Integra DTR-10.5 Connection Using the i.LINK AUDIO Terminal, What is i.LINK AUDIO

Connecting AV Components—Continued

Connection Using the i.LINK (AUDIO) Terminal ( )

The i.LINK (AUDIO) terminal is available when the i.LINK terminal board [A] is installed.

What is i.LINK

i.LINK is an appellation of IEEE1394, which is the digital interface standard defined by the Institute of Electrical and Electronics Engineers (IEEE).

Connecting i.LINK (AUDIO)-supported devices allows high speed transfer of data such as digital sound between the linked devices, and their control.

What is i.LINK (AUDIO)

The DTR-10.5 supports “i.LINK (AUDIO)” of the i.LINK transfer format. Accordingly, “i.LINK (AUDIO)” must also be supported for other devices that you want to connect to the DTR-10.5. The DTR-10.5 does not support other i.LINK transfer formats such as “MPEG-2 TS” used for BS digital broadcasts or “DV” used for DVD recorders, digital video, etc. The DTR-10.5 connected to other i.LINK(AUDIO)-supported devices via i.LINK cable enables you to transfer multichannel digital sound such as DVD-Audio and SACD (video signal is not supported).

Even when multiple devices are connected to each other, you can perform data transfer and control of target devices via another device.

The IEEE interfaces on the DTR-10.5 are designed conforming to the standards below.

1.IEEE Std 1394a-2000, Standard for a High Performance Serial Bus

2.IEC60958 bitstream, DVD-Audio, and SACD in the AM824 Sequence adaptation layers of Audio and Music Data Transmission Protocol 2.0

Copyright Protection System

The DTR-10.5 supports the DTCP (Digital Transmission Contents Protection) system. The DTCP system uses tech- nologies for data encryption and authentication during the data transfer between the i.LINK-connected digital devices in order to protect the copyright of the content against illegal duplication. To enjoy replaying DVD-Audio, etc., the DTCP must also be supported by other devices connected to the DTR-10.5.

How to Make a Connection through the i.LINK (AUDIO) Interface

Use the S400 4-pin i.LINK cable to connect the i.LINK (AUDIO) terminal on the DTR-10.5 to the i.LINK (AUDIO) terminal on the i.LINK (AUDIO)-enabled device.

•When using the i.LINK connection, you need to configure the audio input assignment settings in the “i.LINK” sec- tion of the Audio Assign sub-menu (Some i.LINK-connected devices may require audio output settings).

•The DTR-10.5 supports only audio signal transmission through the i.LINK (AUDIO) interface. When connecting video devices, you need to make a connection using other terminals for video signal.

Note:

If any other Integra product is connected to the DTR-10.5 via i.LINK, system operation can be achieved via i.LINK cable. In that

case, disconnect the connection as it may introduce errors.

VIDEO OUT

In addition to the i.LINK audio connection, make sure to connect the terminals for images such as VIDEO and/or S VIDEO terminals.

A B C DIGITAL IN

OPTICAL

1

2

“Net-Tune”

is a trademark of 3 Onkyo Corporation.

4

ETHERNET 5

(Net-Tune)

6

1

D DIGITAL IN	E	- CH	F	AUDIO IN	G		H S VIDEO	VIDEO
		MULTI	R	L	R	L
COAXIAL	FR	FL IN 1					IN	IN
1			PH		4		1
	SUB	C
2					5		2
				GND
	SR	SL	R	L
3			1		6		3
	SBR	SBL
4			2		7		4
	FR	FL
5			3		8		5
	SUB	C
6			1		9		6
	SR	SL
1			2		4		1

I	COMPONENT	J		K	L
	VIDEO
IN 1	IN 2	COMPONENT VIDEO			ANTENNA
		(HD/BNC)	IN
	Y		Y
	PB
			PB
	PR				FM
OUT 1	IN 3				75
	Y		PR
			OUT
	PB		Y
					AM

PR

PB

3

SBR SBL

42