Siemens S7 | ICP DAS USA DN-3000, DB25, 100-700 PLCS guide

Cable Diagrams

Siemens S7

	PLC/Drive		DN3000
	DB9 Male		DB25 Male
PART # 7000-6045	D+	03 ------------------------------	23	TX+
	D -	08 ------------------------------	24	RX+
	D -	08 ------------------------------	21	TX -
CABLE TYPE			22	RX -
3 or 4 Conductor Round			04	RTS
			05	CTS
	GND 05 ------------------------------		07	GND

Note: To connect additional PLC’s, daisy-chain Pin 3 of each PLC together and daisy-chain Pin 8 of each PLC together before connecting both signals to the DN3000.

S7 PLC	S7 PLC	DN3000
DB9 Male	DB9 Male	DB25 Male
03	------------------------------ 03 ------------------------------	23	TX+
08		24	RX+
08	------------------------------ 08 ------------------------------	21	TX -
		22	RX -
		04	RTS
05		05	CTS
05	------------------------------ 05 ------------------------------	07	GND

68

Image 74

ICP DAS USA DN-3000, DB25, 100-700 PLCS user manual Siemens S7

Contents

DN-3000 Page Warranty & Notices Warranty Table of Contents Application Notes Motor Drives Page Introduction Introduction General Information Software InstallationInstallation Software Information Software START-UP Creating Project Files Creating a Project File Project Types Additional Project Menu Sub-Headings Device Profile DeviceNet to PLCs or DevicesDevicenet to Plcs or Devices DeviceNet Host to Multi-Dropped Serial PLCs Example ApplicationsDeviceNet Host to Serial PLC with Pass-Through Connection Multiple DN-3000s with Different PLC or Device Types Configuring Port #1, Devicenet DeviceNet to PLCs or Devices Edit Menu MAC ID of DN3000 Configuring Port #2 Plcs or Devices PLC/Device Protocol Wire RS422 or RS485 Communications Configuring Port # 3 Passthrough Intermessage Time-Out Data Configuration Use I/O Data Output Data Size Use Command BlockUse Diagnostics Output Data Input Data Size Input Data Output Data Table File Number Allen-Bradley PLCs only Use Output WordPLC/Device Address Register Number Input Data Table Use Input Word PLC/DeviceAddress Command Block DeviceNet to Motor Drives Devicenet to Motor Drives DeviceNet Host to Serial Motor Drive DeviceNet Host to Multi-Dropped Serial Motor Drives Multiple DN-3000s with Different Motor Drive Types DeviceNet to Motor Drives Edit Menu MAC ID of DN3000 Configuring Port # 2 Motor Drives Motor Drive Type Minimum Delay Between Messages Data Configuration Use Command Block Input Data Size Output Data Table Motor Drive Address Parameter Number Input Data Table Use Input Word Word Motor Drive Address Result Code Command Word Motor Drive Address CommandNumber Word Parameter Data write command only Number Word Returned Parameter Data read command only Upper Link Configuration Mitsubishi Drives Only Operation of the Link Switch Exception Table Mitsubishi Drives Only Transferring Project Files Transferring Project Files Upload Project from DN3000 Transfer OptionsDownload Project to DN3000 Verify SET Directory Options SettingsOptions Settings Current Directory Path Graphic Area SET COM Port Load Options from Disk Default OptionsSET Printer Options Save Options to Disk Technical Information Power RequirementsPhysical Dimensions Switch # Normal Off Configuration Diagnostic DIP Switch SettingsVisual LED Indicators Flashes followed by a pause DN-3000 Troubleshooting InformationFlashes followed by a pause Invalid DIP Switch Setting ALLEN-BRADLEY PLC 5, SLC500 and Micrologix Plcs Registers AccessedApplication Notes PLCs and Devices Protocols Supported Link Adapter Requirement Idec MICRO-3 PlcsIdec FA Series Plcs Memory Address PLC Registers Accessed Koyo / PLC Direct 205 Series Plcs Koyo / PLC Direct / TI 305 Series Plcs Omron Plcs Mitsubishi FX Series PlcsModicon Plcs and Modbus Devices RTS Control Protocol Information Pass-Through Port Square D Model 100-700 Plcs Passthrough Port Note Westinghouse Plcs Toshiba EX and M Series PlcsToshiba T Series Plcs Drive Parameter Numbers Assigned By Panel-Tec Application Notes Motor DrivesBaldor Motor Drives Configuring a Baldor Drive For Serial Communications Drive Addresses Assigned By Panel-Tec Woods Motor Drives Configuring a Woods Drive For Serial CommunicationsMitsubishi Motor Drives Yaskawa Motor Drives Cable Diagrams DN3000 Configuration Cable Allen Bradley Solder End GE Fanuc 90/20, 30 GE Fanuc DN3000 Idec Koyo/PLC Direct Mitsubishi FX Series Mitsubishi Modicon Modicon Omron Host Link Siemens S7 Square D TSX07 Simatic TI5 Series TI5 232 Port DN3000 Toshiba Toshiba DN3000 Baldor Motor Drives Baldor Mitsubishi Motor Drives Woods Motor Drives Yaskawa Motor Drives DeviceNet Cable DeviceNet DN3000