Integra DTR-10.5 Connecting AV Components—Continued, Connections, Installation and

Connecting AV Components—Continued

Connecting a Recording Device such as MD Recorder, DAT Deck, CD Recorder or Cassette Deck

•When connecting a MD recorder, DAT deck or CD recorder to the DTR-10.5, make connections using digital or analog terminals. Before making connections, refer to page 32 for correct connections.

•Connect a cassette or DAT tape deck to TAPE1, and an MD or CD recorder to TAPE 2.

•When you connect a cassette deck to the DTR-10.5, be sure to use only analog audio terminals. In the initial settings, no terminal of this unit is assigned to a REC terminal of the cassette deck. To achieve the assignment, connect the REC terminal of the cassette deck to any of the AUDIO OUT 1 to 5 terminals and set the terminal to “Tape 1 Rec Out” in the Audio Output Assign sub-menu (See page 91). In addition, you can switch the input source “TAPE2” to MD or CDR. Press the [Tape 2] button on the front panel to display “TAPE 2,” then press the [Tape 2] button again and hold it for 3 seconds. This changes the display to “MD.” If you wish to change it to “CDR,” release the button once, and press and hold it again for 3 seconds. This operation enables you to operate Onkyo’s MD or CD recorders

with the remote controller of this unit (Please note that the connection is required).

•When connecting to other terminals, remember to configure the audio input assignment in the Audio Assign sub- menu (See page 94) and the audio output assignment in the Audio Output Assign sub-menu (See page 91).

•You can change the display name for the input source to represent the actual connected device (See page 97).

•When you want to perform analog recording of an audio signal or operate your -compatible Integra products via

connections with the DTR-10.5, you have to make analog audio signal connections. Connect the audio output terminals on the source device to the AUDIO IN terminals on the DTR-10.5 using analog audio cables (RCA/ phono).

Example for connecting with the TAPE 1 as input

Connections

Cassette deck or DAT deck

When connecting to other digital audio ter- minals or to other analog audio output ter- minals, configure the audio output settings accordingly using the Audio Output Assign sub-menu (See page 91).

AUDIO IN	AUDIO OUT	AUDIO OUT
DIGITAL	DIGITAL	ANALOG
OPTICAL	OPTICAL	R	L

When connecting to other audio terminals within the same terminal section, configure the audio input settings accordingly using the Audio Assign sub-menu (See page 94).

Installation and

A	B	C DIGITAL IN	D DIGITAL IN
		OPTICAL	COAXIAL
		1	1
		2	2
	“Net-Tune”	3	3
	is a trademark of
	Onkyo Corporation.
		4	4
	ETHERNET	5	5
	(Net-Tune)
		6	6
		1	1

E		- CH	F	AUDIO IN	G
		MULTI	R	L	R	L
FR	FL	IN 1
			PH		4
SUB		C
					5
				GND
SR		SL	R	L
			1		6

SBR SBL

27

FR FL

38

SUB	C
	1	9
SR	SL
	2	4
SBR	SBL

H S VIDEO VIDEO

IN IN

1

2

3

4

5

6

1

I	COMPONENT	J		K	L
	VIDEO
IN 1	IN 2	COMPONENT VIDEO			ANTENNA
		(HD/BNC)	IN
	Y		Y
	PB
			PB
	PR				FM
OUT 1	IN 3				75
	Y		PR
			OUT
	PB		Y
					AM

PR

PB

3

PR

	12 V	RS232
HDMI	TRIGGER
	OUT
	E
	IN 1
		IR IN

+12V DC PWR SUPPLY

20mA MAX.

GND

IN 2

MAIN

ZONE 2

ZONE 3

A 200mA MAX.

B 100mA MAX.

C 100mA MAX.

GND

D 100mA MAX.

E TOTAL

2	2
	OUT

3		5
R	L	OUT R	L

MULTI

-CH IN 2

2		4
	OUT	OUT
S VIDEO	VIDEO	VIDEO	S VIDEO

100mA MAX.

OUT

12V TRIGGER OUT

PRE OUT A SURR R SURR BACK R (ASSIGNABLE) FRONT R CENTER

FRONT L	SURR BACK L (ASSIGNABLE)	SURR L
	(SINGLE)

When connecting to other digital audio termi- nals or to other analog audio output terminals, configure the audio output settings accord- ingly using the Audio Output Assign sub- menu (See page 91).

MD recorder or CD recorder

AUDIO IN	AUDIO OUT	R	L
		AUDIO OUT
DIGITAL	DIGITAL
		ANALOG
OPTICAL	COAXIAL

When connecting to other audio ter- minals within the same terminal section, configure the audio input settings accordingly using the Audio Assign sub-menu (See page 94).

Example for connecting to the TAPE 2 as input

41