Speaker/Output Setup

The DTR-10.5 provides a wide range of variations in speaker connections and speaker settings, so you have to specify speaker settings according to conditions of each variation. For proper selection of an AV device connected at switching of the input type, you also need to allocate “audio output” and “video output” to each input type. If this allocation is incorrect, the desired component will not play a selected input source.

Please setup correctly by referring to the information you wrote down in the Your System Settings booklet.

Speaker Configuration Sub-menu

Specify the rooms where you want to use speakers connected to the SPEAKERS A terminal and the SPEAKERS B terminal. Specify according to settings for main room A.

Note:

Basically, a speaker set with the maximum number of speakers should be connected to the SPEAKERS A terminals and configured for main room A (Main A). When either the center, surround, or surround back speakers are not connected to the SPEAKERS A terminals, or any of these speakers is set to “Not Used” in the Speaker A settings, you cannot perform the settings for the corresponding speakers connected to the SPEAKERS B terminals and those speakers connected to the SPEAKERS B terminals cannot be used.

(Speaker A) Front L/R

The setting of the front speakers is initially fixed to Main A.

Always install speakers connected to FRONT L/R of SPEAKERS A in main room A.

(Speaker A) Center, Surr L/R

Main A (default): Select this when using the center speaker and/or surround speakers in main room A. Not Used: Select this when not using a center speaker or surround speakers.

(Speaker A) Surr Back

Main A 2ch (default): If Surr L/R is set to “Main A,” you can select this item. Select this when connecting and using two surround back speakers in main room A. Main A 1ch (SBL): If Surr L/R is set to “Main A,” you can select this item. Select this when connecting and using a surround back speaker in main room A.

BTL for Front: Select this when using the front speaker in main room A by connecting the surround back channel to the speaker via BTL (See page 29). Bi-Amp for Front: Select this when using the front speaker in main room A by connecting the front channel and the surround back channel to the speaker via Bi- Amp (See page 29).

Not Used: Select this when not using surround back speakers.

Note:

If “Not Used” is selected for Surr L/R, this item defaults to “Not Used.”

(Speaker A) Subwoofer

Main A (default): Select this when using a subwoofer in the main room A.

Not Used: Select this when not using a subwoofer in the main room A.

(Speaker B) Front L/R

Main A: Select this when using in main room A.

Main B: Select this when using in main room B.

Not Used (default): Select this when not using.

(Speaker B) Center

Main A: Select this when using in main room A.

Main B: Select this when using in main room B. This setting can only be made when you set the “(Speaker B) Front L/R” setting to “Main B.”

Not Used (default): Select this when not using.

(Speaker B) Surr L/R

Main A: Select this when using in main room A.

Main B: Select this when using in main room B. This setting can only be made when you set the “(Speaker B) Front L/R” setting to “Main B.”

Not Used (default): Select this when not using.

(Speaker B) Surr Back

Main A 2ch: Select this when connecting and using two surround back speakers in main room A.

Main A 1ch (SBL): Select this when connecting and using a surround back speaker in main room A.

Main B 2ch: If (Speaker B) Front L/R and Surr L/R are both set to “Main B,” you can select this item. Select this when connecting and using two surround back speakers in main room B.

Main B 1ch (SBL): If (Speaker B) Front L/R and Surr L/R are both set to “Main B,” you can select this item. Select this when connecting and using a surround back speaker in main room B.

Powered Zone 2: Select this when using in Zone 2.

If (Speaker A) Surr Back is set to “BTL for Front” or “Bi-Amp for Front,” this item is not displayed (Because, if “Powered Zone 2” is set, BTL

connection and/or Bi-Amp connection are disabled). BTL for Front: This setting can be made only when you set the “(Speaker B) Front L/R” setting to “Main A” or “Main B.” Select this when using the front speaker in main room B by connecting the surround back channel to the speaker via BTL (See page 29).

88

Page 88
Image 88
Integra DTR-10.5 instruction manual Speaker/Output Setup, Speaker Configuration Sub-menu