Repeat Playback
(VHS deck only)
START REPEAT
1 Press and hold PLAY (until "
" blinks on the front display panel) during playback, then release.
SP
VCR
| ● The entire tape is played back 50 times. |
2 | STOP REPEAT |
To stop, press STOP at any time. | |
NOTE: | |
| Pressing PLAY, REW, FF, PAUSE or ª£also stops |
| Repeat Playback. |
Counter Reset (VHS deck only)
1 | RESET COUNTER TO ZERO |
Press C.RESET. | |
NOTE: | |
| By pressing the DISPLAY button, you can change the |
| display to show the counter reading, channel number, |
| clock time or tape remaining time. (Channel number is |
| not displayed during playback.) |
|
|
Next-Function Memory
The Next Function Memory “tells” the VCR what to do after rewinding. Before continuing, ensure that the VCR is in stop mode.
a– For Automatic Start Of Playback After Tape Rewind . . .
. . . press REW, then press PLAY within 2 seconds. b– For Automatic Power Off After Tape Rewind . . .
. . . press REW, then press POWER within 2 seconds.
Display Mode Setting
(DV Deck)
Set "DISPLAY" to "ON" to display the date and time at the original recording.
1 Press MENU to access the | DV MODE SET | |
Main Menu screen. | SOUND MODE | 32kHz |
2 Move the highlight bar | ||
(arrow) to "DV MODE SET" | 32kHz MODE | SOUND1 |
=DISPLAY | ON | |
by pressing CH5° or %Þ, |
|
|
then press OK or #. | = |
|
3 Move the highlight bar | SELECT WITH (5,°) AND (OK) | |
(arrow) to "DISPLAY" by | PRESS (MENU) TO END |
|
pressing CH5° or %Þ, |
|
|
then press OK or # to select "ON" or "OFF".
4Press MENU to return to the normal screen.
EN
27
Tape Position Indicator
(VHS deck only)
The Tape position indicator |
|
|
|
|
| |
appears on screen when, from the |
|
|
|
|
| |
stop mode, you press FF, REW, or |
|
|
|
|
| |
use the SHUTTLE ring, or perform |
|
|
|
|
| |
an Index Search. The position of |
|
|
|
|
| |
" " in relation to "B" (Beginning) | B | + | + | + | E | |
or "E" (End) shows you where you | ||||||
|
|
|
|
| ||
are on the tape. |
|
| COUNT |
| 0:33:27 |
NOTES:
●"SUPERIMPOSE" must be set to "ON", or the indicator will not appear (☞ pg. 25).
●It may take a few seconds for the Tape Position Indicator to be displayed.
Time Code (DV Deck)
During recording, a time code is recorded on the tape. This time code is used to confirm the position on the tape when playing or editing a tape. To perform Random Assemble Editing (☞ pg. 52), time code is necessary.
Seconds |
|
Minutes |
|
Hours | 0 : 00 : 00 |
NOTES:
The presence of a blank (unrecorded) portion in the middle of a tape can result in misoperation.
A "blank portion" of a tape is a section where nothing is recorded on the tape. If you start making a recording in a blank portion of a tape, the time codes will start from "0:00:00" again. If identical time codes are recorded in two different places on a tape, Random Assemble Editing and other similar functions might not operate properly.
In the following circumstances, you should play the tape and confirm where a scene ends, and then begin recording from there:
●When starting to record in the middle of a tape on which a recording has already been made.
●When you have made a recording on a tape, then played that recording back in order to check it, and now wish to continue recording.
●When you lost power or the batteries died while you were recording with a camcorder.
