Integra DTR-10.5 Installing the Option Boards, Check the alphabet letter on the option board

Before Using the DTR-10.5—Continued

Installing the Option Boards

The option boards should be installed in their individual designated slots. Installing the option board a different slot may cause failure.

1 Turn off the power and unplug the power cord both from the DTR-10.5 and electrical outlet.

Be sure to turn off the power of the DTR-10.5. Inserting or removing an option board with the DTR-10.5 turned on may cause failure.

2 Take the option board out from the pack- age carefully.

The option board incorporates many components, terminals and connectors along with solderings on its surface. Touching the board with your fin- gers may cause failure or damage from static elec- tricity, incorrect contact and so on. When handling the board, be sure to hold the outer part or panel section of the board without touching the board surface.

Board surface

The sub-panels are fixed to the DTR-10.5 with two screws at the top and bottom, while the panel that covers slots [H] and [I] is fixed with four screws at the top and bottom. Keep the removed screws for fixing the option board.

B

				DIGITAL	IN	E
			D
	C	DIGITAL	IN	COAXIAL
		OPTICAL
	B		1
A		1
			2
		2
			3
		3
			4
		4
	S400		5
		5
			6
AUDIO		6
	a		1
K logo is		1
The i.LIN s of Sony
trademark n, registered
Corporatio and other
in the U.S.
countries.		2	2
			OUT
				(ASSIGNABL		E)

			L
			(SINGLE)
L							SURR	R
	CENTER		R			SURR BAC	K R
				SUBWOO		FER
R			K	PRE OU	T A
		SURR	SURR BACE)
	SUB		(ASSIGNABL
FRONT	WOO

5 Insert the option board along the rail softly. When the board comes to the posi- tion where it stops but does not cover the slot completely, push the board forward a little bit more strongly.

Getting Started

B

TuneNet-)( ETHERNET Onkyo isa “Net- Corporation trademark Tune” of .

A

				S400
AUDIO
K logo is				a
The i.LIN	of	Sony
trademarks		egistered
Corporation, r			other
in the U.S.. and
countries

C

E

	D	DIGITAL	IN
DIGITAL	IN	COAXIAL
OPTICAL
	1
B	2

2
3
3
4
4
is“Naettr-Taudneem”ark otiof	n.
Onkyo Corpora
5
5
6
6
ETHERNET)
(Net-Tune
1
1
2
2
OUT

(ASSIGNABL E)

3 Check the alphabet letter on the option board.

The alphabet letter is printed at the top left corner of the panel section.

B

“Net	-Tune”					B
			ark of
is a tradem				ration.
Onkyo Corpo
	ETH	ERNET
					)
	(Net-Tune

4 Remove the sub-panel with the same alphabet letter as your option board from the back of the DTR-10.5.

Use the supplied Allen wrench to loosen the screw gradually, while holding the sub-panel so that the panel will not drop down.

			L
			(SINGLE)
L						SURR	R
	CENTER		R		SURR BAC	K R
				SUBWOO	FER
			K
R		SURR	SURR BACE)	PRE OU
	SUB		(ASSIGNABL
FRONT	WOO

6 Fix the option board firmly to the DTR-10.5 using the removed screws.

Be sure to tighten the screws firmly to the DTR-10.5. If the screws are loose, contact failures for ground or signal wires may occur at the section between the DTR-10.5’s slot terminal and the option board, which may cause the DTR-10.5 or board to fail.

DIGITAL

IN

E

D

C

DIGITAL

IN

COAXIAL

OPTICAL

B

1

A

1

2

2

3

is“Naettr-Taudneem”ark otiof

3

n.

Onkyo Corpora

4

4

S400

5

5

ETHERNET)

(Net-Tune

6

AUDIO

6

a

1

The

i.LINK logo isny

1

marks of So

ered

Ctraodrpeoration, rdegoisthert

in the U.S. an

countries.

2

2

OUT

(ASSIGNABL

E)

L

(SINGLE)

L

SURR

R

CENTER

R

SURR BAC

K R

SUBWOO

FER

R

K

PRE OU

T A

SURR

SURR BACE)

SUB

(ASSIGNABL

FRONT

WOO

11