.

25

Image 31

ICP DAS USA 100-700 PLCS, DB25 user manual Multiple DN-3000s with Different Motor Drive Types

Contents

DN-3000 Page Warranty Warranty & Notices Table of Contents Application Notes Motor Drives Page Introduction Introduction Installation Software InstallationGeneral Information Software START-UP Software Information Creating a Project File Creating Project Files Project Types Additional Project Menu Sub-Headings Devicenet to Plcs or Devices DeviceNet to PLCs or DevicesDevice Profile DeviceNet Host to Serial PLC with Pass-Through Connection Example ApplicationsDeviceNet Host to Multi-Dropped Serial PLCs Multiple DN-3000s with Different PLC or Device Types DeviceNet to PLCs or Devices Edit Menu Configuring Port #1, Devicenet MAC ID of DN3000 PLC/Device Protocol Configuring Port #2 Plcs or Devices Wire RS422 or RS485 Communications Intermessage Time-Out Configuring Port # 3 Passthrough Use I/O Data Data Configuration Output Data Use Command BlockUse Diagnostics Output Data Size Input Data Input Data Size Output Data Table Register Number Use Output WordPLC/Device Address File Number Allen-Bradley PLCs only Input Data Table PLC/DeviceAddress Use Input Word Command Block Devicenet to Motor Drives DeviceNet to Motor Drives DeviceNet Host to Multi-Dropped Serial Motor Drives DeviceNet Host to Serial Motor Drive Multiple DN-3000s with Different Motor Drive Types DeviceNet to Motor Drives Edit Menu MAC ID of DN3000 Motor Drive Type Configuring Port # 2 Motor Drives Minimum Delay Between Messages Data Configuration Use Command Block Input Data Size Output Data Table Parameter Number Motor Drive Address Input Data Table Use Input Word Number Word Returned Parameter Data read command only Word Motor Drive Address CommandNumber Word Parameter Data write command only Word Motor Drive Address Result Code Command Operation of the Link Switch Upper Link Configuration Mitsubishi Drives Only Exception Table Mitsubishi Drives Only Transferring Project Files Transferring Project Files Verify Transfer OptionsDownload Project to DN3000 Upload Project from DN3000 Options Settings Options SettingsSET Directory Current Directory Path Graphic Area SET COM Port Save Options to Disk Default OptionsSET Printer Options Load Options from Disk Physical Dimensions Power RequirementsTechnical Information Visual LED Indicators DIP Switch SettingsSwitch # Normal Off Configuration Diagnostic Flashes followed by a pause Invalid DIP Switch Setting DN-3000 Troubleshooting InformationFlashes followed by a pause Protocols Supported Registers AccessedApplication Notes PLCs and Devices ALLEN-BRADLEY PLC 5, SLC500 and Micrologix Plcs Idec FA Series Plcs Idec MICRO-3 PlcsLink Adapter Requirement Koyo / PLC Direct 205 Series Plcs Memory Address PLC Registers Accessed Koyo / PLC Direct / TI 305 Series Plcs RTS Control Mitsubishi FX Series PlcsModicon Plcs and Modbus Devices Omron Plcs Pass-Through Port Protocol Information Passthrough Port Note Square D Model 100-700 Plcs Toshiba T Series Plcs Toshiba EX and M Series PlcsWestinghouse Plcs Baldor Motor Drives Application Notes Motor DrivesDrive Parameter Numbers Assigned By Panel-Tec Drive Addresses Assigned By Panel-Tec Configuring a Baldor Drive For Serial Communications Yaskawa Motor Drives Configuring a Woods Drive For Serial CommunicationsMitsubishi Motor Drives Woods Motor Drives DN3000 Configuration Cable Cable Diagrams Solder End Allen Bradley GE Fanuc DN3000 GE Fanuc 90/20, 30 Idec Koyo/PLC Direct Mitsubishi Mitsubishi FX Series Modicon Modicon Host Link Omron Siemens S7 TSX07 Square D TI5 232 Port DN3000 Simatic TI5 Series Toshiba DN3000 Toshiba Baldor Baldor Motor Drives Mitsubishi Motor Drives Woods Motor Drives Yaskawa Motor Drives DeviceNet DN3000 DeviceNet Cable