Motor Drive Type | ICP DAS USA 100-700 PLCS, DB25, DN-3000 guide

DeviceNet to Motor Drives

CONFIGURING PORT # 2 (MOTOR DRIVES)

Using the DOWN arrow key, move the highlight bar to the “Port 2 (Motor Drives)” sub-heading (within the “EDIT” menu) and press the ENTER key. This action opens the Motor Drive selection screen to allow you to select the drive manufacturer and to check all the motor drive’s communications settings.

Motor Drive Type

The Port 2 (Motor Drives) Configuration screen will open with the highlight bar at the “MOTOR DRIVE TYPE” selection area. Simply press the ENTER key to open the current list of supported motor drives. Use your UP/DOWN arrow keys to move through the drive list and place the highlight bar around the drive of your choice, then press the ENTER key to enter your selection. The software automatically saves your entry and closes the “MOTOR DRIVE SELECTION” window.

Motor Drive

Selection

Window

28

Image 34

ICP DAS USA 100-700 PLCS, DB25, DN-3000 user manual Motor Drive Type, Configuring Port # 2 Motor Drives

Contents

DN-3000 Page Warranty & Notices Warranty Table of Contents Application Notes Motor Drives Page Introduction Introduction Installation Software InstallationGeneral Information Software Information Software START-UP Creating Project Files Creating a Project File Project Types Additional Project Menu Sub-Headings Devicenet to Plcs or Devices DeviceNet to PLCs or DevicesDevice Profile DeviceNet Host to Serial PLC with Pass-Through Connection Example ApplicationsDeviceNet Host to Multi-Dropped Serial PLCs Multiple DN-3000s with Different PLC or Device Types Configuring Port #1, Devicenet DeviceNet to PLCs or Devices Edit Menu MAC ID of DN3000 Configuring Port #2 Plcs or Devices PLC/Device Protocol Wire RS422 or RS485 Communications Configuring Port # 3 Passthrough Intermessage Time-Out Data Configuration Use I/O Data Output Data Size Use Command BlockUse Diagnostics Output Data Input Data Size Input Data Output Data Table File Number Allen-Bradley PLCs only Use Output WordPLC/Device Address Register Number Input Data Table Use Input Word PLC/DeviceAddress Command Block DeviceNet to Motor Drives Devicenet to Motor Drives DeviceNet Host to Serial Motor Drive DeviceNet Host to Multi-Dropped Serial Motor Drives Multiple DN-3000s with Different Motor Drive Types DeviceNet to Motor Drives Edit Menu MAC ID of DN3000 Configuring Port # 2 Motor Drives Motor Drive Type Minimum Delay Between Messages Data Configuration Use Command Block Input Data Size Output Data Table Motor Drive Address Parameter Number Input Data Table Use Input Word Word Motor Drive Address Result Code Command Word Motor Drive Address CommandNumber Word Parameter Data write command only Number Word Returned Parameter Data read command only Upper Link Configuration Mitsubishi Drives Only Operation of the Link Switch Exception Table Mitsubishi Drives Only Transferring Project Files Transferring Project Files Upload Project from DN3000 Transfer OptionsDownload Project to DN3000 Verify Options Settings Options SettingsSET Directory Current Directory Path Graphic Area SET COM Port Load Options from Disk Default OptionsSET Printer Options Save Options to Disk Physical Dimensions Power RequirementsTechnical Information Visual LED Indicators DIP Switch SettingsSwitch # Normal Off Configuration Diagnostic Flashes followed by a pause Invalid DIP Switch Setting DN-3000 Troubleshooting InformationFlashes followed by a pause ALLEN-BRADLEY PLC 5, SLC500 and Micrologix Plcs Registers AccessedApplication Notes PLCs and Devices Protocols Supported Idec FA Series Plcs Idec MICRO-3 PlcsLink Adapter Requirement Memory Address PLC Registers Accessed Koyo / PLC Direct 205 Series Plcs Koyo / PLC Direct / TI 305 Series Plcs Omron Plcs Mitsubishi FX Series PlcsModicon Plcs and Modbus Devices RTS Control Protocol Information Pass-Through Port Square D Model 100-700 Plcs Passthrough Port Note Toshiba T Series Plcs Toshiba EX and M Series PlcsWestinghouse Plcs Baldor Motor Drives Application Notes Motor DrivesDrive Parameter Numbers Assigned By Panel-Tec Configuring a Baldor Drive For Serial Communications Drive Addresses Assigned By Panel-Tec Woods Motor Drives Configuring a Woods Drive For Serial CommunicationsMitsubishi Motor Drives Yaskawa Motor Drives Cable Diagrams DN3000 Configuration Cable Allen Bradley Solder End GE Fanuc 90/20, 30 GE Fanuc DN3000 Idec Koyo/PLC Direct Mitsubishi FX Series Mitsubishi Modicon Modicon Omron Host Link Siemens S7 Square D TSX07 Simatic TI5 Series TI5 232 Port DN3000 Toshiba Toshiba DN3000 Baldor Motor Drives Baldor Mitsubishi Motor Drives Woods Motor Drives Yaskawa Motor Drives DeviceNet Cable DeviceNet DN3000