Integra DTR-10.5 Connecting -compatible AV Components, Connections for Remote Control

Connecting -compatible AV Components

The terminal on the DTR-10.5 is for connecting other Integra/Onkyo components equipped with the

same terminal. When a component is connected to

the terminal, it can be operated by the remote controller supplied with the DTR-10.5. In addition,

when you connect a component to the terminal, you can also perform the system operations given below.

Power on/ready function

When the DTR-10.5 is in the standby state, if an - connected component is turned on, the DTR-10.5 also turns on and the input source selected at the DTR-10.5 automatically switches to that component.

Be aware that this function will not work if the power cord for the -connected component is connected to the AC OUTLET on the DTR-10.5, or if the DTR-10.5 has already been turned on.

Direct change function

When the play button is pressed on an -connected component, the input source selected at the DTR-10.5 automatically changes to that component.

Power off function

When the DTR-10.5 is placed in the standby state, all

-connected components are also automatically put into the standby state.

Also, if you press the [On] button on the DTR-10.5 remote controller while the DTR-10.5 is turned on, all

-connected components (DVD players, CD players, MD recorders, tuners, etc.) are also turned on.

Integra DVD player	REMOTE
	CONTROL
L
R
ANALOG
OUTPUT	Remote
	control
	cable

Connections for Remote Control ()

To connect components using the terminal, simply

connect a remote control cable from this terminal to

the terminal of the other component. An remote control cable with a 1/8 inch (3.5 mm) miniature two- conductor plug comes with every cassette tape deck, compact disc player, MD recorder, and DVD player that

has an terminal.

•When performing operations with -connected

components using the system, do not use the remote zone (Zone 2/Zone3).

•For remote control operation, the audio connection cables must also be connected.

•If a component has two terminals, you can use either one to connect to the DTR-10.5. The other one can be used to daisy chain with another component.

•With Integra DVD players, you can enter the pre- program code so that you can operate the DVD player directly with the remote controller without connecting

the terminals (See page 129).

DTR-10.5

connector

Ex: Integra/Onkyo CD player

connector

Ex: Onkyo cassette tape deck

Remote control cable

Installation and Connections

AUDIO IN

R	L	REMOTE
		CONTROL

4

DIGITAL IN	DIGITAL IN				AUDIO IN			S VIDEO	VIDEO
OPTICAL	COAXIAL	FR	FL	R	L	R	L	IN	IN	IN 1	IN 2
1	1		PH			4		1			Y
		SUB	C
2	2					5		2			P
		SR	SL	R	L
3	3		1			6		3			P
		SBR	SBL							OUT 1	IN 3
4	4		2			7		4			Y
		FR	FL
5	5		3			8		5			P
		SUB	C
6	6		1			9		6			P
		SR	SL
1	1		2			4		1		3
		SBR	SBL
2	2		3			5		2		4
	OUT			R	L	OUT R	L		OUT		OUT
								S VIDEO	VIDEO	VIDEO	S VIDEO
URR R	SURR BACK R (ASSIGNABLE)		FRONT R			CENTER		FRONT L	SURR BACK L (ASSIGNABLE)
										SINGLE
	FRONT R (BTL)							FRONT L (BTL)

COMPONENT VIDEO	ANTENNA		12 V	RS232
		HDMI	TRIGGER
IN			OUT
Y			E
			IN 1
P
	FM			IR IN
	75			+12V DC PWR SUPPLY

PGND

IN 2

		MAIN
OUT		ZONE 2
		ZONE 3
Y	AM
		A
P		B
		C
		GND
		D
P		E
		OUT
		12V
SURR L		TRIGGER OUT
		AC INLET
	SPEAKERS A
	AC OUTLET
	AC 120V	60Hz
	SWITCHED
	120W 1A MAX.
	SPEAKERS B

UDD MODEL NO. DTR-10.5

47