Listening Mode Setup—Continued

e. Surr Bk Speaker

This option configures the surround back speakers to use when playing the source. Select the speaker terminals to which the speakers you want to use are connected. This setting can be made when the “(Speaker B) Surr Back” is set to “Main A” in the Speaker Configuration sub-menu. However, when the “(Speaker A) Surr Back” is set to “BTL for Front,” “Bi- Amp for Front,” or “Not Used,” this setting will not be displayed.

When the impedance setting for “Surr L/R A” or “Surr L/R B” in the Speaker Impedance sub-menu is set to “6 ohms” or “4 ohms,” the available options will be “A” and “B.”

When the settings for “(Speaker A) Surr Back” and “(Speaker B) Surr Back” in the Speaker Configuration

sub-menu differ, the available options will be “A” and “B.”

A (Default): Outputs the source from the speakers connected to the SURR BACK L/R SPEAKERS A terminals.

B:Outputs the source from the speakers connected to the SURR BACK L/R SPEAKERS B terminals. A+B: Outputs the source from the speakers connected to the SURR BACK L/R SPEAKERS A and SURR BACK L/R SPEAKERS B terminals.

f. Subwoofer

This option configures the subwoofer to use when playing the source. Select the terminal to which the subwoofer you want to use is connected. This setting can be made when the “(Speaker A) Subwoofer” is set to an option other than “Not Used” in the Speaker Configuration sub-menu. However, when the “(Speaker

B)Subwoofer” is set to an option other than “Main A” in the Speaker Configuration sub-menu, the available options will be “A” or “Not Used.”

A (Default): Outputs the source only from the subwoofer connected to the SUBWOOFER PRE OUT A terminal.

B: Outputs the source only from the subwoofer connected to the SUBWOOFER PRE OUT B terminal. A+B: Outputs the source from the subwoofers connected to the SUBWOOFER PRE OUT A and SUBWOOFER PRE OUT B terminals.

Not Used: No subwoofers are used for playback.

Dolby Virtual Speaker Setup Sub- menu

This sub-menu allows you to configure the playback options when you use the Dolby Virtual Speaker effect.

a. Mode (2ch or 3ch only)

This option allows you to configure the width of a virtual sound image which is simulated using two or three speakers while you use the Dolby Virtual Speaker effect. Wide: The breadth of the sound image is emphasized.

Reference (Default): The general 5.1ch surround sound is simulated.

b. Front Speaker

This option configures the front speakers to use when playing the source. Select the speaker terminals to which the speakers you want to use are connected. This setting can be made when the “(Speaker B) Front L/R” is set to “Main A” in the Speaker Configuration sub- menu.

• When the impedance setting for “Front L/R A” or “Front L/R B” in the Speaker Impedance sub-menu is set to “6 ohms” or “4 ohms,” the available options will be “A” and “B.”

A (Default): Outputs the source from the speakers connected to the FRONT L/R SPEAKERS A terminals.

B:Outputs the source from the speakers connected to the FRONT L/R SPEAKERS B terminals.

A+B: Outputs the source from the speakers connected to the FRONT L/R SPEAKERS A and FRONT L/R SPEAKERS B terminals. Note that this option is not available when the front speakers are in Bi-amp or in BTL configuration.

c. Center Speaker

This option configures the center speaker to use when playing the source. Select the speaker terminal to which the speaker you want to use is connected. This setting can be made when the “(Speaker B) Center” is set to “Main A” in the Speaker Configuration sub-menu.

When the impedance setting for “Center A” or “Center B” in the Speaker Impedance sub-menu is set to “6 ohms” or “4 ohms,” the available options will be “A” and “B.”

A (Default): Outputs the source from the speaker connected to the CENTER SPEAKERS A terminal.

B:Outputs the source from the speaker connected to the CENTER SPEAKERS B terminal.

A+B: Outputs the source from the speakers connected to the CENTER SPEAKERS A and CENTER SPEAKERS B terminals.

d. Surr L/R Sp

This option configures the surround speakers to use when playing the source. Select the speaker terminals to which the speakers you want to use are connected. This setting can be made when the “(Speaker B) Surr L/R” is set to “Main A” in the Speaker Configuration sub-menu.

When the impedance setting for “Surr L/R A” or “Surr L/R B” in the Speaker Impedance sub-menu is set to “6 ohms” or “4 ohms,” the available options will be “A” and “B.”

A (Default): Outputs the source from the speakers connected to the SURR L/R SPEAKERS A terminals.

B:Outputs the source from the speakers connected to the SURR L/R SPEAKERS B terminals.

116

Page 116
Image 116
Integra DTR-10.5 instruction manual 116, Dolby Virtual Speaker Setup Sub- menu, Mode 2ch or 3ch only